Related Manuals for Advantech UNO-137 V2
Summary of Contents for Advantech UNO-137 V2
- Page 1 User Manual UNO-137 V2 電腦 ® Intel Atom x6413E and x6425RE processor Automation Computer, with 2 x LAN, 2 x COM, 4 x USB, 2 x DP, 8 xDIO, 1 x mPCIe, and 2 x M.2...
- Page 2 No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. The information provided in this manual is intended to be accurate and reliable.
- Page 3 UNO137I23B2402-T UNO137I23B2409-T UNO137I23B2305-T UNO137I23B2403-T UNO137I23B2410-T UNO137I23B2306-T UNO137I23B2501-T UNO137I23B2509-T UNO137I23B2606-T UNO137I23B2502-T UNO137I23B2510-T UNO137I23B2607-T UNO137I23B2503-T UNO137I23B2601-T UNO137I23B2608-T UNO137I23B2504-T UNO137I23B2602-T UNO137I23B2609-T UNO137I23B2505-T UNO137I23B2603-T UNO137I23B2610-T UNO137I23B2506-T UNO137I23B2604-T UNO137I23B2701-T UNO137I23B2507-T UNO137I23B2605-T UNO137I23B2702-T UNO137I23B2508-T UNO137I23B2703-T UNO137I23B2704-T UNO137I23B2705-T UNO137I23B2706-T UNO137I23B2707-T UNO137I23B2708-T UNO137I23B2709-T UNO137I23B2710-T UNO-137 V2 User Manual...
- Page 4 Product Warranty (2 years) Advantech warrants the original purchaser that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products that have been repaired or altered by persons other than repair personnel authorized by Advantech, or products that have been subject to misuse, abuse, accident, or improper installation.
- Page 5 This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This type of cable is available from Advantech. Please contact your local supplier for ordering information.
- Page 6 Before system installation, check that the items listed below are included and in good condition. If any item does not accord with the list, contact your dealer immediately. UNO-137 V2 (with din-rail mount) 1 x 2x5 Plug-in block for COM port ...
- Page 7 This product is intended to be supplied by an UL certified power supply or dc source with SELV output, rated 10 Vdc, 7.7A minimum and Tma 40 degree. If you need further assistance, please contact Advantech for further information. Ensure that the voltage of the power source is correct before connecting the equipment to a power outlet.
- Page 8 If the equipment is used in a manner not specified by the Advantech, the protec- tion provided by the equipment may be impaired. The equipment contains no user-serviceable parts. Do not open, Return to man- ufacturer for servicing. Do not block air ventilation holes.
- Page 9 電源線或者插頭損壞； 設備內部有液體流入； 設備曾暴露在過於潮濕的環境中使用； 設備無法正常工作，或您無法通過用戶手冊來使其正常工作； 設備跌落或者損壞； 設備有明顯的外觀破損。 請不要把設備放置在超出我們建議的溫度範圍的環境，即不要低於 -40°C （- 4°F）或高於 70°C （158°F)） ，否則可能會損壞設備。 注意：若電池更換不正確，將有爆炸危險。因此，只可以使用製造商推薦的同一 種或者同等型號的電池進行替換。請按照製造商的指示處理舊電池 根據 IEC 704‐1:1982 規定，操作員所在位置音量不可高於 70 分貝。 限制區域：請勿將設備安裝於限制區域使用。 免責聲明：請安全訓示符合 IEC 704‐1 要求。研華公司對其內容之準確性不承 擔任何法律責任。 消费者若使用电源适配器供电，则应购买配套使用获得 CCC 认证并满足标准要 求的电源适配器。 UNO-137 V2 User Manual...
- Page 10 限用物質含有情況標示聲明書 Declaration of the Presence Condition of the Restricted Substances Marking 型號 （型式） ：UNO-137 V2 ( 系列型號請參見手冊載明型號） 設備名稱：電腦 Equipment name Type designation (Type) 限用物質及其化學符號 Restricted substances and its chemical symbols 單元 六價鉻 多溴聯苯 多溴二苯醚 鉛 汞 鎘 Unit Hexavalent Polybrominat...
