Omron K3HB - MANUAL 2 Manual page 55

List of Settings
Communications Setting Level
Variable Address Parameter
type name
CA 0000 Unit No.
0001 Baud rate
0002 Data length
0003 Stop bit
length
0004 Parity
0005 Send wait
time
Note The values beginning with H' in the Monitor/Setting range column are used when setting or monitoring
data via communications.
Advanced Function Setting Level
Variable Address Parameter
type name
CB 0000 PASS-output
change
0001 Hysteresis
0002 Output OFF
delay
0003 Shot output
0004 Output logic
0005 Output
refresh stop
0006 Tare zero
0007 Zero trim-
ming
0008 Previous
average
value com-
parison
0009 Bank selec-
tion
000A Startup com-
pensation
timer
000B Input error
enable
000C Standby
sequence
000D Cold junction
compensat-
ing circuit
Note (1) The values beginning with H' in the Monitor/Setting range column are used when setting or monitoring
data via communications.
(2) If the event connector is provided as a standard feature or an event connector is added, use EV for
the "bank selection" setting.
2-10
Character Monitor/Setting range
u-no H'00000000 to
H'00000063: (0 to 99)
bps H'00000000: 9.6(0),
H'00000001: 19.2(1),
H'00000002: 38.4(2)
len H'00000000: 7(0),
H'00000001: 8(1)
sbit H'00000000: 1(0),
H'00000001: 2(1)
prty H'00000000: None (0),
H'00000001: Even (1),
H'00000002: Odd (2)
sdwt H'00000000 to
H'00000063 (0 to 99)
Charac- Monitor/Setting range
ter
pass H'00000000: LL(0), H'00000001:
L(1), H'00000002: PASS(2),
H'00000003: H(3), H'00000004:
HH(4), H'00000005: ERR(5)
hys H'00000000 to
H'0000270F: (0 to 9,999)
off-d H'00000000 to
H'000007CF (0 to 1,999)
shot H'00000000 to
H'000007CF (0 to 1,999)
out-n H'00000000: Close in alarm(0),
H'00000001: Open in alarm(1)
o-stp H'00000000: OFF(0), H'00000001:
OUT(1), H'00000002: ALL(2)
t-zr H'00000000: OFF(0)
H'00000001: ON(1)
z-trm H'00000000: OFF(0)
H'00000001: ON(1)
hp-f H'00000000: OFF(0)
H'00000001: ON(1)
bnk-c H'00000000: OFF(0), H'00000001:
KEY(1), H'00000002: EV(2)
s-tmr H'00000000 to
H'0000270F: (0 to 99.9)
s.err H'00000000: Disable(0),
H'00000001: overflow(1),
H'00000002: input error(2)
stdby H'00000000: OFF(0)
H'00000001: ON(1)
cjc H'00000000: OFF(0)
H'00000001: ON(1)
Character Default Decimal
setting point
0 to 99 1
---
9 . 6, 19 . 2, 9 . 6
---
38 . 4
7, 8 7
---
1, 2 2
---
none, even, even
---
odd
0 to 99 20
---
Character Default Decimal
setting
ll, l, pass, pass
---
h, hh, err
0 to 9999 1 According to
the decimal
position set-
ting
0 to 1999 0
---
0 to 1999 0 ---
n-o, n-c n-o
---
off, out, all off
---
off, on off
---
off, on off ---
off, on off ---
off, key, ev off
---
(See note.)
0 . 0 to 99 . 9 0 . 0
1
off, over, s.err ---
s.err
off, on off
---
off, on on
---
Section 2
Unit Model
X V S H
---
kbps
bit
bit
---
ms
Unit Model
point
X V S H
---
---
S: ms
Others:
100 ms
S: ms
Others:
100 ms
---
---
--- x
--- x
---
---
s
---
---
--- x x x