Table of Contents
Advertisement
Setting item
[CONTRAST MODE]
(Correction mode setting)
[AUTO CONTRAST]
(Automatic light source
adjustment)
[BRILLIANT CORRECTION]
(Adjustment of aperture
diaphragm control)
[BRIGHT SIGNAL LEVEL]
(Setting of the brightness level
of the signal to start the light
adjustment)
[LIGHTS OUT TIMER]
(Time setting until the light turns
off)
[LIGHTS OUT SIGNAL
LEVEL]
(Setting of the brightness level
of the signal to turn off the light)
[LIGHTS OUT FADE-IN]
(Setting of fade-in when lighting
up again)
[LIGHTS OUT FADE-OUT]
(Setting of fade-out when
lighting off)
[MANUAL INTENSITY]
(Manual light source
adjustment)
[DYNAMIC GAMMA]
(Adjustment of signal
compensation)
[MULTI PROJECTOR SYNC]
Chapter 4 Settings — [PICTURE] menu
Select this item when misadjusted black level (grayish black) is
bothersome in the dark scenes.
[1]
Performs conventional correction to adjust the black level by
decreasing the general brightness.
Select this item when topical radiance is required even in dark
scenes.
[2]
Performs standard correction of the projector that does not
decrease the brightness too much.
(Factory default setting)
[OFF]
Does not adjust the light source.
The higher the value, the stronger the light adjustment of the light
[1] - [255]
source.
Can be set in increments of 1.
[OFF]
Does not correct brightness even in a scene with radiance.
[1]
Slightly corrects brightness in a scene with radiance.
Moderately corrects brightness in a scene with radiance.
[2]
(Factory default setting)
Strongly corrects brightness in a scene with radiance. This setting
[3]
will maximize the brightness.
Adjusts the light source when the brightness level of the image
signal being input gets lower than the set value. The higher the
[6%] - [50%]
value, the larger the range to perform the light adjustment of the
light source.
Can be set in increments of 1 %. (Factory setting: 30 %)
[DISABLE]
Does not turn off the light source.
Turns off the light source when the brightness level of the image
signal being input goes under the value set in [LIGHTS OUT
[0.0s] - [10.0s]
SIGNAL LEVEL].
Select an item from [0.0s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.0s] -
[4.0s] can be selected in increments of 0.5.
Set the level of the brightness of the image signal to turn off the light
[0%] - [5%]
source with [LIGHTS OUT TIMER].
Can be set in increments of 1 %. (Factory setting: 0 %)
Does not set the fade-in of the image when the light source is
[OFF]
turned on again from the condition that the light source was turned
off with [LIGHTS OUT TIMER].
Sets the time to fade in the image when the light source is turned
on again from the condition that the light source was turned off with
[0.5s] - [10.0s]
[LIGHTS OUT TIMER].
Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] -
[4.0s] can be selected in increments of 0.5.
Does not set the fade-out of the image when the light source is
[OFF]
turned off with [LIGHTS OUT TIMER].
Sets the time to fade out the image when the light source is turned
off with [LIGHTS OUT TIMER].
[0.5s] - [10.0s]
Select an item from [0.5s] - [4.0s], [5.0s], [7.0s], or [10.0s]. [0.5s] -
[4.0s] can be selected in increments of 0.5.
The larger the value, the stronger the correction.
[0] - [255]
Can be set in increments of 1. (Factory setting: 255)
[OFF]
Does not compensate the signal.
[1]
Slightly compensates the signal.
[2]
Moderately compensates the signal.
Strongly compensates the signal. This setting will maximize the
[3]
contrast.
Sets the contrast synchronization function.
This setting item is common with the following menu item.
f The [PROJECTOR SETUP] menu → [MULTI PROJECTOR
Refer to the [PROJECTOR SETUP] menu → [MULTI PROJECTOR
SYNC] (x page 177) for details.
Details
SYNC]
ENGLISH - 105
Advertisement
Table of Contents