-
Page 11: Table Of Contents
Chapter Hardware Functionality.....17 Introduction ..................... 18 Figure 3.1 Diagram of Connector Locations on UNO-137 V2 (Top Side) ................. 18 Figure 3.2 Diagram of Key Components Location on UNO-137 V2 (Bottom Side)............18 Table 3.1: Key Components, Connectors on Board ....19 External I/O Connectors................ - Page 12 Figure A.6 Power & performance..........45 Figure A.7 CPU - Power management control-1 ....... 46 Figure A.8 CPU - Power management control-2 ....... 46 Figure A.9 GT – Power management control ......48 Figure A.10GT disable Turbo GT frequency-1 ......49 UNO-137 V2 User Manual...
- Page 13 Figure A.29PCH-IO configuration – 2 ......... 61 Figure A.30PCH-IO configuration – 3 ......... 61 Figure A.31PCH-IO configuration – 4 ......... 62 Figure A.32Security ..............63 Figure A.33Boot ................64 Figure A.34Save & exit ............... 65 xiii UNO-137 V2 User Manual...
- Page 14 UNO-137 V2 User Manual...
-
Page 15: Chapter 1 Overview
Chapter Overview This chapter overviews specifica- tions for UNO-137 V2. Introduction Safety precautions Accessories Hardware Specifications Dimensions... -
Page 16: Introduction
The new integrated DIN-rail mounting kit is designed to be more ruggedized and user-friendly, making it a perfect fit for control cabinets. This new UNO-137 V2 model features a ruggedized design with an industrial-grade ® Intel Atom x6413E 1.5 GHz and x6425RE 1.9 GHz processor and built-in 8 GB... -
Page 17: Hardware Specifications
USB (Type A): 2 x USB 3.2 Gen 2, x USB 3.2 Gen 1 and 1 x USB 2.0 8-ch digital input, 8-ch digital output (isolation protection: 2500V Isolated DIO Displays 2 x DP 1.2, up to 4096 x 2160 @ 60 Hz Power Connector 1 x 2 Pin (terminal block) UNO-137 V2 User Manual... -
Page 18: Environment
CE, FCC, UL 61010-1, CCC, BSMI 1.3.6 Extension Kit (Optional) UNO-137 V2 features a modularized design. Advantech offers an optional 2nd stack extension kit for users to expand the functionality using an Advantech iDoor module. Table 1.6: Extension Kit (Optional) -
Page 19: Dimensions
Dimensions 35 mm x 105 mm x 150 mm (1.4 in x 4.1 in x 5.9 in) Figure 1.1 UNO-137 V2 Dimensions Figure 1.2 UNO-137 V2 Dimensions (with Optional Extension Kit) UNO-137 V2 User Manual... - Page 20 UNO-137 V2 User Manual...
