Related Manuals for Advantech UNO-137
Summary of Contents for Advantech UNO-137
- Page 1 User Manual UNO-137 電腦 Intel Atom® E3940 processor Automation Computer, with 2x LAN, 2x COM, 4x USB, 2x DP, 8x DIO, 1x mPCIe, and 1x M.2...
- Page 2 No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
- Page 3 Because of Advantech’s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defec- tive, it will be repaired or replaced at no charge during the warranty period. For out- of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight.
- Page 4 這是甲類測試產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下， 使用者會被要求採取某些適當的對策。 Technical Support and Assistance Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call: –...
- Page 5 This equipment is not suitable for use in locations where children are likely to be present. If the equipment is used in a manner not specified by the Advantech, the protec- tion provided by the equipment may be impaired. The equipment contains no user-serviceable parts. Do not open, Return to man- ufacturer for servicing.
- Page 6 Pour une utilisation dans des environnements non polluant et à l'intérieur. C'est appareil ne doit pas être utilisé dans des endroits où se trouvent des enfants. Si l'équipement est utilisé d'une manière non spécifiée par le fabricant, la pro- tection fournie par l'équipement peut être altéré UNO-137 User Manual...
- Page 7 請勿讓任何液體流入通風口，以免引起火灾或短路。 請勿自行打開設備。為了確保您的安全，請透過經認證的工程師來打開設備。 如遇下列情况，請由專業人員維修： 電源線或插頭損壞； 設備內部有液體流入； 設備曾暴露在過度潮濕環境中使用； 設備無法正常工作，或您無法透過用戶手冊來正常工作； 設備摔落或損壞； 設備有明顯外觀損； 請勿將設備放置在超出建議溫度範圍的環境，即不要低於 -40 ℃ （-40 ℉）或 高於 70 ℃ （158 ℉），否則可能會造成設備損壞。 注意：若電池更換不正確，將有爆炸危險。因此，只可以使用製造商推薦的同一 種或者同等型號的電池進行替換。請按照製造商的指示處理舊電池。 根據 IEC 704‐1:1982 規定，操作員所在位置音量不可高於 70 分貝。 限制區域：請勿將設備安裝於限制區域使用。 免責聲明：請安全訓示符合 IEC 704‐1 要求。研華公司對其內容之準確性不承 擔任何法律責任。 消费者若使用电源适配器供电，则应购买配套使用获得 CCC 认证并满足标准要 求的电源适配器。 UNO-137 User Manual...
- Page 8 UNO-137 User Manual viii...
-
Page 9: Table Of Contents
Certifications ................. 5 1.4.6 Extension Kit (Optional) ..............5 Dimensions ....................6 Figure 1.1 UNO-137 Dimensions..........6 Figure 1.2 UNO-137 Dimensions (With Optional Extension kit) .. 6 Chapter Hardware Functionality.......7 Introduction ....................8 Figure 2.1 Diagram of Connector Locations on UNO-137 (Top Side) ................ - Page 10 AT/ATX Setting (SW8) ................43 A.10 Board to Board Connector (Reserved for Expansion) (CN13) ....44 Table A.10:Expansion Board to Board Connector Pin Assignments A.11 TPM 2.0 BIOS Setting................45 A.12 CPU Turbo Mode BIOS Setting .............. 46 UNO-137 User Manual...
