Gastroback DESIGN MULTI JUICER DIGITAL PRO Operating Instructions Manual page 58

Problem Reason The Solution
The pulp container is Immediately unplug the appliance. Clean and dry the appliance
overfilled. (see: 'Cleaning the Juicing System') and leave the motor base
dry naturally for 1 day. Do not overfill the pulp container or
juice jug during processing (see: 'Emptying the Containers and
Removing Obstacles').
The juicing sieve is Immediately unplug the appliance. Clean and dry the appliance
overfilled. (see: 'Cleaning the Juicing System') and leave the motor base
dry naturally for 1 day. Do not overfill the feed chute. Do not
apply too much pressure onto the food pusher during juicing
(see: 'Emptying the Containers and Removing Obstacles' and
'Method of Operation and Making Breaks').
Juice sprays out and Some juices are Do not apply too much pressure. If possible, process this type of
splashes at the juice very frothy, causing food in combination with other foodstuffs.
spout. splashing at the jui-
ce spout.
The drip-stop is not Ensure to open the drip-stop by turning the stainless steel sleeve
completely open. at the juice spout (see: 'Drip-Stop Feature').
The pulp is very You are pushing too Do not apply too much pressure when pushing down your food.
wet. You get an fast and with too Push your food slowly and evenly down the feed chute.
insufficient amount much pressure on
of juice. the food pusher.
The mesh in the Remove excess fibre building up in the mesh and blocking the
juicing sieve is fine pores. Rinse the juicing sieve (see: 'Emptying the Contai-
clogged. ners and Removing Obstacles'). Try to process fibrous foodstuffs
in turn with soft and juicy ingredients.
Only little amount of The amount of juices you can get from individual batches of
juices in your food. ingredients may vary to a high degree (see: 'Tips for Juicing').
You are processing Some types of fruit (e.g. mangoes, quinces) will only give off
a type of fruit that there juices when squeezed (see: 'Tips for Juicing').
is not suited for this
kind of juicer.
Excessive pulp is The pulp guttering is Switch "OFF" the Juicer and unplug from the power supply.
building up in the clogged. Remove the obstacle according to the instructions in section
juicing sieve. 'Emptying the Containers and Removing Obstacles'.
The selected speed Select a higher speed level.
is too low.
114
Problem Reason The Solution
Too much pressure Press evenly and slowly onto the food pusher.
on the food pusher.
You are processing Switch "OFF" the Juicer and unplug from the power supply. Cle-
very fibrous food- an the juicing sieve according to the instructions in section 'Emp-
stuffs. tying the Containers and Removing Obstacles'. Try to process
fibrous foodstuffs in turn with soft and juicy ingredients.
No juice. The juicing sieve is Switch "OFF" the appliance and unplug from the power supp-
clogged. ly. Clean the juicing sieve (see: 'Emptying the Containers and
Removing Obstacles').
The drip-stop is Turn the stainless steel sleeve at the juice spout by 180° to
closed. open the drip-stop (see: 'Drip-Stop Feature').
The selected speed Select a higher speed level.
is too low.
You are processing Some types of fruit (e.g. mangoes, quinces) will only give off
a type of fruit that there juices when squeezed (see: 'Tips for Juicing').
is not suited for this
kind of juicer.
THE SYSTEMS FOR MIXING AND GRINDING
Problem Reason The Solution
The mixing jug is The threads of the Completely unscrew the blade assembly. Then position the blade
leaking. Water is blade assembly and assembly newly for screwing it onto the glass container. Ensure to
accumulating under mixing jug have mount the blade assembly without tilting the thread to avoid leaka-
the blade assembly. been tilted. ge and damage to the thread (See: 'Assembling the Mixing Jug' or
'Assembling the Grinding System'').
The sealing ring Before turning the blade assembly onto the glass container, ensu-
is missing or not re to place a sealing ring in correct orientation into the groove at
inserted correctly. the inner rim of the blade assembly. The ridged side of the sealing
ring must face upwards (See: 'Assembling the Mixing Jug').
The junction between Try to turn on the blade assembly a little more tightly. Due to
blade assembly and the sealing ring, there is a firm resistance when screwing on the
mixing jug is not scre- blade assembly.
wed on as tight as
necessary.
115