-
Page 21: Chapter 2 Initial Setup
Chapter Initial Setup This chapter explains how to Initial- ize the UNO-137 V2. Chassis Grounding Connecting Power Storage Installation (Optional) Din-Rail Installation Wireless Module Installation (Optional) Expansion Module Installation (Optional) Remote Power/On & Reset Set- ting ... -
Page 22: Chassis Grounding
Chassis Grounding The UNO-137 V2 provides good EMI protection and a stable grounding base. There is an easy-to-connect chassis grounding point. Figure 2.1 Connection Diagram Use the grounding cable (16 AWG) from the accessory bag to connect the chassis ground with the earth ground. -
Page 23: Connecting Power
This product is intended to be supplied by an approved power adapter or DC power source. This adapter is rated at 10 Vdc - 36 Vdc, 7.7 -1.31 A and has a Tmax of 70°C (158°F). If you need further assistance or information, please contact Advantech. Note! It is recommended to choose a 120 W adapter when selected iDoor expansion module(e.g. -
Page 24: Installation (Optional)
M.2 Installation (Optional) The UNO-137 V2 supports the installation of M.2 E-Key 2230 and M.2 B-Key 2242. Please refer to The UNO-137 V2 Startup Manual for installation steps. 2.3.1 Antenna Installation Install the SMA connector of the antenna cable to the antenna hole. -
Page 25: Second Stack Idoor Installation (Optional)
5 x M3x4L screws for extension kit installation. Follow the steps below for extension kit Installation: Remove 2 screws from the back cover of the UNO-137 V2. Detach the iDoor dummy cover from the iDoor extension kit. UNO-137 V2 User Manual... - Page 26 Extension Kit Installation: (1) Connect the mPCIe connector of the iDoor module onto the board of the UNO-137 V2, and fix it with the M2x4L screw from the accessory bag of the UNO-137 V2. (2) Attach the iDoor extension kit onto the UNO-137 V2 with 5 x M3x4L screws from its accessory bag.
-
Page 27: Base Unit: Mpcie+ Msata (Optional)
Return the back cover of the UNO-137 with the provided screws from Step 1. 2.3.3 Base Unit: mPCIe+ mSATA (Optional) Remove 2 screws from the back cover of the UNO-137 V2. Remove the provided screws from the board. Insert the mSATA card. Secure it with the provided screws Insert grease between the back cover and aluminum column and lock back the screws. - Page 28 UNO-137 V2 User Manual...
-
Page 29: 2Nd Stack: Mpcie+ Msata (Optional)
Attach the transfer plate with 4 screws to the 2nd stack. Paste thermal pad on the aluminum column then lock the second expansion chassis with 5 screws for the first chassis. Fix the back cover with the provided screws. UNO-137 V2 User Manual... -
Page 30: Remote Power & Reset Settings
Remote Power & Reset Settings The UNO-137 V2 supports remote power and reset functions through the DI connec- tor with the switch setting (SW8) on the motherboard. The default setting is for DI6/ DI7 functionality. If you want to configure the UNO-137 for remote control functions, configure SW8- Bit 2 to “on”, then the DI6 can be used for remote power settings, and... -
Page 31: Chapter 3 Hardware Functionality
Chapter Hardware Functionality This chapter details setup instruc- tions for UNO-137 V2’s hardware functions. It includes connecting peripherals and indicators. Introduction External I/O Connector Internal I/O Connector LED Indicators Reset Buttons Antenna Hole... -
Page 32: Introduction
The following diagram demonstrates the location of the UNO-137 V2 motherboard’s key components and internal/external connectors. Figure 3.1 Diagram of Connector Locations on UNO-137 V2 (Top Side) Figure 3.2 Diagram of Key Components Location on UNO-137 V2 (Bottom Side) UNO-137 V2 User Manual... -
Page 33: External I/O Connectors
M.2 M-Key for 2242 Connector M2_E1 M.2 E-Key for 2230 Connector MINIPCIE_MSATA1 Mini PCIe Connector Internal DCOUT1 Expansion iDoor Power Connector BAT1 RTC Battery Connector SIM1 SIM Card Connector External I/O Connectors Figure 3.3 Front Panel of UNO-137 V2 UNO-137 V2 User Manual... -
Page 34: Power Connector
3.2.3 USB Connector The UNO-137 V2 features 4 x USB ports that comply with 3 x Rev 3.2, 1 x Rev 2.0 specifications. The USB connectors support plug-and-play and hot-swapping func- tionality for external devices. Additionally, this can be enabled/disabled in the BIOS menu. -
Page 35: Com Connector
3.2.5 COM Connector The UNO-137 V2 has 2 x COM RS232/422/485 ports of terminal block types. They offer transmission speeds of 50 kbps ~115.2 kbps. The default mode for both COM ports (COM 1 & COM 2)is RS-232 mode. Settings can be adjusted via an on-board switch (SW1). -
Page 36: Digital Input And Output
~ 30 V Input Voltage (dry contact), configure SW6 to setting 1 – Logic 0: Shorted to GND – Logic 1: Open Isolation Protection: 2,500 V Over-voltage Protection: 30 V Opto-Isolator Response: 50 μs UNO-137 V2 User Manual... - Page 37 Each of the 8 isolated digital input channels accept voltages from 0 V ~ 30 V. The fol- lowing figure shows how to connect an external input source to the isolated inputs of the UNO- 137 V2. Figure 3.5 Isolated DI Wet Connection Diagram Figure 3.6 Isolated DI Dry Connection Diagram UNO-137 V2 User Manual...
