Table of Contents
Advertisement
Using Effects
4. Make Chain settings.
If the Chain check box is checked, the insert effect will
be connected in series. Since the output of the oscillator is
being sent to IFX1 in step 2, making settings as shown in
the diagram step 6 would connect all five insertion effects
IFX1 → IFX2 → IFX3 → IFX4 → IFX5 in series, so that
these effects would be inserted into the output of the
oscillator.
5. Make settings for Pan (CC#8), Bus Sel. (Bus Select),
Send 1, Send 2, REC Bus and Ctrl Bus for the sound
after it has passed through the insert effects.
If you've specified a chain, the settings that follow the
last IFX in the chain will be valid (except for "Ctrl Bus").
Pan: Sets the pan of the IFX output.
Bus Sel. (Bus Select): Specifies the output destination.
Normally you will set this to L/R. If you wish to send the
sound that has passed through the insert effects to Audio
Outputs (individual) 1–4, select 1–4, 1/2, or 3/4.
Send 1, Send 2: Sets the send levels to the master effects.
For this example, set this to 127.
Ctrl Bus: The FX Control Buses lets you create effects
"sidechains." Sidechains let you control an effect with
one audio signal (the sidechain), while the effect
processes a completely different audio signal. This is
convenient for use with vocoders, compressors and
limiters, gates, etc. For more information, see "FX
Control Buses" on page 737 of the PG.
REC Bus: The sound processed by the insert effect will
be sent to the REC bus. In the Sampling page, you can set
the Sampling Setup Source Bus to a REC bus, and
sample the signal that is sent to the REC bus. Use this if
you want to sample only the sound of an audio input
source being processed by an insert effect (and not
sample the sound of the oscillator output). Alternatively,
the direct sound from the audio inputs can be mixed with
the sound processed by an insert effect, sent to a REC
bus, and sampled.
6. Go to the IFX– Insert FX page, and edit the
parameters of the insert effect you selected.
Press the IFX 1–12 tab, use the tabs at the left to select
IFX1–12, and edit the effect parameters.
Effect On/Off: Turns the insert effect on/off. This is
linked with the on/off setting in the Insert FX page.
P (Effect Preset): Selects an effect preset. The
NAUTILUS' internal memory contains "effect presets"
which are parameter settings for each effect from 001:
St.Dyna Compressor through 197: Rotary Speaker Pro
CX Custom.
Effect parameters you edit are saved as part of each
program, but effect presets allow you to save favorite
parameter settings for each effect. For more information,
see "Effect Presets" on page 232.
224
Effect On/Off
Wet/Dry
Effect Parameters
For details on the individual effects, see:
• "Dynamics" on page 765 of the PG
• "EQ and Filters" on page 778 of the PG
• "Overdrive, Amp models, and Mic models" on page 794
of the PG
• "Chorus, Flanger, and Phaser" on page 803 of the PG
• "Modulation and Pitch Shift" on page 816 of the PG
• "Delay" on page 837 of the PG
• "Reverb and Early Reflections" on page 859 of the PG
• "Mono-Mono Serial" on page 864 of the PG
• "Mono/Mono Parallel" on page 880 of the PG
• "Vintage" on page 895 of the PG
Master effects
The input levels to the master effects are set by the Send 1 &
2 levels. If Send 1 & 2 are zero, the master effects will not
be heard. Send 1 goes to MFX1, and Send 2 goes to MFX2.
1. Go to the PROGRAM > MFX/TFX– Routing page.
2. In MFX1 and MFX2, select the type of each master
effect.
The procedure is the same as when selecting an insert
effect. (See step 2 of "Insert effects" on page 223.)
3. Press the On/Off button to turn on the master effect.
Each time you press the button, the master effect will be
switched on/off. When Off, the output of the master effect
will be muted.
P (Effect preset)
Advertisement
Table of Contents
