Table of Contents
Advertisement
[COMMAND]
[POWER ON]
[STANDBY]
[QUICK STARTUP]
[SHUTTER]
[INPUT]
[OPERATING MODE]
*1 This item can be selected when the optional 12G-SDI Terminal Board (Model No.: TY-SB01QS) is installed in <SLOT>.
*2 This item can be selected when the optional Function Board for 12G-SDI Optical (Model No.: TY-SB01FB) is installed in <SLOT>.
*3 This item can be selected when the optional DIGITAL LINK Terminal Board (Model No.: TY-SB01DL) is installed in <SLOT>.
*4 This item can be selected when the optional Wireless Presentation System Receiver Board (Model No.: TY-SB01WP) is installed in <SLOT>.
*5 This item can be selected when the Function Board by other manufacturers is installed in <SLOT>.
*6 When the optional DIGITAL LINK output supported device (Model No.: ET-YFB100G, ET-YFB200G) is connected to the <DIGITAL LINK IN/
LAN> terminal of the optional DIGITAL LINK Terminal Board (Model No.: TY-SB01DL) installed in <SLOT>, its input name is automatically
reflected from [INPUT1] to [INPUT10]. When an item that does not reflect the input name is selected, it will be disabled.
*7 If you change the settings while using the projector, the duration until the luminance decreases by half may shorten or the luminance may
decrease.
11) Press the <ENTER> button.
f The command is fixed and n is displayed at the left of the selected command.
f After the command is fixed, press the <MENU> button to close the detailed setting screen.
12) Press asqw to select [STORE], and press the <ENTER> button.
Note
f To delete a command that has been already set, press the <DEFAULT> button on the remote control while the screen in Step 5) is
displayed, or select [DELETE] at the screen in Step 6) and press the <ENTER> button.
f If multiple commands have been set for the same time, they are executed in chronological order starting from the smallest command
number.
f The operating time will be the local time. (x page 175)
f If an operation is executed with the remote control or control panel of the projector or with a control command before the command set in
[SCHEDULE] is executed, the command set with the schedule function may not be executed.
[MULTI PROJECTOR SYNC]
Set the contrast synchronization function and the shutter synchronization function.
The contrast synchronization function is a function to display a combined screen with a balanced contrast by
sharing the brightness level of the image signal input to each projector when a multi-display is constructed
by combining the projected image of multiple projectors. The shutter synchronization function is a function to
synchronize the shutter operation of the specified projector to other projectors, and the effect using the shutter
function including the fade in/fade out operation can be synchronized.
Chapter 4 Settings — [PROJECTOR SETUP] menu
Detailed settings of
[COMMAND]
―
―
[ON]
[OFF]
[OPEN]
[CLOSE]
[HDMI1]
[HDMI2]
[DisplayPort]
[SDI [SLOT]]
*1
[SDI OPT1 [SLOT]]
[SDI OPT2 [SLOT]]
[DIGITAL LINK [SLOT]]
[PressIT [SLOT]]
[SLOT]
*5
[INPUT1] - [INPUT10]
[NORMAL]
[ECO]
[QUIET]
*7
[USER1]
[USER2]
[USER3]
Switches on the projector.
Enters standby.
Enables the function of the [PROJECTOR SETUP] menu →
[QUICK STARTUP].
Disables the function of the [PROJECTOR SETUP] menu →
[QUICK STARTUP].
Disables the shutter function (shutter: opened).
Enables the shutter function (shutter: closed).
Switches the input to HDMI1.
Switches the input to HDMI2.
Switches the input to DisplayPort.
Switches the input to SDI.
Switches the input to SDI OPT1.
*2
Switches the input to SDI OPT2.
*2
Switches the input to DIGITAL LINK.
*3
Switches the input to PressIT.
*4
Switches the input to SLOT.
Switches the input to DIGITAL LINK, and switches the input of the
*6
DIGITAL LINK output supported device to the specified input.
Prioritizes brightness.
Prioritizes the life of the light source.
Prioritizes the operation with low noise.
Controls the power with the setting set to [USER1].
Controls the power with the setting set to [USER2].
Controls the power with the setting set to [USER3].
Description
ENGLISH - 177
Advertisement
Table of Contents