-
Page 38: Internal I/O Connectors And Switches
(500 mA max./ch), the board's current will sink from the external voltage source. The following figure shows how to connect an external output load to the isolated outputs on the UNO-137 V2. Figure 3.7 Isolated DO Connection Diagram... -
Page 39: Connector
DI selection for dry/wet contact Note! *This power is from DC power inputs. *JCMOS 1: Configure the UNO-137 V2 to match the needs of your application by setting switches, The following details the switch setting definitions: 3.3.1 M.2 Connector There is one M.2 M-Key connector for M.2 cards, labeled “M2_M1” on the board. -
Page 40: Minipcie_Msata1 Connector
BTR (RTC Battery): Red indicates a low RTC battery. Check the RTC battery. RUN (Programmable): Users can configure the LED indicator’s behavior through GPO signal controls. Green indicates under programming. 3.4.2 Reset Buttons Press the “reset” button to initiate a hardware reset. UNO-137 V2 User Manual... -
Page 41: Antenna Hole
LTE or wireless functions. Note! Please be aware of the maximum OD value of the antenna hole when selecting the antenna. Figure 3.10 Diagram of Maximum OD Value for Antenna Hole UNO-137 V2 User Manual... - Page 42 UNO-137 V2 User Manual...
-
Page 43: Appendix A System Settings/Pin Assignments
Appendix System Settings/Pin Assignments... -
Page 44: Power Connector (Dcin1)
In MDI and in MDI-X configuration, MDI[2]+/- corresponds MDI2- to BI_DC+/- and MDI[3]+/ - corresponds to BI_DD+/-. MDI3+ 100BASE-TX: Unused. MDI3- 10BASE-T: Unused. Table A.3: LED Left LED Right LED 100/10 Link 1000 Link 2500 Link Active Orange Green Green UNO-137 V2 User Manual... -
Page 45: Usb Connector
Table A.5: USB 3.0 Connector Pin Assignments Signal Name Description VBUS Power USB 2.0 differential pair Ground for power return StdA_SSRX- SuperSpeed receiver differential pair StdA_SSRX+ GND_DRIAN Ground for signal return StdA_SSTX- SuperSpeed transmitter differential pair StdA_SSTX+ UNO-137 V2 User Manual... -
Page 46: Display Connector (Dp1, Dp2)
Display Connector (DP1, DP2) Table A.6: Display Port Adapter cable Pin Assignments Signal Name DP0_z_D0+ DP0_z_D0- DP0_z_D1+ DP0_z_D1- DP0_z_D2+ DP0_z_D2- DP0_z_D3+ DP0_z_D3- DP0_AUX_EN# DP0_CONFIG DP0_AUX_P DP0_AUX_N DP0_z_HPD +V3.3 UNO-137 V2 User Manual... -
Page 47: M.2 Connector (M2_M1)
M.2 Connector (M2_M1) Table A.7: M.2 M-Key Connector Pin Assignments Signal Name Signal Name +V3.3_SB_NVME1 +V3.3_SB_NVME1 +V3.3_SB_NVME1 +V3.3_SB_NVME1 +V3.3_SB_NVME1 +V3.3_SB_NVME1 PCIE_CPU_M2_M1_RX_N2 PCIE_CPU_M2_M1_RX_P2 PCIE_CPU_M2_M1_TX_N2 PCIE_CPU_M2_M1_TX_P2 UNO-137 V2 User Manual... -
Page 48: M.2 Connector (M2_E1)
