Alarm - CARLO GAVAZZI WM5-96 - PROGRAMMING Instruction Manual

Programming WM5 96
24

Alarm

* * * * * * * * * * M M A A I I N N M M E E N N U U * * * * * * * * * *
DISPLAY PAGE
DIGITAL INPUTS
DIGITAL OUTPUTS
ALARMS
R R E E V V . . 1 1 . . 4 4 . . 2 2 . . 6 6
1
* * * * * * * * * * A A L L A A R R M M S S M M E E N N U U * * * * * * * * * *
ALARM 01 (OFF)
ALARM 02 (ON)
ALARM 03 (ON)
ALARM 04 (ON)
ALARM 05 (ON)
2
* * * * * * * * * * A A L L A A R R M M S S M M E E N N U U * * * * * * * * * *
ENABLE
VARIABLE
TYPE
A A L L A A R R M M : : 0 0 1 1
E E N N A A B B L L E E : : O O F F F F
3
OFF UP
3b
3a
ON DO
IN
OUT
* * * * * * * * * * A A L L A A R R M M S S M M E E N N U U * * * * * * * * * *
LATCH
DISABLE
SET 1
A A L L A A R R M M : : 0 0 1 1
L L A A T T C C H H : : O O F F F F
4
OFF
SET 1 ?
4a 4c
min
ON
max
* * * * * * * * * * A A L L A A R R M M S S M M E E N N U U * * * * * * * * * *
SET 2
OUT
DELAY ON
A A L L A A R R M M : : 0 0 1 1
D D E E L L A A Y Y O O N N 2 2 : : 0 0 . . 0 0 0 0 0 0
5
0.0000.
SET 2 ?
-9999G
min
9999G
max
5a
DELAY ON ?
min
max
This function allows you to set the alarm parameters. The instrument is
able to manage up to 16 alarms (real or virtual). Select the ALARMS func-
Measure
tion
the alarm to be programmed
> 2s
firm with the "S" key, then set the following parameters:
( ( A A V V 5 5 ) )
ENABLE (3): enable (ON) or disable (OFF) the alarm; the instrument dis-
play the existing programming (a). Select the ENABLE function
means of the "
(3a)
Go back
keys, then confirm with the "S" key.
VARIABLE (3): set the variable to be coupled to the alarm. Select the VARI-
> 2s
ABLE submenu
key. Then select the variable to be coupled to an alarm (the list of variables
depends on the selected system)
select with the "S" key.
TYPE (3): set the operating mode of the alarm. UP: up alarm, the alarm
will be enabled if the measured value exceeds the set-point. DO: down
alarm, the alarm will be enabled if the measured value goes below the set
point. IN: internal window alarm, the alarm will be activated if the value is
brtween the two set points. OUT: the alarm will be activated if the value
is outside the two set points. See details on next page "Logic and alarm
a
parameters". Choose the TYPE
confirm with "S". Then, select by means of the "
alarm mode
V1
LATCH (4): set the latch function. The alarm will remain ON even if the
3c
A1
cause that has generated it is not present any more. The alarm can be
W1
reset only manually after the user has noticed it. Choose the LATCH func-
var1
tion by means of the "
(4a)
able it, then confirm with "S".
DISABLE: set the DISABLE function. When the instrument is switched
on, the first alarm condition will be ignored (useful also in case of DOWN
alarm). Choose the DISABLE function by means of the "
confirm with "S". Then select ON
it by means of the "
SET 1 (Set point 1) (4): set the first alarm set point of the variable. Choose
SET 1
9.0000.
OFF
4b
-9999G
the value by means of the "
ON
9999G
SET 2 (5): set the second alarm set point of the variable. Choose SET 2
(5a)
value by means of the "
OUT (5): select the output to be enabled in case of alarm. The list will dis-
play all the outputs that in the menu "Digital outputs" have been set as
"alarm". Choose the OUT function by means of the "
confirm with "S". NONE-FFT, virtual alarm with trigger function for sig-
nal FFT analysis. The analysis relevant to the 10s that precede the
alarm event will be stored (FIFO) and available for the remote down-
loading by means of a specific software PowerSoft.Then select by
means of the "
OUT D0
5b
DELAY ON (5): set a delay on activation of the alarm. Choose the func-
OUT D3
tion DELAY ON by means of the "
NONE-FFT
00000s Then set the value in seconds
5c
00000s
confermare con "S".
25500s
DELAY OFF (6): set a delay on deactivation of the alarm. Choose the
DELAY OFF function by means of the "
Afterwards set its value in seconds
then confirm it with "S".
(1) by means of the "
" keys and confirm with the "S" key. Then select ON
to enable or OFF (3a) to disable the alarm by means of the "
(3) by means of the "
(3b) and confirm with "S".
" keys and confirm with "S". Then select ON
by means of the " " keys to enable the latch or OFF
" keys and confirm with "S".
(4c) by means of the "
by means of the "
" keys the desired output
WM5-96 Instruction Manual
" keys and confirm with "S". Then select
(2) by means of the "
" keys and confirm with the "S"
(3c) by means of the "
(3) function by means of the "
(4b) to enable it or OFF
" keys and confirm with "S". Then set
" keys and confirm with "S".
" keys and confirm with "S". Then set the
" keys, then confirm with "S".
(5b) then confirm with "S".
" keys and confirm with "S".
(5c) by means of the "
" keys and confirm with "S".
(6a) by means of the "
" keys and con-
(3) by
"
" keys, then
" and
" keys the desired
(4a) to dis-
" keys and
(4b) to disable
" keys and
" keys quindi
" keys