Download Print this page
Altronix NetWaySP4TCW53 Installation Manual
Altronix NetWaySP4TCW53 Installation Manual

Altronix NetWaySP4TCW53 Installation Manual

4-port hardened 360w 802.3bt 4ppoe switch (layer 2) with rapid battery charger
Hide thumbs Also See for NetWaySP4TCW53:

Advertisement

Quick Links

Embedded
Fiber Solution
NetWaySP4TCW53
4-port Hardened 360W 802.3bt
4PPoE Switch (Layer 2)
with Rapid Battery Charger
- Includes Vent2
Installation Guide
DOC#: NetWaySP4TCW53 Rev. 081924
More than just power.
TM
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________

Advertisement

loading
Need help?

Need help?

Do you have a question about the NetWaySP4TCW53 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Altronix NetWaySP4TCW53

  • Page 1 Fiber Solution NetWaySP4TCW53 4-port Hardened 360W 802.3bt 4PPoE Switch (Layer 2) with Rapid Battery Charger - Includes Vent2 Installation Guide DOC#: NetWaySP4TCW53 Rev. 081924 More than just power. Installing Company: _______________ Service Rep. Name: __________________________________ Address: _____________________________________________ Phone #: __________________...
  • Page 2 Overview: Altronix NetWaySP4TCW53 Hardened 802.3bt 4PPoE Layer 2 Switch is equipped with two (2) 1Gb SFP ports and four (4) 802.3bt compliant Ethernet ports rated at 90W each, with 360W total power for deploying the latest high- powered IP devices in remote locations.NetWaySP4TCW53 accommodates single/multi-mode fiber or composite cable (fiber+copper) to simultaneously deliver power and data from NetWay Spectrum head-end media converters/ injectors.
  • Page 3 [– BAT +] (Fig. 1, pg. 4). When use of stand-by batteries is desired, they can be lead acid or gel type. If batteries are housed inside the enclosure, it must be properly ventilated. Use included Altronix Vent2 kit.
  • Page 4 IEEE 802.3bt Batteries PoE/PoE+/Hi-PoE PoE/PoE+/Hi-PoE Device Device PoE/PoE+, Hi-PoE or EBC48 BT Device mounted below NetWaySP4BTB Fig. 1a Fiber to the Factory next Netway Spectrum Fiber to Reset 115/230VAC Switch Hardened PoE Switch* Input - 4 - NetWaySP4TCW53 Installation Guide...
  • Page 5 Configuring Unit for Network Connection: –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Please be sure to visit altronix.com for latest firmware and installation instructions –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Factory Default Settings: • IP Address: 192.168.168.168 • User Name: admin • Password: admin 1. Set the static IP address for the laptop to be used for programming to the same network IP address as the NetwaySP4BT.
  • Page 6 It is important to plan how you will setup your devices for each vLan. Configuring vLan on the Altronix NetwaySP4BT3 Series Layer 2 Switch: 1. Ensure Laptop or PC being used to program the vLan settings is on a port that will be assigned to your first vLan configuration.
  • Page 7 (Fig. 1a, pg. 4; Fig. 3, pg. 7). Continue holding the button until the LEDs on board go through the start up cycle, then release the button. 3. The unit returns to the original factory settings. Fig. 3 Factory Reset NetWaySP4TCW53 Installation Guide - 7 -...
  • Page 8 Installing Vent2 on NetWaySP4TCW53: Fig. 4 Left Side of Enclosure Bottom of Enclosure 7” 1.75” 1. Using the template from the Vent2 bag, install the vents in the positions shown above. - 8 - NetWaySP4TCW53 Installation Guide...
  • Page 9 This installation should be made by qualified service personnel. This product contains no serviceable parts. PMK2 outdoor pole mount kit is designed to simplify the installation of Altronix outdoor rated power supplies and accessories housed in WP5 NEMA rated enclosures. PMK2 can be mounted on 2” to 8” (50.8mm to 203.2mm) diameter round or 5”...
  • Page 10 Notes: - 10 - NetWaySP4TCW53 Installation Guide...
  • Page 11 Notes: NetWaySP4TCW53 Installation Guide - 11 -...
  • Page 12 BRASS INSERT (X4) 10-32 X 0.25” (6.4mm) BRASS INSERT (X2) Altronix is not responsible for any typographical errors. –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty...