Related Manuals for Delta DIJITAL PROJECTION M-Vision 21000 II WUXGA Series
Summary of Contents for Delta DIJITAL PROJECTION M-Vision 21000 II WUXGA Series
- Page 1 M-Vision 21000 II Series WUXGA M-Vision 24000 Series WUXGA M-Vision 27000 Series WUXGA IMPORTANT INFORMATION Rev A December 2023 123-895A...
- Page 2 M-Vision 2X000 Series WUXGA This page is intentionally left blank Rev A December 2023 Important Information page 2 Digital Projection Ltd.
-
Page 3: Introduction
Introduction M-Vision 2X000 Series WUXGA Introduction Congratulations on your purchase of this Digital Projection product. The information in this document is relevant for the following products: M-Vision 21000 II Series WUXGA (EMEA and China) M-Vision 21000 II Series WUXGA (USA TAA compliant) M-Vision 21000 II Series WUXGA (USA TAA compliant - REF) M-Vision 24000 Series WUXGA (EMEA and China) M-Vision 24000 Series WUXGA (USA TAA compliant) -
Page 4: Additional Documentation
M-Vision 2X000 Series WUXGA Introduction Additional Documentation Full information about operating, connecting and setting up the projector can be found in the User Guides. Please use the QR code (also located on the projector) to access the latest M-Vision projector user guides and other documentation via the Digital Projection website. -
Page 5: Table Of Contents
Contents M-Vision 2X000 Series WUXGA Contents Introduction Symbols used in this document Additional Documentation Legal notice Third Party Credits Contents What's in the box? Electrical and Physical Specifications General Precautions Laser Safety Precautions Laser Risk Group 2 Precautions Laser Risk Group 3 Precautions Laser Parameters Light Output Laser Power... - Page 6 M-Vision 2X000 Series WUXGA Contents Fitting a lens Inserting a new lens Removing the lens Positioning the screen and projector Stacking Pin and cup stacking Signal connections Control connections AC Power Precautions Connecting the power supply Basic Operating Instructions Switching the projector on Switching the projector off Interlock reset Selecting an input signal...
-
Page 7: What's In The Box
What's in the box? M-Vision 2X000 Series WUXGA What's in the box? Batteries Remote Control (2xAAA) Important Projector Information Book Power Cable, UK Power Cable, Europe Power Cable, China NEMA 5-15P - C19 Power NEMA 6-15P - C19 Power Cable, North America Cable, North America Remote Control Cable HDMI Cable... -
Page 8: Electrical And Physical Specifications
M-Vision 2X000 Series WUXGA Electrical and Physical Specifications Electrical and Physical Specifications M-Vision 21000 II Series M-Vision 24000 Series WUXGA WUXGA Mains Voltage 200-240 VAC 10.6 A 50/60Hz 110-130 VAC 11.1 A 50/60Hz Operating Temperature 0°C to 40°C (32°F to 104°F) in mormal mode. 33°C to 40°C (91°F to 104°F) automatically reduced to ECO mode light output Storage Temperature... - Page 9 Electrical and Physical Specifications M-Vision 2X000 Series WUXGA M-Vision 21000 II Series M-Vision 24000 Series WUXGA WUXGA Fan Noise typical 44dBA, max 46dBA in typical 47dBA, max 49dBA in Normal mode Normal mode typical 42dBA, max 44dBA in typical 45dBA, max 47dBA in ECO mode ECO mode M-Vision 27000 Series WUXGA...
- Page 10 M-Vision 2X000 Series WUXGA Electrical and Physical Specifications Specifications are subject to change without notice. Rev A December 2023 Important Information page 10 Digital Projection Ltd.
-
Page 11: General Precautions
General Precautions M-Vision 2X000 Series WUXGA General Precautions Warning! Death or Serious Injury could occur if the following precautions are ignored Eye Hazard! Do not look directly into the lens when the light source is on. The high brightness can cause permanent eye damage Fire Hazard! Keep any combustible material away from hot surfaces and the projected beam. - Page 12 M-Vision 2X000 Series WUXGA General Precautions Ensure that the power outlet includes a Ground connection, as this equipment MUST be earthed. Take care to prevent small objects such as paper or wire from falling into the projector. If this does happen, switch off immediately, and have the objects removed by authorized service personnel.
