Related Manuals for Advantech UNO-1170E
Summary of Contents for Advantech UNO-1170E
-
Page 1: User Manual
UNO-1170/1170E Pentium M / Celeron M Fanless, DIN-rail Mounted Embedded Automation Computer with 2 x LAN, 3 x COM, 4 x USB, Audio & PC/104+ User Manual... -
Page 2: Copyright Notice
No part of this man- ual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reli- able. - Page 3 Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its prod- ucts will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or...
- Page 4 Step 1. Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Step 2. Contact your distributor or Advantech's customer service center if you need additional assistance. Have the following info ready: - Product name and serial number - Description of your software (OS, version, software, etc.)
- Page 5 Safety Instructions Read these safety instructions carefully. Keep this User's Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for clean- ing. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible.
- Page 6 The sound pressure level at the operator's position according to IEC 704- 1:1982 is no more than 70 dB (A). DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein. Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage.
-
Page 7: Table Of Contents
Contents Chapter 1 UNO-1170 Overview ........2 Introduction ............... 2 Hardware Specifications ........... 2 Safety Precautions ............. 3 UNO-1170 Series .............. 4 Chassis Dimensions............4 Figure 1.1:UNO-1170 Chassis Dimensions ....4 Figure 1.2:UNO-1170E Chassis Dimensions ....5 Chapter 2 Hardware Functionality ......... 8 UNO-1170 Peripherals............ - Page 8 DIN-rail Mounting Setup ..........29 Wallmounting Setup............30 Appendix A System Settings and Pin Assignments ..32 Board Connectors and Jumpers........34 Figure A.1:Connector & Jumper Locations (Top) ..34 Figure A.2:Connector & Jumpers (UNO-1170E) ..36 RS-232 Serial Port (COM1~COM2)....... 37 RS-232/422/485 Serial Port (COM3)......
- Page 9 UNO-1170 Overview Sections include: • Introduction • Hardware Specifications • Safety Precautions • UNO-1170 Series • Chassis Dimensions...
-
Page 10: Chapter 1 Uno-1170 Overview
Chapter 1 UNO-1170 Overview 1.1 Introduction UNO-1170 is an DIN-rail mounted Embedded Automation Computer, which provides several serial communication ports and Ethernet interfaces. UNO- 1170 is designed with a compact size, small footprint, and help to saves space with its front accessible and DIN-rail design. With rich OS and driver support, such as Windows XP embedded, WinCE 6.0, and even embedded Linux. -
Page 11: Safety Precautions
• Vibration Protection: IEC 68 2-64 (Random 1 Oct./min, 1hr/axis), CompactFlash: 2Grms@ 5~500Hz, (Optional, UNO-1170E only) HDD: 0.5 Grms @ 5~500Hz • Power Supply Voltage: 10-36 VDC, reversed wiring protection • Power Requirement: Min. 48 W (10 ~ 53 VDC) (e.g +24 V @ 2 A) (ATX) •... -
Page 12: Uno-1170 Series
1.4 UNO-1170 Series There are four products in UNO-1170 series, as listed below: UNO-1170 with Intel Celeron M 1.0GHz CPU UNO-1170-C11E and 512MB RAM UNO-1170 with Intel Pentium M 1.4GHz CPU UNO-1170-P12E and 1GB RAM UNO-1170 with Intel Celeron M 1.0GHz CPU, UNO-1170E-C11E 512MB RAM, and PC/104+ expansion UNO-1170 with Intel Pentium M 1.4GHz CPU,... -
Page 13: Figure 1.2:Uno-1170E Chassis Dimensions
Figure 1.2: UNO-1170E Chassis Dimensions... - Page 14 UNO-1170 User Manual...
- Page 15 Hardware Functionality Sections include: •UNO-1170 Peripherals •COM1: RS-232 Interfaces •COM2~3: RS-232/422/485 Interfaces •LAN: Ethernet Connector •Power Connector •LED Indicators •PS/2 Keyboard and Mouse Connector •Universal Serial Bus Connectors •VGA: VGA Display Connector •RESET: Reset Button •Audio • PC/104+ Voltage Selection...