Table A.7: M.2 M-Key Connector Pin Assignments PCIE_CPU_M2_M1_RX_N1 PCIE_CPU_M2_M1_RX_P1 PCIE_CPU_M2_M1_TX_N1 PCIE_CPU_M2_M1_TX_P1 PLTRST_MKEY# PCIE_REQ# CLK100M_PCH_M2_M1_K_N PCIE_WAKE# CLK100M_PCH_M2_M1_K_P SUSCLK PEDET +V3.3_SB_NVME1 +V3.3_SB_NVME1 +V3.3_SB_NVME1 M.2 Connector (M2_E1) Table A.8: M.2 E-Key Connector Pin Assignments Signal Name Signal Name USB2_PCH_M2_E1_A_D_P +V3.3_SB_M2_E1 USB2_PCH_M2_E1_A_D_N +V3.3_SB_M2_E1 UNO-137 V2 User Manual... - Page 49 Table A.8: M.2 E-Key Connector Pin Assignments PCIE_PCH_M2_E1_TX_P1 PCIE_PCH_M2_E1_TX_N1 PCIE_CPU_M2_E1_RX_P1 PCIE_CPU_M2_E1_RX_N1 CLK100M_PCH_M2_E1_K_P1 CLK100M_PCH_M2_E1_K_N1 PLTRST_MKEY# PCIE_REQ# CLKREQ4# +V3.3_SB_M2_E1 PCIE_WAKE# WIFI_OFF# PCIE_PCH_M2_E1_TX_P2 PCIE_PCH_M2_E1_TX_N2 PCIE_CPU_M2_E1_RX_P2 PLRST PCIE_CPU_M2_E1_RX_N2 PCIE_WAKE# CLK100M_PCH_M2_E1_K_P2 +V3.3_SB_M2_E1 CLK100M_PCH_M2_E1_K_N2 +V3.3_SB_M2_E1 UNO-137 V2 User Manual...
-
Page 50: Mpcie Connector (Minipcie_Msata1)
Table A.9: mPCIe Connector Pin Assignments Signal Name Signal Name PCIE_WAKE#_3.3 +V3.3_SB_MINI +V1.5_MINI1 +V3.3 +VUIM_VPP UIM_RESET CLK100M_PCH_MINI1_K_N UIM_CLK CLK100M_PCH_MINI1_K_P UIM_DATA +VUIM_PWR WIFI_DISABLE# MINI_PLTRST# SWITCH_MINIPCIE1_RX_N +V3.3_SB_MINI SWITCH_MINIPCIE1_RX_P +V1.5_MINI1 SWITCH_MINIPCIE1_TX_N SWITCH_MINIPCIE1_TX_P USB2_PCH_MINI1_D_N USB2_PCH_MINI1_D_P +V3.3_SB_MINI +V3.3_SB_MINI MPCIE_PWRSEL +V1.5_MINI1 MINIPCIE1_DET# +V3.3_SB_MINI UNO-137 V2 User Manual... -
Page 51: Com Port Rs232/422/485 Settings
This switch is used to select RS232/422/485 mode settings Default RS232 mode Bit 1 ON RS232 Mode Bit 2,3,4,5,6,7,8,9,10 OFF Bit 2,4,5 ON COM1 RS485 Mode Bit 1,3,6,7,8,9,10 OFF Bit 1,2,4,5 ON RS422 Mode Bit 3,6,7,8,9,10 OFF UNO-137 V2 User Manual... -
Page 52: Com Port Rs422/485 Termination Resistor Setting
Termination resistor setting This switch is used to select the termination resistor (120 ohm) for long Description distance transmissions or device matching Default Bit 3 off & Bit 8 off COM1 Bit 3 on COM2 Bit 8 on UNO-137 V2 User Manual... -
Page 53: At/Atx Setting (Pson1)
Table A.13: Expansion Board to Board Connector Pin Assignments Signal Name Signal Name eDP_HPD# eDP_TX0+ eDP_TX0- eDP_TX1+ eDP_TX1- eDP_AUX+ eDP_AUX- PLTRST_B2B# PMU_SLP_S3# eDP_VDDEN_1V8 eDP_BKLTEN_1V8 eDP_BKLCTL_1V8 EC_LVDS_BKLT_EN EC_LVDS_BKLT_CTL ouch_EN_1V8 PCIE_WAKE#_3.3 CLK_PCIE_mPCIe0+ CLK_PCIE_mPCIe0- PCIE_TX2+ PCIE_TX2- PCIE_RX2+ PCIE_RX2- USB2_P2+ USB2_P2- PCIE_MINI1_CLKREQ# UNO-137 V2 User Manual... -
Page 54: Tpm 2.0 Bios Setting