-
Page 13: Laser Safety Precautions
Laser Safety Precautions M-Vision 2X000 Series WUXGA Laser Safety Precautions Warning! Death or Serious Injury could occur if the following precautions are ignored Permanent/Temporary Blindness Hazard Do not look directly into the lens when the light source is on. The high brightness can cause permanent eye damage. -
Page 14: Laser Risk Group 3 Precautions
M-Vision 2X000 Series WUXGA Laser Safety Precautions Avoid the use of optical aids, such as binoculars or telescopes, inside the beam. MOUNT ABOVE THE HEAD HEIGHT OF CHILDREN. It is recommended to use a ceiling mount to place this product above the eyes of children. Laser Risk Group 3 Precautions Not for household use. -
Page 15: Laser Parameters
Laser Safety Precautions M-Vision 2X000 Series WUXGA Laser Parameters Wavelength (Red) 635-651 nm Wavelength (Blue) 449-461 nm Mode of operation Pulsed, due to frame rate Pulse duration (Red) 1.00 ms Pulse duration (Blue) 0.76 ms Pulse repetition rate 180 Hz Maximum pulse energy (Red) 0.26 mJ Maximum pulse energy (Blue) -
Page 16: Compliance With International Standards
M-Vision 2X000 Series WUXGA Compliance with International Standards Compliance with International Standards RF Interference The Federal Communications Commission does not allow any modifications or changes to the unit EXCEPT those specified by Digital Projection in this manual. Failure to comply with this government regulation could void your right to operate this equipment. -
Page 17: Product Labels
Product Labels M-Vision 2X000 Series WUXGA Product Labels Projector M-Vision 21000 II Series WUXGA Manufacturers ID Label (EMEA and China) Rev A December 2023 Important Information page 17 Digital Projection Ltd. - Page 18 M-Vision 2X000 Series WUXGA Product Labels M-Vision 21000 II Series WUXGA Manufacturers ID Label (USA TAA compliant) Rev A December 2023 Important Information page 18 Digital Projection Ltd.
- Page 19 Product Labels M-Vision 2X000 Series WUXGA M-Vision 24000 Series WUXGA Manufacturers ID Label (EMEA and China) Rev A December 2023 Important Information page 19 Digital Projection Ltd.
- Page 20 M-Vision 2X000 Series WUXGA Product Labels M-Vision 24000 Series WUXGA Manufacturers ID Label (USA TAA compliant) Rev A December 2023 Important Information page 20 Digital Projection Ltd.
- Page 21 Product Labels M-Vision 2X000 Series WUXGA M-Vision 27000 Series WUXGA Manufacturers ID Label (EMEA and China) Rev A December 2023 Important Information page 21 Digital Projection Ltd.
- Page 22 M-Vision 2X000 Series WUXGA Product Labels M-Vision 27000 Series WUXGA Manufacturers ID Label (USA TAA compliant) Rev A December 2023 Important Information page 22 Digital Projection Ltd.
-
Page 23: Label Locations
A/S 센터 : +82 2 515 5303 모델명 : M-Vision 27000 XX R41086 RoHS 製造地:中國 / 制造地:中国 / Made in China Delta Electronics (Jiangsu) Ltd. No.1688, Jiangxing East Rd., Wujiang Economic and Technological Development Zone, XXXXX Suzhou City, Jiangsu Province, P.R.C.215200 3264675900 制造商... -
Page 24: Projector - Ref Model
M-Vision 2X000 Series WUXGA Product Labels Projector - REF Model M-Vision 21000 II Series WUXGA Manufacturers ID Label (USA TAA compliant - REF) Rev A December 2023 Important Information page 24 Digital Projection Ltd. - Page 25 Product Labels M-Vision 2X000 Series WUXGA M-Vision 21000 II Series WUXGA Manufacturers ID Label (USA TAA compliant - REF) Rev A December 2023 Important Information page 25 Digital Projection Ltd.
- Page 26 M-Vision 2X000 Series WUXGA Product Labels M-Vision 21000 II Series WUXGA Manufacturers ID Label (USA TAA compliant - REF) Rev A December 2023 Important Information page 26 Digital Projection Ltd.
-
Page 27: Label Locations - Ref Model
A/S 센터 : +82 2 515 5303 모델명 : M-Vision 27000 XX R41086 RoHS 製造地:中國 / 制造地:中国 / Made in China Delta Electronics (Jiangsu) Ltd. No.1688, Jiangxing East Rd., Wujiang Economic and Technological Development Zone, XXXXX Suzhou City, Jiangsu Province, P.R.C.215200 3264675900 制造商... -
Page 28: Location Of Laser Aperture
M-Vision 2X000 Series WUXGA Location of Laser Aperture Location of Laser Aperture 1. The laser aperture is located as indicated below. Do not look directly at the light coming from the lens. Rev A December 2023 Important Information page 28 Digital Projection Ltd. -
Page 29: Interlock Switches
Interlock Switches M-Vision 2X000 Series WUXGA Interlock Switches Interlock switches are installed inside the projector. These will power-off the system when activated. 1. Will be activated when the projection lens is removed or misplaced. 2. Will be activated when the top cover is removed. -
Page 30: Installation Precautions
M-Vision 2X000 Series WUXGA Installation Precautions Installation Precautions The projector must be installed only by suitably qualified personnel, in accordance with local building codes. The projector is heavy. Use safe handling techniques when lifting the projector. Do not drop or knock the projector. Do not install the projector close to anything that might be affected by its operational heat, for instance, polystyrene ceiling tiles, curtains etc. - Page 31 Installation Precautions M-Vision 2X000 Series WUXGA When using projectors in environments with third party high power laser systems avoid direct laser beams pointing towards the projection lens. This may cause incident light to converge into the optical engine and cause damage to the DLP™...
