Modify An Existing Code; Change User Code Options; Delete An Existing Code - DSC PC4020 Installation Manual

code for the apartment. If a user knows a visitor is coming,
they can give them the tenant code as a faster way to call
them. For this to work, the user's telephone number must
also be programmed (see section 4.4).
Tenant codes cannot begin with '0'.
1. Enter [*][5] followed by a Master code.
2. Locate the access code for the user with one of the code-
searching methods (see Section 2.2 'Modifying an Exist-
ing Code'). Press [*] to select.
3. Use the right arrow (>) key to scroll to the following dis-
play:
Select (8) < >
Tenant Code
4. Press [8] or [*].
5. Enter up to 4 digits for the tenant code.
6. When you are finished, press [#].

7.4 Modify An Existing Code

To modify an existing code, you must first search for it
using one of two methods: search by user number or by
user name.
To search for the code by user number
ing:
1. Enter [*][5] followed by a Master code.
2. The display will read:
Select (0) for
User Number Search
Press [0] or [*].
3. Enter the access code number and press [*] to continue
programming. You can also use the arrow (< >) keys to
scroll to the desired number.
To search for the code by user name
1. Enter [*][5] followed by a Master code.
2. The display will read 'Select (0) for User Number
Search'. Use the right arrow (>) key to scroll to the fol-
lowing display:
Select (1) for
User Name Search
Press [1] or [*].
3. The first letter of the access code name using the corre-
sponding number key. For example, for John, enter the
letter 'J' by pressing the [4] key once.
4. The keypad will display the first available name start-
ing with the selected letter. Use the right arrow (>) key
to scroll through subsequent names.
5. Once the appropriate user name is displayed, press [*]
to continue programming.
Once the code has been selected, the Program Code menu
will be shown. Reprogram the access code, code label or
partition access using the steps outlined in "Program A
New Code".

7.5 Change User Code Options

User code options determine which system features the
code will be able to access. The Access User Code Options
Table shows all of the available access code options. The
table also indicates which options are enabled by default for
each type of code.
To change the user options for a code from its default set-
tings, perform the following:
1. Enter [*][5][master code].
2. Locate the code using one of the code searching meth-
ods (see section 7.3 "Programming Access Codes").
Press [*] to select.
3. Use the right arrow (>) key to scroll to the following dis-
play:
Select (5) < >
Edit User Opt's
Press [5] or [*].
4. Use the arrow (< >) keys to scroll through each option.
Press [*] to turn each option on (Y) or off (N).
user number, perform the follow-
user number user number
user name, perform the following: user name user name
I n s t a l l e r
5. When the desired options have been programmed,
press [#].
Access Code User Options
System Master System Master
System Master System Master
Select this option to program a Grand System Master
Code
Supervisor Supervisor
Supervisor Supervisor
Select this option to program a Supervisor code. You
must also program the partition mask for this code.
Arm Arm
Arm Arm
Allows arming of the assigned partition(s).
Disarm Disarm
Disarm Disarm
Allows disarming of the assigned partition(s).
Bypass Bypass
Bypass Bypass
Allows bypassing of zones on the assigned
Command Output Command Output
Command Output Command Output
Allows activation of a [*][7][X] command output when an
access code is required. For more information, ask your
installer.
Duress Pulse Duress Pulse Duress Pulse Duress Pulse
Select option for Duress codes only.
One-Time Use One-Time Use One-Time Use One-Time Use
Select option for One-Time Use codes only (see
"Special Codes")
Escort4580 Access Escort4580 Access Escort4580 Access Escort4580 Access
Allows access to the Escort4580 audio assistant, if
installed.
Global Access Global Access Global Access Global Access
Allows use of a Global keypad.
Partition Select Menu Partition Select Menu Partition Select Menu Partition Select Menu
Allows all accessible partitions to be viewed when the
code is entered.
Card Valid For Access Control Systems only. Card Valid
Card Valid Card Valid
Privilege Card (same as previous) Privilege Card Privilege Card Privilege Card
Wait for Prvl (same as previous) Wait for Prvl
Wait for Prvl Wait for Prvl
Silence Fire Silence Fire
Silence Fire Silence Fire
Allows the user to silence and reset any Fire Alarms on
the selected partitions by entering their access code on
the partition keypad.
T-Code T-Code T-Code T-Code
T-codes can be turned on or off by partition using
the "Special - T-code" function key.
Telephone Number Telephone Number Telephone Number Telephone Number
If a PC4850 Telephone Entry module is connected,
enter a 12-digit telephone number for each user.
Tenant Code Tenant Code Tenant Code Tenant Code
If a PC4850 Telephone Entry module is connected,
enter a 4-digit tenant code (tenant codes cannot
start with 0).
Change Code Change Code Change Code Change Code
When this option is enabled, the user will only be
allowed to change their access code.
Disarm Delay Disarm Delay Disarm Delay Disarm Delay
When this option is enabled, the user will not be able to
disarm the partition immediately. A delay will occur before
disarming (see Section 8.4).
Group Bypass Group Bypass Group Bypass Group Bypass
When this option is enabled, the user will be able to bypass
a group of zones that are set up for Group Bypassing (see
Section 5.5).
* Code abbreviations: GM = Grand System Master; 2M = Second Master;
SM = System Master; S = Supervisor; AC = Access Code (default).
The options for the Grand System Master and Second Master codes cannot be
changed from their default settings.
**For the System Master code, the supervisor option changes to Yes after you exit
access code programming.

7.6 Delete An Existing Code

An access code may be erased in two parts. First, all data
pertaining to the code may be deleted (access code, user
options, partition access, etc.). The access code label is
erased separately.
To delete all access code data from an existing code, per-
form the following:
1. Enter [*][5][master code].
a n d A c c e s s C o d e s
Default Settings*
GM 2M SM S AC
Yes
**
Y es Yes
Yes Yes Yes Yes Yes
Yes Yes Yes Yes Yes
Yes Yes Yes Yes Yes
partition(s).
Yes Yes Yes Yes Yes
Yes Yes Yes Yes Yes
Yes Yes Yes Yes Yes
Yes Yes Yes Yes Yes
Yes Yes Yes Yes Yes
Yes Yes
Yes Yes Yes Yes Yes
No No No No No
No No No No No
Yes Yes Yes No No
25