A.10 TPM 2.0 BIOS Setting The UNO-137 V2 system supports TPM 2.0 functionality. This can be enabled or dis- abled in the BIOS menu by following the instructions provided below: Power on the UNO-137 system and press “delete” to enter the BIOS configura- tion menu. -
Page 55: Bios Operation
The setup utility uses a number of menus for making changes and turning the specific features on or off. This chapter describes the basic navigation of the UNO-137 V2 setup screens. Figure A.1 Main setup screen AMI’s BIOS ROM has a built-in setup program that allows users to modify the basic... - Page 56 Highlight System Time or System Date using the keys. Enter new values through the keyboard, press the key or the keys to move between fields. The date must be entered in MM/DD/YY format. The time must be entered in HH:MM:SS format. UNO-137 V2 User Manual...
- Page 57 A.11.1.3 Advanced BIOS Features Select Advanced Tab from the UNO-137 V2 setup screen to enter the advanced BIOS setup screen. You can select any of the items in the left frame of the screen, such as CPU configuration, by going to the sub menu for that item. You can display an advanced BIOS setup option by highlighting it using the keys.
- Page 58 A.11.1.4 CPU Configuration Figure A.4 CPU configuration Figure A.5 CPU configuration-1 CPU Flex Ratio Overide Enable/disable CPU flex ratio programming. UNO-137 V2 User Manual...
- Page 59 SMM Use Block Indication Enable/disable usage of SMM_BLOCKED MSR for MP Sync in SMI. – SMM Use SMM en-US Indication Enable/Disable usage of SMM_ENABLE MSR for MP Sync in SMI. A.11.1.5 Power & Performance Figure A.6 Power & performance UNO-137 V2 User Manual...
- Page 60 Figure A.7 CPU - Power management control-1 Figure A.8 CPU - Power management control-2 UNO-137 V2 User Manual...
- Page 61 Timed MWAIT Enable/Disable timed MWAIT support. Custom P-state Table Add custom P-state table EC Turbo Control Mode Enable/Disable EC turbo control mode. Energy Performance Gain Enable/Disable energy performance gain. CPU Lock Configuration UNO-137 V2 User Manual...
- Page 62 GT – Power Management Control Figure A.9 GT – Power management control UNO-137 V2 User Manual...
- Page 63 Maximum GT frequency limited by the user. Choose between 200 MHz (RPN) AND 750 MHz (RP0). Value beyond this range will be clipped to min/max sup- ported by the SKU. Disable Turbo GT Frequency Enabled: Disables Turbo GT frequency. Disabled: GT frequency is not limited. UNO-137 V2 User Manual...
- Page 64 A.11.1.6 PCH-FW Configuration: Configure Management Engine Technology Parameters Figure A.11 PCH-FW configuration Figure A.12 PCH-FW configuration - 1 ME State When disabled, ME will be put into ME temporarily disabled mode. UNO-137 V2 User Manual...