-
Page 11: Chapter 1 Overview
Chapter Overview This chapter overviews specifica- tions for UNO-137. Introduction Safety Precautions Accessories Hardware Specifications Dimensions... -
Page 12: Introduction
The new integrated Din-rail mounting kit is designed to be more ruggedized and user-friendly, making it a perfect fit for control cabinets. This new UNO-137 model features a ruggedized design with an industrial-grade Intel Atom® E3940 1.6GHz processor and built-in 8GB DDR3L RAM. It supports a wide temperature range (-40 ~ 70 °C/-40 ~ 158 °F) and sufficient I/O - including 2 x LAN, 2... -
Page 13: Packing List
Packing List Please refer to below packing list: UNO-137 (with din-rail mount) 1 x 2x5 Plug-in block for COM port 1 x 2x1 Plug-in block for power wiring 1 x 2x10 Plug-in block for digital I/O wiring ... -
Page 14: System Hardware
Operating, IEC 60068-2-64, 4Grms, random, 5 ~500Hz, 1hr/ axis (SSD) Vibration Protection Operating, IEC 60068-2-64, 0.3 Grms, random,5 ~ 500Hz, 1hr/ axis (HDD) Note! It is recommended to use 2.5" SSD under the temperature of 70 °C/158 °F UNO-137 User Manual... -
Page 15: Certifications
CE, FCC, UL 61010-2-201, CCC, BSMI 1.4.6 Extension Kit (Optional) UNO-137 features a modularized design. Advantech offers an optional 2nd stack extension kit for users to expand the functionality using an Advantech iDoor module. Part number UNO-137-ID1EA Description 2nd stack extension kit to support 1 x iDoor on UNO-137-E13BA... -
Page 16: Dimensions
Dimensions 35 x 105 x 150 mm (1.4 x 4.1 x 5.9 in) Figure 1.1 UNO-137 Dimensions Figure 1.2 UNO-137 Dimensions (With Optional Extension kit) UNO-137 User Manual... -
Page 17: Chapter 2 Hardware Functionality
Chapter Hardware Functionality This chapter details setup instruc- tions for UNO-137’s hardware functions. It includes connecting peripherals and indicators. Introduction External I/O Connector Internal I/O Connector LED Indicators Reset Buttons Antenna Hole... -
Page 18: Introduction
Introduction The following diagram demonstrates the location of UNO-137’s motherboard’s key components and internal/external connectors. Figure 2.1 Diagram of Connector Locations on UNO-137 (Top Side) Figure 2.2 Diagram of Key Components Location on UNO-137 (Bottom Side) UNO-137 User Manual... - Page 19 USB 3.0 Connector 8DI/ 8DO Terminal Connector COM Port Terminal Connector (RS232/422/485) SATA Power Connector SATA1 SATA Signal Connector MINI1 MiniPCIe Connector Internal CN13 Reserve for connector expansion CN15 M.2 B key for 2242/3042/3052 Connector CN12 Memory slot UNO-137 User Manual...
-
Page 20: External I/O Connector
External I/O Connector Figure 2.3 Front Panel of UNO-137 Figure 2.4 Top View of UNO-137 UNO-137 User Manual... -
Page 21: Power Connector
2.2.3 USB Connector UNO-137 features 4x USB ports that comply with USB EHCI, 3 for Rev. 3.0, 1 for Rev. 2.0 specifications. The USB connectors support plug-and-play and hot-swap- ping functionality for external devices. Additionally, this can be enabled/disabled in the BIOS menu. -
Page 22: Com Connector
2.2.5 COM Connector UNO-137 has 2 COM RS232/422/485 ports of terminal block type. They offer trans- mission speeds of 50 ~115.2 kbps. The default mode for both COM ports (COM1&COM2 )is RS-232 Mode. Settings can be adjusted via an on-board switch (SW1). -
Page 23: Digital Input And Output
Logic 1: 0~3 V Input Voltage (Dry Contact), Configure SW6 to Setting 1 – Logic 0: Shorted to GND – Logic 1: Open Isolation Protection 2,500 V Over-voltage Protection 30 V Opto-Isolator Response 50 μs UNO-137 User Manual... - Page 24 (500 mA max./ ch), the board's current will sink from the external voltage source. The following figure shows how to connect an external output load to the isolated outputs on UNO-137. Figure 2.7 Isolated DO Connection Diagram...
