Table of Contents
Advertisement
Initial Editing
When executing an edit on a blank tape on which no reference signal (black burst) has been recorded or on the pre-recorded tape,
the reference signal is necessary to pertorm the edit
if the AG-SW800 is not connected, input the composite signal (black burst signal, etc.) to the input terminal of the recorder side VTR.
38 89 89 eB
@
Press the EVENT key.
@
Press the EDIT key to record the reference signal on the
preroll portion of the tape. The EDIT lamp will light up.
©Press the EDIT key while holding down the AUTO
key to
execute assemble editing after entering event number
0000. The AUTO and EDIT lamps will tight up.
© Press the ENTER key.
- <initial Edit Function> -
paca Teng
Esting
mL
—
GO) - com
2
Eanng stares
Moe
Ponto
Operation
on tre }—~—
Operation
on
ttre}
4
RECORDER storm
RECORDER stare
our
+21
neconcte
fo
2 peverndte —of
}+-—_—— 21 seconds —————-+fo—
2 seconds ~oj
'The raterence (Mack Burst shgnal i recorded
'The raterence (Steck Burs!) signal is recorded
*After the end of the initial edit the tape will stop at the IN
*After the end of the initial edit the edit of the first event will
point of the initial event.
start.
'lt is possible to rewind the tape to the beginning at initial edit even from the middie of the tape.
«| edit data is recorded on the tape, the tape is rewound to the beginning and the time code display shows a value 23 seconds
less than the first event RECORDER
IN point.
*!f edit data is not recorded on the tape, the tape is sewound to the beginning and the time code display reads "00:00:00:00".
—_ 40 —
Basic Editing Operation
You can perform the different kinds of editing operation, including the manual, A/B roll, sync-roll editing and the edit using the Edit
keys with this controller. The procedures for basic editing are described below. Follow them when making edits.
1. Editing Operation Selection
Press the ASSEM
key to record
Press any of the keys desired in
the video and audio signals. The
the insert editing mode.
corresponding lamp will light up.
Press the key again to cancel
the mode selected.
@ Assemble editing
"Assemble editing" permits the user
to add program m aterial to
the end of a previously recorded portion, thus making one
continuous,
uninterrupted
program
from many
segments.
Video/Hi-Fi Sound (CH1/CH2) and Normal Audio CH1 and
CH2 or Time Code are all edited at the same time. As Shown in
the itlustration, suppose
that part £¥ had been previously
recorded. To this, a new program fq is added. This results ina
new program consisting of £§ and Ey.
®Video and Hi-Fi Sound cannot be separated during editing.
Hi-Fi sound will be erased with the Video signal.
©The noise may appear on the IN point with Hi-Fi Sound.
Direction
of tape movement
Normal Audio CH2 track
Normal Audio CH! track
Normal Audio CH2 track
Normat Audio CHt track
PLAYER
video'-Fi Sound track
Controt track
End point for assemble editing
Beginning pot for assembie editing
sg
Normat Audio CH2 track
Normat Audio CH1 track
EDITED
Video/Hi-Fr Sournd track
@ Insert editing
"Insert
editing"
permits the user to add
program
material
somewhere in the middle of a previously recorded portion. As
shownin
the illustration, the new program material {J is added
between parts of the already-recorded material EJ. The result is
anew p rogram consisting of parts EJ, EY. E§. For insert editing it
is possible
to insert only Video/Hi-Fi
Sound
(CH1/CH2),
Normal Audio CH1, Normal Audio CH2 (or Time Code), or any
combin ation of these,
Note:
If the
AUDIO CH2 SELECT Switch on a VHS or S-VHS VTR
that is used for editing is set to "TIME CODE", the A2 key will
allow recording of the TC signal for channel 2.
The nwise may appear on the IN and OUT point with Hi-Fi
Sound.
Direction of tape movernent
Normal Audio CH2 track
Normat Audio CHI track
Vicieo/Hi-Fi Sound track
Control track
Normal Audio CH2 track
Normal Audio CHI track
Vudieo/H)-Fi Sound track
Control track
Normal Audio CH2 track
Normal Audio CHI track
Vicdea/Ht-Fi Sound track
Camntro! track (not erased on any mode}
'The figure shows inser! editing for Videu'Hi-F: Sound and Normat Audio CH2.
i Editing mode button operation
selected.
insert to assemble (or assemble to insert).
*The insert-editing mode is established when moving from ASSEMBLE to the V A1, A2 or TC buttons.
The assemble-editing mode is established when moving from V, A1, A2 or TC to the ASSEMBLE button.
When At (V, A2 or TC) is pressed twice during ins ert-editing, the A1 (V, A2 or TC) lamp goes off, indicating this mode is not
*During insert-editing, insert editing mode (V, A1, A2 and TC) can be cha nged but the editing mode cannot be changed from
When the editing mode is not selected, the editing mode lamp will flash to draw attention to the editing mode setting.
Advertisement
Table of Contents
