Altronix NetWay Spectrum NetWay4EBT3 Series Installation Manual page 5

Configuring Units for Network Connection
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Please be sure to visit altronix.com for latest firmware and installation instructions
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Factory Default Settings
• IP Address:
• User Name:
• Password:
1. Set the static IP address for the laptop to be used for programming to the same network IP address as the
Netway4EBTB. The default address of the Netway4EBTB is 192.168.168.168, I.E. 192.168.168.200.
2. Connect one end of the network cable to the network jack on the Netway4EBTB and the other to the network
connection of the laptop.
3. Open a browser on the computer and enter "192.168.168.168" into the address bar.
A dialog box Authentication Required will appear requesting both user name and password.
Enter the default values here. Click on the button labeled Log In.
4. The status page of the Netway4EBTB will appear. Click on the tab labeled Network Settings.
This will open the Network Setting screen. In this screen the MAC Address of the Netway4EBTB module
will be found along with the Network Settings and Email Settings.
Network Settings:
In the IP Address Method field select [STATIC] or [DHCP], then follow the appropriate steps.
Static:
A. IP Address: Enter the IP address assigned to the Netway4EBTB by the network administrator.
B. Subnet Mask: Enter the Subnet of the network.
C. Gateway: Enter the TCP/IP gateway of the network access point (router) being used.
Gateway configuration is required to properly receive emails from the device.
D. HTTP Port: Enter the HTTP port number assigned to the Netway4EBTB module by the network administrator
to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not encrypted and
unsecure. Even though HTTP can be used for remote access, it is recommended primarily for use with
LAN connections.
E. HTTPS Port: Enter the HTTPS port number assigned to the Netway4EBTB module by the network
administrator to allow remote access and monitoring. The default inbound port setting is 443.
Being encrypted and more secure, HTTPS is highly recommended for remote access.
F. Click the button labeled Submit Network Settings.
A dialog box will display "New network settings will take effect after the server is rebooted". Click OK.
DHCP:
A. After selecting DHCP in the IP Address Method field click the button labeled Submit Network Settings.
A dialog box will display "New network settings will take effect after the server is rebooted". Click OK.
Next, click on the button labeled Reboot Server. After rebooting the Netway4EBTB will be set in the DHCP
mode. The IP address will be assigned by the router when the Netway4EBTB is connected to the network.
It is recommended to have the assigned IP Address reserved to ensure continued access
(see the network administrator).
B. Subnet Mask: When operating in DHCP, the router will assign the subnet mask values.
C. Gateway: Enter the TCP/IP gateway of the network access point (router) being used.
D. HTTP Port: Enter the HTTP port number assigned to the Netway4EBTB module by the network administrator
to allow remote access and monitoring. The default inbound port setting is 80. HTTP is not encrypted and
unsecure. Even though HTTP can be used for remote access, it is recommended primarily for use with
LAN connections.
Secure Network Setup (HTTPS):
In order to setup HTTPS for a Secure Network Connection, a Valid Certificate and Key must be used. Certificates
and Key should be in a ".PEM" format. Self Certifications should only be used for testing
purposes as no actual authentication is being performed. In a Self-Certified mode, the connection will still state
that it is unsecure. How to upload Certificate and Key to setup HTTPS:
Netway4EBT3 Series Installation Guide
192.168.168.168
admin
admin
- 5 -