-
Page 25: Internal I/O Connectors And Switches
Internal I/O Connectors and Switches The following figure demonstrates the locations of internal connectors and switches on the UNO-137’s motherboard. Figure 2.8 Locations Internal I/O Connectors/Switches for UNO-137 Table 2.3: Internal Connectors and Jumper Switches Label Function MINI1 MiniPCIe Connector CN15 M.2 B key for 2242/3042/3052 Connector... -
Page 26: Sata Connector/Sata Power Connector
Configure the UNO-137 to match the needs of your application by setting switches, The following details the switch setting definitions: 2.3.1 SATA Connector/SATA Power Connector There’re two required onboard connectors needed to connect with 2.5" SATA SSD/ HDD. the location labeled “SATA1” is for SATA connector, and the location labeled “CN9”... -
Page 27: Others
BTR(RTC Battery): Red indicates a low RTC battery. Check the RTC battery. RUN(Programmable): Users can configure the LED indicator’s behavior through GPO signal controls. Green indicates under programming. 2.4.2 Reset Buttons Press the “Reset” button to initiate a hardware reset. UNO-137 User Manual... -
Page 28: Antenna Hole
LTE or wireless functions. Note! Please be aware of the Maximum OD value of the Antenna Hole when selecting antenna Figure 2.10 Diagram of Maximum OD Value for Antenna Hole UNO-137 User Manual... -
Page 29: Chapter 3 Initial Setup
Chapter Initial Setup This chapter explains how to Ini- tialize the UNO-137 Chassis Grounding Connecting Power Storage Installation (Optional) Din-Rail Installation Wireless Module Installation (Optional) Expansion Module Installation (Optional) Remote Power/On & Reset Set- ting ... -
Page 30: Chassis Grounding
Chassis Grounding The UNO-137 provides good EMI protection and a stable grounding base. There is an easy-to-connect chassis grounding point. Figure 3.1 Chassis Grounding Connection Diagram Use the Grounding cable (16 AWG) from the accessory bag to connect the chassis ground with the Earth ground. -
Page 31: Storage Installation (Optional)
Storage Installation (optional) UNO-137 supports the installation of one 2.5” HDD/ SDD and one M.2 2242 SSD.The installation is demonstrated in the following steps. 3.3.1 Installing a 2.5” HDD/SSD Remove 2 screws from UNO’s back cover. UNO-137 User Manual... - Page 32 Remove the 4x plugs on the back cover, and secure the HDD/SSD with the 4 x M3x5L screws. UNO-137 User Manual...
- Page 33 (1) Plug in the SATA cable on the location: “SATA1”,”CN9”. Connect SATA cable with SSD/HDD. (2) Fix the back cover with the provided screws from Step 1. *4 x M3x5L screws, 1 x SATA cable are in accessory bag. UNO-137 User Manual...
-
Page 34: Installing M.2 Ssd
3.3.2 Installing M.2 SSD Remove 2x screws from the back cover of UNO. Remove the provided screws from the board. Insert the M.2 card on the location: “CN15”. Secure it with the provided screws from Step 2. UNO-137 User Manual... -
Page 35: Din-Rail Installation
Din-Rail Installation Install UNO-137 on the rail and secure it to the rail. Pull down the “Release Latch” for disassembly using a screwdriver. UNO-137 User Manual... -
Page 36: Wireless Module Installation (Optional)
Wireless Module Installation (Optional) UNO-137 supports to install WiFi iDoor/M.2 3042/M.2 3052 module. Follow the steps below for installation: Remove 2 screws from back cover of UNO. Remove the plug of antenna pre-cut hole(s) on the top panel for antenna instal-... - Page 37 (2) Insert the M.2 card to the location: “CN15” and secure it with the provided screws from Step 3-1 Install the SMA connector of *Antenna cable to the Antenna hole Connect the MHF of Antenna cable with module Return the back cover and gently screw it into place UNO-137 User Manual...
