1. Manuals
  2. Brands
  3. Advantech Manuals
  4. Desktop
  5. UNO-1150
  6. User manual

Advantech UNO-1150 User Manual

Gx2 400mhz fanless, din-rail mounted embedded automation computer with 2 x lan, 2 x usb, 3 x com, and audio and pci-104
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
UNO-1150/UNO-1150E
GX2 400MHz Fanless, DIN-rail
Mounted Embedded Automation
Computer with 2 x LAN, 2 x USB,
3 x COM, and Audio and PCI-104

User Manual

Advertisement

Table of Contents
loading

Related Manuals for Advantech UNO-1150

Summary of Contents for Advantech UNO-1150

  • Page 1: User Manual

    UNO-1150/UNO-1150E GX2 400MHz Fanless, DIN-rail Mounted Embedded Automation Computer with 2 x LAN, 2 x USB, 3 x COM, and Audio and PCI-104 User Manual...

  • Page 2: Copyright Notice

    No part of this man- ual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reli- able.
  • Page 3 Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its prod- ucts will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or...
  • Page 4 Step 1. Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Step 2. Contact your distributor or Advantech's customer service center if you need additional assistance. Have the following info ready: - Product name and serial number - Description of your software (OS, version, software, etc.)
  • Page 5 Safety Instructions Read these safety instructions carefully. Keep this User's Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for clean- ing. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
  • Page 6 The sound pressure level at the operator's position according to IEC 704- 1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage.

  • Page 7: Table Of Contents

    Contents Chapter 1 UNO-1150 Overview ........2 Introduction ............... 2 Hardware Specifications ........... 2 Safety Precautions ............. 4 UNO-1150 Series .............. 4 Chassis Dimensions............5 Chapter 2 Hardware Functionality ......... 8 UNO-1150 Peripherals............8 COM1: RS-232 Interfaces..........10 COM2~COM3: RS-232/422/485 Interfaces ....10 2.3.1...
  • Page 8 A.10 RS-422/485 Signal Pull High/Low Settings....38 A.11 Enhanced IDE Connector (CN2) ........39 A.12 SATA Data Connector (CN100) ........40 UNO-1150 User Manual viii...
  • Page 9 UNO-1150 Overview Sections include: • Introduction • Hardware Specifications • Safety Precautions • UNO-1150 Series • Chassis Dimensions...

  • Page 10: Chapter 1 Uno-1150 Overview

    Chapter 1 UNO-1150 Overview 1.1 Introduction UNO-1150 is an DIN-rail mounted Embedded Automation Computer, which provides several serial communication ports and Ethernet interfaces. UNO- 1150 is designed with a compact size, small footprint, and help to saves space with its front accessible and DIN-rail design. With rich OS and driver support, such as Windows XP embedded, WinCE 6.0, and even embedded Linux.
  • Page 11 CompactFlash: 2 Grms @ 5 ~ 500 Hz, HDD: 0.5 Grms @ 5 ~ 500 Hz (Only for UNO-1150E) • Chassis Size (WxLxH): 85 x 155 x 140mm (3.4"x 6.1"x 5.6") (UNO-1150) 110 x 155 x 140mm (4.4"x6.1"x5.6") (UNO-1150E) • Weight: 1.6 kg (UNO-1150)

  • Page 12: Safety Precautions

    1.4 UNO-1150 Series There are three products in UNO-1150 series listed as below: • UNO-1150: UNO-1150 hardware platform • UNO-1150F: UNO-1150 with one external CompactFlash slot • UNO-1150E: UNO-1150 with PCI-104 expansion hardware platform...

  • Page 13: Chassis Dimensions

    1.5 Chassis Dimensions Figure 1.1: UNO-1150 Chassis Dimensions...
  • Page 14 Figure 1.2: UNO-1150E Chassis Dimensions UNO-1150 User Manual...
  • Page 15 Hardware Functionality Sections include: •UNO-1150 Peripherals •COM1: RS-232 Interfaces •COM2~3: RS-232/422/485 Interfaces •LAN: Ethernet Connector •Power Connector •LED Indicators •PS/2 Keyboard and Mouse Connector •Universal Serial Bus Connectors •VGA: VGA Display Connector •RESET: Reset Button •Audio •PCI-104 Voltage Selection...

  • Page 16: Chapter 2 Hardware Functionality

    2.1 UNO-1150 Peripherals The following figures show the connectors on UNO-1150 and UNO- 1150E. Information in this chapter is applied to both UNO-1150 and UNO-1150E. Therefore, in this chapter, we just mention UNO-1150 to represent the series product.The following sections give you detailed information about function of each peripheral.
  • Page 17 Figure 2.3: UNO-1150E Front View Figure 2.4: UNO-1150E Top View...

  • Page 18: Com1: Rs-232 Interfaces

    RS-422 or RS-485 network. No need to change jumpers. 2.3.3 Automatic Data Flow Control Function for RS-485 In RS-485 mode, UNO-1150 automatically senses the direction of incom- ing data and switches its transmission direction accordingly. Therefore no handshaking signal (e.g. RTS signal) is necessary. This feature lets you simply and quickly build an RS-485 network with just two wires.