- Page 32 M-Vision 2X000 Series WUXGA Installation Precautions The following positions are to be avoided as they can reduce motor life: Lens facing down Inputs and outputs facing up Allow at least 50cm (19.7in) of space between the ventilation outlets and any wall, and 30cm (11.8in) on all other sides. Minimum 500mm Minimum 500mm Minimum 500mm...
- Page 33 Installation Precautions M-Vision 2X000 Series WUXGA Make sure the lens cap is removed from the lens before operating the projector. Light energy levels have been known to cause damage to both the lens and projector optics. This damage is not covered by our warranty. Make sure the lens cap is removed from the rear of the lens before it is inserted into the projector.
-
Page 34: Laser Hazard Installation Precautions
M-Vision 2X000 Series WUXGA Laser Hazard Installation Precautions Laser Hazard Installation Precautions Do not attempt to access the internal hardware of the projector. Do not a attempt to modify or remove the laser module. Do not operate the projector without its protective covers. Please consult with a qualified professional to install or remove the lens. -
Page 35: Light Hazard Warning
Laser Hazard Installation Precautions M-Vision 2X000 Series WUXGA Light Hazard Warning No direct exposure to the beam is permitted, RG3 BS EN IEC 62471-5:2015. Light Hazard Distance and Hazard Zone Hazard Distances for Laser Risk Group 3 variants. Operators should control access to the beam within the hazard distance or install the projector at sufficient height to prevent exposures of spectators’... -
Page 36: Restriction Zone
M-Vision 2X000 Series WUXGA Laser Hazard Installation Precautions Restriction Zone A restriction zone should be in place around the hazard zone to prevent any person from entering the hazard zone with any part of their body: Horizontal clearance . This should be no less than 2.5m around the hazard zone Vertical clearance... -
Page 37: Fitting A Lens
Fitting a lens M-Vision 2X000 Series WUXGA Fitting a lens The projector must be fully turned off prior to attempting a lens change. When changing the lens, avoid using excessive force as this may damage the equipment. Avoid touching the surface of the lens as this may result in image impairment. -
Page 38: Inserting A New Lens
M-Vision 2X000 Series WUXGA Fitting a lens Inserting a new lens 1. Remove the front and rear lens caps 2. Insert the lens with the connector in upright position. 3. Rotate the lens clockwise until it clicks into place. Rev A December 2023 Important Information page 38 Digital Projection Ltd. -
Page 39: Removing The Lens
Fitting a lens M-Vision 2X000 Series WUXGA Removing the lens 1. Push the lens release button all the way in 2. Turn the lens anti-clockwise until it disengages 3. Slowly remove the lens 4. Fit lens caps to the front and rear of the lens 5. -
Page 40: Positioning The Screen And Projector
M-Vision 2X000 Series WUXGA Positioning the screen and projector Positioning the screen and projector 1. Install the screen, ensuring that it is in the best position for viewing by your audience. 2. Mount the projector, ensuring that it is at a suitable distance from the screen for the image to fill the screen. -
Page 41: Stacking
Stacking M-Vision 2X000 Series WUXGA Stacking The projectors must be in a vertical position when they are stacked. This will ensure that the stresses are distributed to all four corners of the chassis. Do not use the threaded holes for the adjustable feet to hang or mount the projector. - Page 42 M-Vision 2X000 Series WUXGA Stacking 2. Insert and secure the stacking tops in place of the removed screws. 3. Mount the top projector onto the bottom projector. Ensure that all four pins are placed into the cups on the bottom projector.
- Page 43 Stacking M-Vision 2X000 Series WUXGA 4. Use the stacking safety pins to secure each connection. Rev A December 2023 Important Information page 43 Digital Projection Ltd.