- Page 38 Assemble the *Antenna on the SMA connector of the Antenna cable *Wireless Module, Antenna cable, Antennas are optional, please contact Advantech for further information. UNO-137 User Manual...
- Page 39 Note! If you need to install M.2 3052 Module, please follow the following steps Remove the on-board “bracket” Use the provided screws from Step1 to fix the M.2 3052 module UNO-137 User Manual...
-
Page 40: Extension Kit Installation (Optional)
Extension Kit Installation (Optional) You can additionally install 2nd stack iDoor extension kit (PN:UNO-137-ID1EA) on UNO-137 to expand its functionality: The accessory list for iDoor extension kit (PN:UNO-137-ID1EA) 5 x M3x4L screws for extension kit installation 4 x M3x4L screws for HDD installation Follow the steps below for extension kit Installation: Remove 2 screws from back cover of UNO-137. - Page 41 (1) Connect the mPCIe connector of iDoor module onto the board of UNO-137, and fix it with the M2x4L screw from the accessory bag of UNO-137 (2) Fix iDoor extension kit onto UNO-137 with 5 x M3x4L screws from its acces- sory bag...
- Page 42 Fix the HDD bracket back onto the extension kit with the provided screws from step 1. Extension Kit installation: (1) Plug in SATA cable onto the board of UNO-137 and connect with SSD/HDD. (2) Fix extension kit onto UNO-137 with 5 x M3x4L screws from its accessory UNO-137 User Manual...
- Page 43 Return the back cover of UNO-137. UNO-137 User Manual...
-
Page 44: Remote Power & Reset Settings
(SW8) on the motherboard. The default setting is for DI6/DI7 function- ality. If you want to configure UNO-137 for remote control functions, configure SW8- Bit 2 to “on”, then DI6 can be used for remote power settings, and DI7 can be used for remote reset setting. -
Page 45: Appendix A System Settings/Pin Assignments
Appendix System Settings/Pin Assignments... -
Page 46: Power Connector (Cn1)
1000BASE-T: In MDI and in MDI-X configuration, MDI2- MDI[2]+/- corresponds to BI_DC+/- and MDI[3]+/ - MDI3+ corresponds to BI_DD+/-. 100BASE-TX: Unused. MDI3- 10BASE-T: Unused. Left LED Right LED 100 Link 1000 Link Active 10Link Orange Green Green UNO-137 User Manual... -
Page 47: Usb Connector (Cn5,Cn6)
Table A.4: USB 3.0 Connector Pin Assignments Signal Name Description VBUS Power USB 2.0 differential pair Ground for power return StdA_SSRX- SuperSpeed receiver differential pair StdA_SSRX+ GND_DRIAN Ground for signal return StdA_SSTX- SuperSpeed transmitter differential pair StdA_SSTX+ UNO-137 User Manual... -
Page 48: Display Connector (Cn2,Cn3)
Signal Name ML_Lane 0 (p) ML_Lane 0 (n) ML_Lane 1 (p) ML_Lane 1 (n) ML_Lane 2 (p) ML_Lane2 (2) ML_Lane 3 (p) ML_Lane 3 (n) CONFIG1 CONFIG2 AUX CH (p) AUX CH (n) Hot Plug Return DP_PWR UNO-137 User Manual... -
Page 49: Sata Connector/ Sata Power Connector