  • Page 19: Rs-232/422/485 Selection

    2.3.4 RS-232/422/485 Selection COM2 and COM3 support 9-wire RS-232, RS-422 or RS-485 interfaces, and you can set corresponding jumpers to select serial ports as RS-232 or RS-422/485 interfaces shown in Table 2.2. Please note to reset the system to adapt this configuration change The system detects RS-422 or RS-485 signals automatically in RS-422/ 485 mode.

  • Page 20: Terminal Resistor Setup For Rs-422/485

    Or 120 Ohm between Tx+/Tx- (RS-422) Open (Default) 120 Ohm between Rx+/Rx- (RS-422) Open (Default) COM3 120 Ohm between Data+/ Data- (RS-485) Or 120 Ohm between Tx+/Tx- (RS-422) Open (Default) 120 Ohm between Rx+/Rx- (RS-422) Open (Default) UNO-1150 User Manual...
  • Page 21 2.3.6 RS-485 Auto Flow & RS-422 Master/Slave Mode You can set the “Auto Flow Control” mode of RS-485 or “Master/Slave” mode of RS-422 by using the SW2 DIP switch for each RS-422/485 port. In RS-485, if the switch is set to “Auto”, the driver automatically senses the direction of the data flow and switches the direction of transmission.

  • Page 22: Lan: Ethernet Connector

    2.7 PS/2 Keyboard and Mouse Connector The UNO-1150 provides a PS/2 keyboard and PS/2 mouse connector. A 6-pin mini-DIN connector is located on the rear panel of the UNO-1150. The UNO-1150 comes with an adapter to convert from the 6-pin mini- DIN connector to two 6-pin mini-DIN connectors for PS/2 keyboard and mouse connections.

  • Page 23: Universal Serial Bus Connectors

    BIOS setup. Please refer to Appendix A.7 for its pin assignments. 2.9 VGA: VGA Display Connector The UNO-1150 provides a VGA controller for a high resolution VGA interface. It supports VGA and VESA, up to 1280 x 1024 @ 256 color and 1024 x 768 @ 24bpp resolution and up to 16 MB share memory.

  • Page 24: Pci-104 Connectors (Uno-1150E)

    CN3-A. Please check your PCI-104 card support voltage to adjust the jumper on CN4. Table 2.5: PCI-104 Voltage Jumper Settings Voltage Jumper close position setting +3.3V Jumper Setting (+3.3V) example: closed 2-3 Figure 2.7: RS-422/485 Jumper Settings UNO-1150 User Manual...
  • Page 25 Initial Setup Sections include: • CompactFlash Installation • PCI-104 Card Installation (UNO-1150E) • Hard Drive Installation (UNO-1150E) • Chassis Grounding • Power Connection • BIOS Setup and System Assignments...

  • Page 26: Chapter 3 Initial Setup

    Chapter 3 Initial Setup 3.1 CompactFlash Card Installation The procedure for installing a CompactFlash card into the UNO-1150/ UNO-1150E is as follows, please follows these steps carefully. Although the outside appearance of the UNO-1150E is different from the figures shownbelow, the procedure is the same.
  • Page 27 Remove the rear cover. Plug a CompactFlash card with user’s OS and application program into a CompactFlash card slot on board. Screw back the rear cover and the six screws.

  • Page 28: Pci-104 Card Installation (Only For Uno-1150E)

    3.2 PCI-104 Card Installation (Only for UNO-1150E) The procedure for installing a PCI-104 card into the UNO-1150E is shown as following step. Remove the power. Unscrew six screws from UNO-1150E indicated below. UNO-1150 User Manual...
  • Page 29 Remove the rear cover. Find 2 metal spacer from accessory bag, and screw tight on the location indicated arrow in the below picture. (Note: There were spacers soldered on the daughter board already). Normally you will also get some hexagon spacer from your PCI-104 card packing. Use and screw those spacers on the location indicated black shown in below picture.
  • Page 30 Screw the rear cover and the six screws. Now you are done with the PCI-104 card installation. Note: You can use two PCI-104 cards at the same time while you don't use a hard drive. Using a hard drive will limit the number of PCI-104 cards allowed to one only. UNO-1150 User Manual...

  • Page 31: Hard Drive Installation (Only For Uno-1150E)

    3.3 Hard Drive installation (Only for UNO-1150E) The procedure for installing a hard drive into the UNO-1150E is shown as following step. Remove the power. Unscrew six screws from UNO-1150E indicated below. Remove the rear cover. Please refer to Section 3.1 & 3.2 for the instruction to open the cover.
  • Page 32 UNO-1150E SATA power connector doesn't support 12V power. Note There are switch setting about SATA hard drive below, please refer to the section A.9 for detail. The hard drive might not work correctly if the switch setting is incorrect UNO-1150 User Manual...

  • Page 33: Chassis Grounding

    Figure 3.1: Chassis Grounding Connection 3.5 Power Connection Connect the UNO-1150 to a 10 ~ 30 VDC power source. The power source can either be from a power adapter or an in-house power source. 3.6 BIOS Setup and System Assignments UNO-1150 uses the Advantech SOM-2354 CPU module.