-
Page 44: Signal Connections
M-Vision 2X000 Series WUXGA Signal connections Signal connections 1. Sync In 3D sync input signal. Use a BNC connector to connect the 3D sync from your graphics card or server. 2. Sync Out 3D sync output signal. This enables synchronized 3D with multiple projectors. Use a 3-pin DIN connector to connect this to another projector. -
Page 45: Control Connections
Control connections M-Vision 2X000 Series WUXGA Control connections 1. Trigger The trigger output can be used to control an electrically operated screen. The screen will be automatically deployed when the projector starts up and retracted when the projector shuts down. 2. -
Page 46: Ac Power Precautions
M-Vision 2X000 Series WUXGA AC Power Precautions AC Power Precautions Warning! Death or Serious Injury could occur if the following precautions are ignored Shock Hazard! Only use the AC power cord provided or recommended by the manufacturer Fire & Shock Hazard! Do not operate the product unless the power cord, socket and plug meet local rating standards Do not attempt operation if the AC supply is not within the specified parameters... -
Page 47: Basic Operating Instructions
Basic Operating Instructions M-Vision 2X000 Series WUXGA Basic Operating Instructions See Control panel on page 51 for guidance on using the control panel to control the projector. See Remote control on page 54 for guidance on using the remote control to control the projector. Switching the projector on 1. -
Page 48: Selecting An Input Signal
M-Vision 2X000 Series WUXGA Basic Operating Instructions Selecting an input signal 1. Connect one or more image sources to the projector. 2. Select the input you want to display: Press one of the input buttons on the remote control or control panel. Alternatively, open the On-screen display (OSD) by pressing MENU. -
Page 49: Adjusting The Lens
Basic Operating Instructions M-Vision 2X000 Series WUXGA Adjusting the lens You can use the following options to adjust the lens: Control panel. See Control panel on page 51 Remote control. See Remote control on page 54 On screen display (OSD). OSD Lens menu The Lens menu provides access to the Lens Control setting and the Lens Center command. -
Page 50: Operating The Projector
M-Vision 2X000 Series WUXGA Operating the projector Operating the projector The projector has the following controls: Remote control Control panel Do not make changes to the networking configuration unless you understand what you are doing, or have taken advice from your Network Manager. If you make a mistake, it is possible that you will lose contact with the projector. -
Page 51: Control Panel
Operating the projector M-Vision 2X000 Series WUXGA Control panel 1. POWER Switches the projector on and off (STANDBY). 2. SYNC Press to resynchronise the active input. 3. Arrow buttons & ENTER Press Focus , Lens Shift or Zoom and use the Up and Down arrow buttons to adjust the lens focus, shift or zoom. - Page 52 M-Vision 2X000 Series WUXGA Operating the projector 10. EXIT Exits the current OSD page and enters the level above. Exits the OSD when at the top level OSD page. 11. INFO Press and hold for 5 seconds to activate or deactivate the LCM.
-
Page 53: Projector Indicators
Operating the projector M-Vision 2X000 Series WUXGA Projector indicators 1. LCM Displays information about the current state of the projector. 2. TEMP Off = no error Flashing red = temperature error 3. POWER Off = the projector is switched Flashing green = the projector is warming up Flashing amber = the projector is cooling down... -
Page 54: Remote Control
M-Vision 2X000 Series WUXGA Operating the projector Remote control 1. Power ON / OFF Turns power on and off. 2. Pic Mute OPEN / CLOSE Press CLOSE to hide the Pic Mute projected image. There are OPEN CLOSE two PIC Mute settings: Laser. - Page 55 Operating the projector M-Vision 2X000 Series WUXGA 9. FREEZE Freeze the current frame. 10. LENS adjustment FOCUS IN / OUT: adjust Pic Mute OPEN CLOSE focus. SHIFT: press and hold this button, then use the OK and MENU DEFAULT Navigation buttons. Press OK to switch between Shift Adjustment and Zoom / Focus Adjustment.
- Page 56 M-Vision 2X000 Series WUXGA Operating the projector 17. DISPLAYPORT 1 / R / numeric input 4 Select DisplayPort 1 input. 18. HD-T / G / numeric input 5 Pic Mute Select the HDBaseT input. OPEN CLOSE 19. ADDR / ALL (with red indicator at the top) MENU DEFAULT...
- Page 57 Operating the projector M-Vision 2X000 Series WUXGA 21. VGA / 3D / numeric input 7 There is no VGA input on this projector. Use with ALT to toggle the 3D Pic Mute Format setting between Off OPEN CLOSE and Auto. 22.
-
Page 58: Contact Information
M-Vision 2X000 Series WUXGA Contact Information Contact Information China North America Europe Digital Projection China Digital Projection Inc. Digital Projection Limited 中 国 北 京 市 朝 阳 区 芍 药 居 55 Chastain Road, Suite 115, Unit 3, Broadgate, Oldham 北...