Table A.6: SATA Connector Pin Assignments Signal Name SATA0_C_TX+ SATA0_C_TX- SATA0_RX- SATA0_RX+ A.5.2 SATA Power Connector (CN9) Table A.7: SATA Power Connector Pin Assignments Signal Name Description +V5SATA Power Ground for power return Ground for power return Reserved UNO-137 User Manual... -
Page 50: Connector (Cn15)
Mechanical notch B Mechanical notch B Mechanical notch B Mechanical notch B Mechanical notch B Mechanical notch B WAKE_ON_WAN# M2_LTE_W2_DISABLE_N USB_Z_SSRX1- M2_SIM1_RESET USB_Z_SSRX1+ M2_SIM1_CLK M2_SIM1_DATA USB_C_SSTX1- M2_SIM1_PWR USB_C_SSTX1+ M2_SIM2_DET SATA1_RX+ SATA1_RX- SATA1_C_TX- SATA1_C_TX+ M2_SIM1_DET LTE_RST#_P67 +V3.3_M2 +V3.3_M2 +V3.3_M2 UNO-137 User Manual... -
Page 51: Mpcie Connector (Mini1)
Connector (MINI1) Table A.9: mPCIe Connector Pin Assignments Signal Name Signal Name PCIE_WAKE#_3.3 +V3.3_MINI +V1.5 +V3.3 CLK_PCIE_mPCIe1- CLK_PCIE_mPCIe1+ WIFI_DISABLE# MINI_PLTRST# PCIE_mPCIe_RX4- +V3.3_MINI PCIE_mPCIe_RX4+ +V1.5 PCIE_TX2-_Z PCIE_TX2+Z USB_Z_P0- USB_Z_P0+ +V3.3_MINI +V3.3_MINI MPCIE_PWRSEL +V1.5 +V3.3_MINI UNO-137 User Manual... -
Page 52: Com Port Rs232/422/485 Settings
Mode Bit 1,3,6,7,8,9,10 OFF RS422 Bit 1,2,4,5 ON Mode Bit 3,6,7,8,9,10 OFF RS232 Bit 6 ON Mode Bit 1,2,3,4,5,7,8,9,10 OFF RS485 Bit 7,9,10 ON COM2 Mode Bit 1,2,3,4,5,7,8 OFF RS422 Bit 6,7,9,10 ON Mode Bit 1,2,3,4,5,8 OFF UNO-137 User Manual... -
Page 53: Com Port Rs422/485 Termination Resistor Setting
AT/ATX Setting (SW8) SW8 can be used for AT/ATX setting. The default setting is AT mode. See the follow- ing table for switch configuration. SW8 Default Description Instruction AT Mode Bit 1 off (Default) ATX Mode Bit 1 on UNO-137 User Manual... -
Page 54: Board To Board Connector (Reserved For Expansion) (Cn13)
Table A.10: Expansion Board to Board Connector Pin Assignments Signal Name Signal Name eDP_HPD# eDP_TX0+ eDP_TX0- eDP_TX1+ eDP_TX1- eDP_AUX+ eDP_AUX- PLTRST_B2B# PMU_SLP_S3# eDP_VDDEN_1V8 eDP_BKLTEN_1V8 eDP_BKLCTL_1V8 EC_LVDS_BKLT_EN EC_LVDS_BKLT_CTL ouch_EN_1V8 PCIE_WAKE#_3.3 CLK_PCIE_mPCIe0+ CLK_PCIE_mPCIe0- PCIE_TX2+ PCIE_TX2- PCIE_RX2+ PCIE_RX2- USB2_P2+ USB2_P2- PCIE_MINI1_CLKREQ# UNO-137 User Manual... -
Page 55: Tpm 2.0 Bios Setting
A.11 TPM 2.0 BIOS Setting The UNO-137 systems support TPM 2.0 functionality. This can be enabled or dis- abled in the BIOS menu by following the instructions provided below: Power on the UNO-137 system and press “Delete” to enter the BIOS configura- tion menu. -
Page 56: Cpu Turbo Mode Bios Setting
A.12 CPU Turbo Mode BIOS Setting The UNO-137 systems support CPU Turbo mode. This can be enabled or disabled in the BIOS menu by following the instructions : Power on the UNO-137 system and press “Delete” to enter the BIOS configura- tion menu. - Page 57 Choose “enable/disable” to enable or disable the CPU Turbo mode (The default setting is to disable this function) UNO-137 User Manual...
- Page 58 No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permis- sion from the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd. 2020...