Advertisement
Quick Links
Fiber Solution
NetWaySP8C Series
8-port Hardened 360W Ethernet over Fiber
Hardened Switches with Rapid Battery Charger
Models Include:
NetWaySP8C3W2
- Enclosure accommodates two (2) 12VDC/7AH or
up to four (4) 12VDC/4AH batteries
- 115/230VAC Input
- Includes Vent2
NetWaySP8C3W5
- Enclosure accommodates
four (4) 12VDC/12AH batteries
- 115/230VAC Input
- Includes Vent2
Installation Guide
DOC#: NetWaySP8C Rev. 120424
Installing Company: _______________ Service Rep. Name: __________________________________
Address: _____________________________________________ Phone #: __________________
NetWaySP8C7W2
- Enclosure accommodates two (2) 12VDC/7AH or
up to four (4) 12VDC/4AH batteries
- 277VAC Input
- Includes Vent2
NetWaySP8C7W5
- Enclosure accommodates
four (4) 12VDC/12AH batteries
- 277VAC Input
- Includes Vent2
More than just power.
Embedded
™
TM
Advertisement
Related Manuals for Altronix NetWaySP8C Series
Summary of Contents for Altronix NetWaySP8C Series
- Page 1 Embedded ™ Fiber Solution NetWaySP8C Series 8-port Hardened 360W Ethernet over Fiber Hardened Switches with Rapid Battery Charger Models Include: NetWaySP8C3W2 NetWaySP8C7W2 - Enclosure accommodates two (2) 12VDC/7AH or - Enclosure accommodates two (2) 12VDC/7AH or up to four (4) 12VDC/4AH batteries...
- Page 2 Overview: Altronix NetWaySP8C3W Series Hardened Switches are each equipped with two (2) 1Gb SFP ports and eight (8) PoE+ (30W) ports or up to two (2) Hi-PoE (60W) ports, with 360W total power for deploying the latest high-powered IP devices in remote locations. NetWaySP8C3W Series accommodate single/multi-mode fiber or composite cable (fiber+copper) to simultaneously deliver power and data from NetWay Spectrum head-end media converters/injectors.
- Page 3 Using 4A charging current setting will allow to return ~28AH of charge into the appropriate size battery. Battery performance is dependent on battery specifications from the manufacturer. This includes tempera- ture ratings, charge capacity, charge/discharge cycles and depth of discharge. Altronix is not responsible for battery installation methods.
- Page 4 If batteries are housed inside the enclosure, it must be properly ventilated. Use included Altronix Vent2 kit and follow its installation instructions. Note: When batteries are not used, a loss of AC will result in the loss of output voltage.
- Page 5 Configuring Units for Network Connection –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Please be sure to visit altronix.com for latest firmware and installation instructions –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– Factory Default Settings • IP Address: 192.168.168.168 • User Name: admin • Password: admin 1. Set the static IP address for the laptop to be used for programming to the same network IP address as the NetwaySP8.
- Page 6 2. Depress Factory Reset button on NetWaySP8B while reapplying power to the unit (Fig. 2a, pg. 5; Fig. 3 pg. 7). Continue holding the button until the LEDs on board go through the start up cycle, then release the button. 3. The unit returns to the original factory settings. Fig. 3 Factory Reset - 6 - NetWaySP8C Series Installation Guide...
- Page 7 It is important to plan how you will setup your devices for each vLan. Configuring vLan on the Altronix NetwaySP8 Series Switch: 1. Ensure Laptop or PC being used to program the vLan settings is on a port that will be assigned to your first vLan configuration.
- Page 8 5-6 for ports 1-4 USB Port for Configuring Pass thru Trunk (i.e. VLan ID 10 and/or 20) (i.e. VLan ID 10 and 20) Fiber to Fiber from Next NetWaySP82 Host Switch - 8 - NetWaySP8C Series Installation Guide...
- Page 9 1. Using the template from the Vent2 bag, install the vents in the positions shown above. Installing Vent2 on NetWaySP8C3W5/NetWaySP8C7W5 Fig. 6 Left Side of Enclosure Bottom of Enclosure 7” 1.75” 1. Using the template from the Vent2 bag. Install the vents in the positions shown above. NetWaySP8C Series Installation Guide - 9 -...
- Page 10 This installation should be made by qualified service personnel. This product contains no serviceable parts. PMK2 outdoor pole mount kit is designed to simplify the installation of Altronix outdoor rated power supplies and accessories housed in WP5 NEMA rated enclosures. PMK2 can be mounted on 2” to 8” (50.8mm to 203.2mm) diameter round or 5”...
- Page 11 ATTACHED WITH RIVETS. Ø 0.375 PADLOCK EYE 14.54” (369.3mm) 14.00” (355.6mm) SECTION A-A 12.23” (310.6mm) 0.125” (3.2mm) MOUNTING PLATE END VIEW Ø 0.32” (8.1mm) WALL MOUNTING HOLE X 4 10-32 X 0.250 BRASS INSERT 4 PLCS. 12.00” (304.8mm) NetWaySP8C Series Installation Guide - 11 -...
- Page 12 BRASS INSERT (X4) 10-32 X 0.25” (6.4mm) BRASS INSERT (X2) Altronix is not responsible for any typographical errors. –––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––– 140 58th Street, Brooklyn, New York 11220 USA | phone: 718-567-8181 | fax: 718-567-9056 website: www.altronix.com | e-mail: info@altronix.com | Lifetime Warranty...
Need help?
Do you have a question about the NetWaySP8C Series and is the answer not in the manual?
Questions and answers