- Page 65 Firmware Update Configuration Configure management engine technology parameters. A.11.1.7 Trusted Computing Figure A.13 Trusted computing Figure A.14 Trusted computing-1 UNO-137 V2 User Manual...
- Page 66 TCG EFI protocol and INT1A interface will not be available. Disable Block Sid Override to allow SID authentication in the TCG storage device. A.11.1.8 ACPI Settings: System ACPI Parameters Figure A.15 ACPI setting UNO-137 V2 User Manual...
- Page 67 Enable or disable system’s ability to hibernate (OS/S4 sleep state). This option may not be effective with some operating systems. ACPI Sleep State Select the highest ACPI sleep state the system will enter when the SUSPEND button is pressed. UNO-137 V2 User Manual...
- Page 68 A.11.1.9 NCT61260 Super IO Configuration: System Super IO Chip Parameters Figure A.17 NCT61260 super IO configuration Figure A.18 NCT61260 super IO configuration-1 Serial Port 1 Configuration Set parameters of serial port 1 (COM). UNO-137 V2 User Manual...
- Page 69 Serial Port 2 Configuration Set Parameters of Serial Port 2 (COMB). A.11.1.10NCT6126D HW Monitor: Monitor Hardware Status Figure A.19 H/W monitor configuration Figure A.20 H/W monitor configuration-1 PC Health Status UNO-137 V2 User Manual...
- Page 70 Enable or disable system wake on alarm event. Select Fixed Time, and the sys- tem will wake on the hr::min::sec specified. Select dynamic time. The system will wake at the current time + Increase minute(s). UNO-137 V2 User Manual...
- Page 71 Mass Storage Devices: USB Mass storage device emulation type. “AUTO” enumerates devices according to their media format. Optical drives are emulated as “CDROM”, drives with no media will be emulated according to a drive type. UNO-137 V2 User Manual...
- Page 72 A.11.1.13Network Stack Settings Figure A.24 Network stack configuration Network Stack Enable/Disable UEFI network stack. A.11.1.14Chipset Figure A.25 Chipset UNO-137 V2 User Manual...
- Page 73 Keep IGFX enabled based on the setup options. VT-d Above 4 GB MMIO BIOS assignment Enable/Disable above 4 GB memory-mapped IO BIOS assignment. This is enabled automatically when aperture size is set to 2048 MB. UNO-137 V2 User Manual...
- Page 74 A.11.1.15PCH-IO Configuration Figure A.27 PCH-IO configuration Figure A.28 PCH-IO configuration – 1 UNO-137 V2 User Manual...
- Page 75 Figure A.29 PCH-IO configuration – 2 Figure A.30 PCH-IO configuration – 3 UNO-137 V2 User Manual...
- Page 76 Enable/Disable SATA Device. SATA Mode Selection – Determines how SATA controller(s) operate. – Aggressive LPM Support Enable PCH to aggressively enter link power state. – SATA Controller Speed Indicates the maximum speed the SATA controller can support. UNO-137 V2 User Manual...
- Page 77 Restore Factory Keys – Forces system into user mode. Installs factory default Secures boot key data- bases. – Key Management Enables expert users to modify secure boot policy variables without full authentication. SQF-C4MV2-128GDEDE TCG Storage Security Configuration. UNO-137 V2 User Manual...
- Page 78 Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinites waiting. – Bootup NumLock State Select the keyboard <NumLock> state. Quiet Boot – Enables or disables quiet boot option. Boot Priorities – Boot Option #1 Select the system boot order. UNO-137 V2 User Manual...
- Page 79 Restore/Load default values for all the setup options. Saves as User Defaults Save the changes done so far as User defaults. Restore User Defaults Restore the user defaults t all the setup options. UEFI: USB, Partition 1 (USB) UNO-137 V2 User Manual...
- Page 80 No part of this publication may be reproduced in any form or by any means, such as electronically, by photocopying, recording, or otherwise, without prior written permission from the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2023...