Gastroback DESIGN MULTI JUICER DIGITAL PRO Operating Instructions Manual page 60

Problem Reason The Solution
After some minutes Due to the power This is normal and inevitable.
of operation, the that is transmitted by
glass jug gets tan- the motor, your food
gibly warm. may heat up a little.
When crushing ice in You did not cool If the glass jug is still at room temperature, when filling in ice, the
the mixing system, down the mixing jug ice will melt during crushing. Place the mixing jug at least into the
the ice is melting before operation. refrigerator before filling. Alternatively, cool the mixing jug by filling
too fast. in some ice and leaving the mixing jug cool down for some minutes.
Then discard the ice and fill in a new portion for crushing.
You left the appli- Due to the power that is transmitted by the motor, the interior
ance operate for a of the mixing jug is warmed up, melting your ice. We recom-
too long time. mend to operate the appliance in short pulses.
Grinding System: The grinding results In most cases, you need to select another speed. Select a low-
When grinding, the depend on the type er speed for getting a coarser result (e.g. granulates), select a
results do not reach and freshness of high speed level for a finer grind size (powder).
the desired consi-
your food, the speed
stency. selection, and the
processing time.
Grinding System: The ingredients give Try to add some sugar or salt to absorb the oils/moisture.
The ingredients go off too much oil or
lumpy during grin- moisture.
ding.
The interior of the Always completely dry all parts of the grinding system, before
grinding system has filling in your food. Especially at the blade assembly, residues of
been moist. moisture could remain after cleaning.
It seems to be The blade assembly Get some help for unscrewing: one person holding the glass
impossible to has been screwed container, the second one clasping the collar of the blade
unscrew the blade on too tightly. assembly.
assembly from the
For locking an acces- DO NOT hold any of the accessories for mixing or grinding by
glass container.
sory for mixing or the glass container for locking onto the motor base. ALWAYS
grinding to the motor grasp the collar of the blade assembly to avoid over-tightening
base, you grasped the the junction to the glass container. Get some help for unscrew-
system by the glass ing.
container.
Sticky food (e.g. suga- Soak the glass container in warm dishwater for approx. 1 hour.
ry juice) adheres to Then try again. Get some help for unscrewing.
the sealing surfaces.
118
Problem Reason The Solution
The sealing surface Get some help for unscrewing. Do not use any chipped or cra-
of the glass container cked glass parts for preparing food any longer to avoid injuries
has been chipped due to splinters in your food! Replace the glass container.
when screwing on Check the sealing ring for damage, before using the sealing ring
the blade assembly. again.
CARE AND CLEANING
This appliance shall not be used by children. Keep the appli-
WARNING:
ance and its cord out of reach of children. Always switch OFF (turn the selection
dial to the "OFF" position, switch the power switch to "O") and unplug the appli-
ance, before cleaning the appliance. Do not spill or pour any liquids on or in the
motor base or power cord. Do not place or immerse the motor base or power cord
in any liquids to avoid damage, risk of fire, and electric shock. Keep the motor base
always completely dry and clean. Systems for mixing and grinding: Glass can easi-
ly break or crack. Always use special care while handling the glass containers
(mixing jug, grinding cup). Do not expose the glass containers to extreme tempera-
ture variations. Do not fill hot food or hot liquids into the glass containers or place
the glass containers into hot liquids or on hot surfaces. Do not use abrasive cleaning
agents or aggressive cleaners (e.g. bleach, solving agents) for cleaning the appli-
ance or any part of it, to avoid damage to the surfaces and sealing rings. Do not
use any hard or sharp-edged objects for cleaning (e.g. scoring pads, metal cooking
utensils). Do not use violence! DO NOT place the motor base or power cord in an
automatic dishwasher!
Clean the appliance and accessories always immediately after use, to avoid the
build-up of stubborn residues and discolouration. Do not store your food in the con-
tainers of the appliance.
DISASSEMBLING THE JUICING SYSTEM
After operation, you should always disassemble the juicing system, empty the pulp
container and juice jug, and rinse all parts at once to avoid discolouration of the
plastic parts and food drying on the surfaces. For this, proceed as follows.
WARNING: The blades in the base plate of the juicing sieve are very sharp.
Always handle the juicing sieve by the rim or the dark drive coupling.
Tip: It is good advice to hold a sufficiently large tray at hand for placing the parts
of the juicing system on it. This may keep your working space clean.
119