Dish Network 112182 User Manual page 112

Chapter 5
Reference
C C
HANNEL HANGES
What's
Happening
You enter • Maybe you made a mistake when you
a channel number entered the channel number, or maybe
you want. the channel number you entered
The channel doesn't work. If so, the receiver tunes
changes, to the channel closest to the channel
but the new you entered.
channel isn't If you entered the number for a
exactly the channel you haven't bought, the
channel you receiver tunes to the channel and gives
entered. you the choice to buy it.
You're scanning • If you apply a Favorites List that's not
All Chan, the receiver skips channels
up or down
through the that aren't on the applied list.
channels, and the
• If you hide adult channels and lock
receiver skips
the receiver, the receiver skips adult
channels you
channels.
know you bought.
The receiver • Stray UHF signals from a nearby
changes channels neighbor are interfering with your
by itself. receiver.
D DVR F
ISH EATURES
What's
Happening
You find you can't • If the receiver runs out of room to auto
watch part of a record a program, it starts to erase the
program you're auto oldest part of the program to make room
recording. for new audio and video.
• When you change the channel, you
erase what's stored in auto recording.
• You can't watch part of a "live"
program that hasn't been broadcast yet,
because the receiver hasn't recorded it
yet.
You find the • Maybe you didn't press the remote
control RECORD button while you
receiver didn't
on-demand record watched the program or set an Event
a program. Timer to record it.
• Maybe the receiver ran out of room
to on-demand record the program.
• You may have had a signal outage
caused by bad weather during the
recording.
You find the If you don't "protect" a recorded program,
receiver is missing and the receiver needs room to record a new
programs you program, it may record over that recorded
recorded. program to have room.
When you open a You see menu options only when they
work. For example, the Start option
recorded program's
info menu, some of doesn't show up unless you select a
the options seem to recorded program.
be missing.
On-demand On-demand recording works by program
recording stores unless you set a manual event timer to start
only one program, and stop the recording at the times you set
or only part of one yourself.
program.
Page 106
What's Wrong
What's Wrong
What You Can Do
• Carefully enter the channel number you want again.
• Press the remote control RECALL button to go back to the previous
channel number.
• To buy a channel, call the Customer Service Center
at 1-800-333-DISH (3474).
• Press GUIDE until All Chan is the active Favorites List.
• Unlock the receiver so it doesn't skip adult channels.
• Install a 10 dB attenuator as described in Attach an Attenuator.
What You Can Do
• To make sure you can watch all of a program, on-demand record it instead
of auto recording it.
• If you want to be able to watch all of a program you're auto recording,
don't change the channel. You can only auto record for about one hour.
• To on-demand record a program, you must either press the remote control
RECORD button or set an Event Timer. If you set an Event Timer to
record the program, maybe the Event Timer was not set up right. See the
Event Timers table for help.
• Check the "time Left" on the DishDVR Recorded Events menu.
If you "protect" many recorded programs, the receiver may not have
enough room to record any new programs.
Use the DishDVR Recorded Events menu to "protect" an on-demand
recorded program. This means the receiver will ask you before it records over
that recorded program. But note, if you "protect" many recorded programs,
the receiver may not have enough room to record any new programs.
You can use only the options you see on the menu. You won't see all the
options at once. You'll never see a "Record" option; to record a program you
must either press the remote control RECORD button or set an Event Timer.
To record more than one program, or to record parts of one or more programs,
set a manual event timer.