Page 1
® PC4020 v3.3 • Instruction Manual WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read.
Page 2
FCC COMPLIANCE STATEMENT CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Table of Contents Introduction Section 1: General System Operation Getting to Know Your System ........... 4 Arming Your System ............5 Alternate Arming Methods ..........6 Disarming Your System ............7 Alarm Memory ..............8 What to Do If An Alarm Sounds ........8 Bypassing Zones ..............
Page 4
Table of Contents Section 5: Testing and Maintenance Performing a Walk Test ............. 28 Performing a System Test ..........29 Performing a Lamp Test (PC4216) ........29 System Maintenance ............29 Section 6: Fire Safety Fire Alarm Operation ............30 Guidelines for Locating Smoke Detectors ......
Introduction About Your Security System Your DSC security equipment has been designed to give you the greatest possible flexibility and convenience. The LCD keypad will guide you through each operation with English language prompts. The keypad provides audible feedback each time a key is pressed; with unique audible sequences, it will also signal system troubles and other indications of system status.
Section 1: General System Operation 1.1 Getting to Know Your System Your security system is made up of a control panel, one or more keypads and various detectors and sensors. The control panel will be mounted out of the way in a utility room or basement. The metal control cabinet contains the system’s electronics and stand-by battery.
S e c t i o n G e n e r a l S y s t e m O p e r a t i o n Keypads Several LCD keypads will be installed throughout the protected premises, usually one at each entry/exit door.
For Multi-Partition Access Codes When a multi-partition access code is entered, you must tell the system which partition(s) you wish to arm. The system will only offer to arm the partitions for which your code is programmed. Once you have entered your code, the display will read: (0) TO ARM <...
S e c t i o n G e n e r a l S y s t e m O p e r a t i o n Stay Arming This feature, if enabled, will allow you to arm the perimeter zones while leaving some interior zones inactive so that you can remain on the premises while the system is armed.
Disarming Another Partition If you have a multi-partition access code, you can disarm other partitions before entering them. To disarm another partition, enter your access code. The keypad display will read: (0) TO ARM < > (Partition Label) R Use the arrow (< >) keys to scroll to the partition you wish to disarm. Remember that only partitions to which your access code is assigned will be displayed.
S e c t i o n G e n e r a l S y s t e m O p e r a t i o n 1.7 Bypassing Zones You can use zone bypassing when access is needed to part of the protected area while the system is armed.
1.8 Viewing Trouble Conditions The alarm control panel continuously monitors a number of possible trouble conditions. If one of these conditions occurs, the keypad Trouble light will turn on and a beeping sound will be heard every 10 seconds. Press the [#] key to silence the keypad. The Trouble light will stay on until the trouble is cleared.
Section 2: Access Codes Access codes are used to arm and disarm the system as well as to access system functions. There are many different codes available on the system. The Grand System Master Code Grand System Master Code Grand System Master Code Grand System Master Code will be able to perform all system Grand System Master Code functions.
Page 14
Program Code You will need to program a four-digit code for each user. Six-digit access codes are also available. Talk to your installer if you require six- digit access codes on your system. To program the code for the new access code, perform the following: 1.
S e c t i o n A c c e s s C o d e s NOTE: If a user does not want their name listed on the PC4850 display, but does want to have an access code, you can put a “!” at the beginning of the user name.
Select (1) for User Name Search Press [1] or [ 3. The first letter of the access code name using the corresponding number key. For example, for John, enter the letter “J” by pressing the [4] key once. 4. The keypad will display the first available name starting with the selected letter.
Page 17
S e c t i o n A c c e s s C o d e s Table 2-1: Access Code User Options Default Settings* GM 2M SM System Master Select this option to program a System Master Code Supervisor Select this option to program a Supervisor code.
• • • • • ASCII Entry: ASCII Entry: ASCII Entry: ASCII Entry: ASCII Entry: This is for entering uncommon characters. Use the arrow (< >) keys to scroll through the available characters. Each character will be displayed along with the corresponding 3-digit ASCII number.
S e c t i o n A c c e s s C o d e s Duress Codes If the “Duress” user option is enabled, the code will become a Duress code. When this code is entered, the system will send a duress signal to the monitoring station.
Section 3: System Administration NOTE: To enter the [ ][6] menu, you may need to enter an access code that has the “System Master” or “Supervisor” option enabled. 3.1 Turning on Quick Arm Keypad Command: [ ][6][Access or Master Code][0][0] This option will allow users to arm the system by entering [*] [0] at any keypad, instead of entering an access code.