  • Page 34: Din-Rail Mounting Setup

    3.7 DIN-rail Mounting Setup Please follow the below steps to mount the UNO-1150 on the DIN-Rail. Screw the provided DIN-Rail Kit on the rear side of UNO-1150 as the diagram shown below. Hang the UNO-1150 to the DIN-Rail with angle of inclination about 30 degree.

  • Page 35: Wallmounting Setup

    3.8 Wallmounting Setup Please follow the below steps to mount the UNO-1150 on the wall. Screw the provided Wall Mounting Kit on the rear side of UNO- 1150 as the diagram shown below. Mount the device on the wall by the 2 pairs hooking hole provided...
  • Page 36 UNO-1150 User Manual...

  • Page 37: Pin Assignments

    Pin Assignments This appendix shows the UNO-1150 pin assignments •Board Connectors and Jumpers •RS-232 Serial Port (COM 1) •RS-232/422/485 Serial Port (COM2~3) •Ethernet RJ-45 Connector •Power Screw Terminal •PS/2 Keyboard and Mouse Connector •USB Connector •VGA Display Connector •CompactFlash Master/Slave Jumper Setting •Enhanced IDE Connector...

  • Page 38: Appendix A Pin Assignments

    Appendix A Pin Assignments A.1 Board Connectors and Jumpers There are connectors and jumpers on the UNO-1150 board. The follow- ing sections tell you how to configure the UNO-1150 hardware setting. Figure A-1 and figure A-2 show the locations of UNO-1150 connectors and jumpers.
  • Page 39 Table A.1: Connectors & Jumpers Lithium battery for BIOS Internal CompactFlash card slot Internal IDE connector COM3 RS-232/422/485 selection Power Screw Terminal PS/2 keyboard and mouse connector CN10 COM2 RS-232/422/485 selection CN11 Ethernet port 1 / Ethernet port 2 CN12 USB connector CN13 Audio line in / Audio line out...
  • Page 40 Figure A.2: Connector & Jumper Locations (UNO-1150E) Table A.2: Connectors & Jumpers (UNO-1150E only) CN3-A PCI-104 card connector Mini PCI card connector Jumper of PCI-104 card voltage selection (+3.3V or +5V) UNO-1150 User Manual...

  • Page 41: Rs-232 Serial Port (Com1)

    A.2 RS-232 Serial Port (COM1) Table A.3: RS-232 Serial Port Pin Assignments Signal Name...

  • Page 42: Rs-232/422/485 Serial Port (Com2~Com3)

    A.3 RS-232/422/485 Serial Port (COM2~COM3) Table A.4: RS-232/422/485 Serial Ports RS-232 RS-422 RS-485 DATA- DATA+ A.4 Ethernet RJ-45 Connector (LAN1~LAN2) Table A.5: Ethernet RJ-45 Connector Pin Assigns 10/100Base-T Signal Name XMT+ XMT- RCV+ RCV- UNO-1150 User Manual...

  • Page 43: Power Screw Terminal (Cn8)

    A.5 Power Screw Terminal (CN8) Table A.6: Phoenix Power Connector Pin Assigns Signal Name VIN ( 10 ~ 36 VDC ) Field Ground A.6 PS/2 Keyboard and Mouse Connector (CN10) Table A.7: Table A.8: Keyboard & Mouse Connector Pin Assigns Signal Name KB DATA MS DATA...

  • Page 44: Usb Connector (Cn13)

    H-SYNC V-SYNC Chipset The UNO-1150 uses a AMD CS5535 chipset for its SVGA controller. It supports interlaced and non-interlaced analog monitors (color and mono- chrome VGA) in high-resolution modes while maintaining complete IBM VGA compatibility. Digital monitors (i.e. MDA, CGA and EGA) are NOT supported.

  • Page 45: Compactflash Master/Slave & Hard Drive Settings

    Note: carefully while using storage device. UNO-1150 has one internal Compact Flash card slot which supports Compact Flash type I (3mm thick) and type II (5 mm thick) cards. The CompactFlash interface uses a primary IDE channel, which can be set as the master or slave device by changing the setting of SW7.
  • Page 46 Pull high to 5V (4.7K Ohm) Open Note1: * indicate the default setting. Note2: The line would have the risk to be floating if it is set to be Open. This setting is only for special purpose. UNO-1150 User Manual...
  • Page 47 A.11 Enhanced IDE Connector (CN2) Table A.14: IDE Hard Drive Connector Pin Assigns Signal Name Signal Name IDE RESET DATA 7 (*2) DATA 8 (*2) DATA 6 (*2) DATA 9 (*2) DATA 5 (*2) DATA 10 (*2) DATA 4 (*2) DATA 11 (*2) DATA 3 (*2) DATA 12 (*2)
  • Page 48 A.12 SATA Data Connector (CN100) Table A.15: SATA DATA Connectors (CN100) UNO-1150 User Manual...

This manual is also suitable for:

Uno-1150e

Table of Contents