Table of Contents
Advertisement
Checking the entered edit points with the edit lamps
You can make sure all the edit points necessary for the edit have been entered with the edit point lamps. Note that these lamps will
light up as explained below depending on the procedure followed.
BASIC EDITING WITH ONE CUT
Ci) When the P1 VTRis the source, this lamp will light up after
the edit IN point has been entered on this VTR.
© When the P2 VTR is the source, this lamp will light
up after
the edit IN point has been entered on this VTR.
3) When the P1 VTR is the source, this lamp will light up after
the edit OUT point has been entered on this VTR.
A/B ROLL EDITING
oe When the P2 VTR is the source, this lamp will light up after
the edit OUT point has been entered on this VTR.
© This lamp will light up after the edit IN point has been
entered on the recorder VTR side.
© This tamp will light up after the edit OUT point has been
entered on the recorder VTR side.
.
Ifthe A roltis on the Pt VTR, this lamp will light up after the
edit IN point is on the A roll.
If the A roll is on the P2 VTR, this lamp will ight up after the
edit IN point is entered on the A roll.
Ifthe B rollis on the P1 VTR, this lamp will light up after the
edit IN point is entered on the B roll.
Ifthe Broltis on the P2 VTR, this lamp will light up after the
edit IN point is entered on the B roll.
o 6 8 8 8
Ifthe A roll is on the P1 VTR, this lamp will light up after the
edit OUT point is entered on the A roll.
-57-
a
RY
EN ET
6
Ifthe A roillis on the P2 VTR, this lamp will light up after the
edit OUT point is entered on the A roil.
@
iftheB roltis on the P1 VTR, this lamp will light up after the
edit OUT point is entered on the B roll.
(3) If the B rottis on the P2 VTR, this lamp will light up after the
edit OUT point is entered on the B roll.
(9) This lamp will light up after the edit IN point is entered on
the recorder VTR side.
@ This amp will tight up after the edit OUT point is entered
on the recorder VTR side.
aed
ae oe
on
EDITING WITH THE AUXILIARY EQUIPMENT
*These lamps function ass explained in the previous page.
@
If the auxiliary equipment is used, this lam p will ight up and the P1 or P2 lamp on the left side will function as the edit lamps of the
auxiliary equipment.
The upper AUX lamp lights up when normal editing is performed.
Refer to the following notes when perfor ming A/B roll editing.
Notes
If the edit points are entered on the auxiliary equipment (the A roll is on the AUX) during A/B roll editing, the upper (P1) AUX lamp
will light up (see figure below).
elf the B roll is on the P2 VTR, the upper AUX lamp will remain fit.
*if the B rollis on the AUX, the lower AUX lamp will light up in case the A roil is on the P@ VTR, and the upper AUX lamp will light up
in case the B roll is on the P2 VTR.
Refer to page 36.
AUDIO SPLIT EDITING
®The lamps in this mode function in the similar way as in other
editing modes.
e
Hf the P1 VTR audio IN point is entered the lamp will light
4) If the P2 VTR audio OUT pointis entered the lamp will light
up.
up.
e
if the P2 VTR audio IN point is entered the lamp will light
C5] This lamp will light up after the audio IN point has been
up.
entered on the recorder VTR side.
© This lamp wit! light up after the audio OUT point has been
© ifthe P1 VTR audio OUT pointis entered the tamp will light
entered on the recorder VTR side.
up.
.
Refer to page 37.
~58-
Advertisement
Table of Contents