S e c t i o n S y s t e m A d m i n i s t r a t i o n 4. To exit the menu, press [#]. 5. Use the arrow keys (<>) to scroll to the “Auto Arm Time” display. Press [2] or [ ].
4. Next, use the keypad arrow keys to scroll to the display “Set System Date.” Press [ 5. Enter the current date (MMDDYY). For example, to program May 31, 2000 type “053100.” 6. Once the date and time have been programmed, press [#] twice to return the partition to its normal disarmed state.
S e c t i o n S y s t e m A d m i n i s t r a t i o n 3.8 Changing Keypad Settings Keypad Command: [ ][6][Master Code][3] The brightness of the keypad backlighting and the contrast of the keypad display can be adjusted.
3.10 PC-LINK Enable Option Keypad Command: [Master Code][9] If you are using the DLS-3 software with your system, your computer will be connected to the system with a PC-LINK module. If the module is disconnected from your system for any reason, after it is reconnected, you must select the PC-LINK enable option.
Section 4: Access Control NOTE: This section only applies to systems that have PC4820 Access Control modules, or PC4850 Telephone Entry modules installed. Talk to your installer for information regarding the access control capabilities of your system. 4.1 About Access Card Readers (PC4820 Modules) To gain access to an area via a door with an access card reader, present your access card through the reader.
4.2 Programming Access Cards (PC4820 Modules) Access card programming is a part of access code programming. An access card is assigned to a single user of the system. A user can have both an access code and an access card to provide two different means of accessing the system.
Page 27
S e c t i o n A c c e s s C o n t r o l Your installer will customize access levels 02-63 to suit your purposes. Assigning access level 00 means that the user will never have access to a given area.
4.3 Searching Using Access Card Numbers (PC4820 Modules) In Section 2.2 “Modify an Existing Code,” two methods were outlined for searching for existing users: by access code number and by user name. You may also search by access card number. To do so, perform the following: 1.
S e c t i o n A c c e s s C o n t r o l 4.5 Adding Tenant Codes for Users (PC4850 Modules) You can give visitors the option of entering a 1-4 digit code on the keypad to call a user.
Section 5: Testing and Maintenance IMPORTANT NOTE: Test your system on a weekly basis and have any system trouble conditions corrected by your installer or service technician. 5.1 Performing a Walk Test Keypad Command: [ ][6][Walk Test Code] The Walk Test feature allows you to test if the detectors on a partition are in proper working order.
S e c t i o n T e s t i n g a n d M a i n t e n a n c e Disable Walk Test To end every walk tests—except the “AML Smoke Test”—this option must be selected.
Section 6: Fire Safety 6.1 Fire Alarm Operation The following explains the fire alarm function of this system. 1. Fire Bells Sound Upon a fire alarm, the bells or sirens will sound. They will pulse on and off in a programmed pattern. The keypad will display the following: First Fire Alarm [Zone Label] The display will indicate the first fire zone in alarm, followed by any...
Page 33
S e c t i o n F i r e S a f e t y Do not locate smoke detectors at the top of peaked or gabled ceilings; the dead air space in these locations may prevent the unit from detecting smoke. Avoid areas with turbulent air flow, such as near doors, fans or windows.
6.3 Household Fire Safety Audit Most fires occur in the home. To minimize this danger, a household fire safety audit should be conducted and a fire escape plan should be developed and practised. 1. Are all electrical appliances and outlets in a safe condition? Check for frayed cords, overloaded lighting circuits, etc.
Page 35
S e c t i o n F i r e S a f e t y • A good plan emphasizes quick escape. Do not investigate or attempt to fight the fire, and do not gather belongings or pets as this wastes valuable time.
Appendix A – Special Characters Below is a chart indicating the available ASCII characters and the 3-digit number required for each character. Instructions on programming ASCII characters is outlined in Section 2 “Access Codes.”...
Page 37
LIMITED WARRANTY able number of attempts will be limited to a replace- Digital Security Controls Ltd. warrants the original ment of the product, as the exclusive remedy for breach purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials of warranty.
Page 38
alert occupants of a fire for a number of reasons, some of which WARNING Please Read Carefully follow. The smoke detectors may have been improperly installed or positioned. Smoke may not be able to reach the smoke de- Note to Installers tectors, such as when the fire is in a chimney, walls or roofs, or This warning contains vital information.
Page 39
A A A A A VIS: VIS: VIS: VIS: L’étiquette de l’Industrie Canada identifie VIS: ne dépasse pas 100. le matériel homologué. Cette étiquette certifie que L’Indice de charge de ce produit est 0.1B. le matériel est conforme à certaines normes de NOTICE: NOTICE: NOTICE:...