-
Page 16: Chapter 2 Hardware Functionality
Chapter 2 Hardware Functionality 2.1 UNO-1170 Peripherals The following figures show the connectors on UNO-1170. and UNO- 1170E. Information in this chapter is applied to both UNO-1170 and UNO-1170E. Therefore, in this chapter, we just mention UNO-1150 to represent the series product. The following sections give you detailed information about function of each peripheral. -
Page 17: Figure 2.3:Uno-1170E Front View
Figure 2.3: UNO-1170E Front View Figure 2.4: UNO-1157E Top View... -
Page 18: Com1~Com2: Rs-232 Interfaces
COM3 RS-422/485 2.3.1 TI 16C550 UARTs with 16-byte Standard Advantech UNO-1170 comes standard with TI 16C550 UARTs contain- ing 16 bytes FIFOs. These upgraded FIFOs greatly reduce CPU overhead and are an ideal choice for heavy multitasking environments. 2.3.2 Jumperless RS-422/485 In RS-422/485 mode, UNO-1170 automatically sense signals to match RS-422 or RS-485 network. -
Page 19: Rs-232/422/485 Selection
2.3.4 RS-232/422/485 Selection COM2 and COM3 support 9-wire RS-232, RS-422 or RS-485 interfaces, and you can set corresponding jumpers to select serial ports as RS-232 or RS-422/485 interfaces shown in Table 2.2. Please note to reset the system to adapt this configuration change The system detects RS-422 or RS-485 signals automatically in RS-422/ 485 mode. -
Page 20: Terminal Resistor Setup For Rs-422/485
2.3.5 Terminal Resistor Setup for RS-422/485 The onboard termination resistor (120 Ohm) for COM2/COM3 can be used for long distance transmission or device matching. (Default Open.) Each terminal resistor responds to different channels for RS-422/485. Usually, these resistors are needed for both ends of the communication wires and the value of the resistors should match the characteristic imped- ance of the wires used. -
Page 21: Lan: Ethernet Connector
Table 2.4: Auto Flow & Slave/Master Selection SW2 DIP Switch Setting COM Port Mode Selections RS-422: Slave mode COM2 RS-485: Auto flow control RS-422: Slave mode COM3 RS-485: Auto flow control RS-422: Master mode COM2 RS-485: N/A RS-422: Slave mode COM3 RS-485: Auto flow control RS-422: Slave mode... -
Page 22: Led Indicators
2.6 LED Indicators • There are five kinds of LEDs on the UNO-1170 front panel • PWR: system power status • IDE: IDE bus status • Txn, Rxn: Serial communication status of COM Port n • DIAG: a programmable LED indicator to show a systems status •... -
Page 23: Reset: Reset Button
2.10 RESET: Reset Button UNO-1170 provides a reset button on the top of the device. 2.11 Audio UNO-1170 supports audio function with: - Line In - Line Out 2.12 Battery Backup SRAM UNO-1170 provides 512 KB of battery backed SRAM. This ensures that you have a safe place to store critical data. - Page 24 Table 2.5: LED & Buzzer Control Register 210H DIAG LED Register LEDS1 LEDS0 LEDEn 211H Buzzer Register SPKS1 SPKS0 SPKEn LEDEn: =0, DIAG LED disable =1, DIAG LED enable LEDS0 and LEDS1: LED flickering speed setting bit (refer to Table 2.6) SPKEn: =0, Speaker disable =1, Speaker enable...
-
Page 25: Pci/104+ Connectors (Uno-1170E Only)
2.14 PCI/104+ Connectors (UNO-1170E only) UNO-1170E supports up to two PCI/104+ cards. The cards will be installed on connector noted "CN3-A" and "CN3-B". Please check your PC/104+ card support voltage to adjust the jumper on CN4. Table 2.8: PCI-104 Voltage Jumper Settings Voltage Jumper close position setting +3.3V... - Page 26 UNO-1170 User Manual...
- Page 27 Initial Setup Sections include: • CompactFlash Installation • PCI-104 Card Installation (UNO-1170E) • Hard Drive Installation (UNO-1170E) • Chassis Grounding • Power Connection • BIOS Setup and System Assignments...
-
Page 28: Chapter 3 Initial Setup
Chapter 3 Initial Setup 3.1 CompactFlash Card Installation The procedure for installing a CompactFlash card into the UNO-1170/ UNO-1170E is as follows, please follows these steps carefully. Although the outside appearance of the UNO-1170E is different from the figures shownbelow, the procedure is the same. Remove the power. - Page 29 Remove the rear cover. Plug a CompactFlash card with user’s OS and application program into a CompactFlash card slot on board. Screw back the rear cover and the six screws.
-
Page 30: Usb Keypro And Keypro Bracket Installation
3.2 USB Keypro and Keypro Bracket Installation Keep the rear cover removed and have the USB keypro dongle ready. (Note: Only the upper internal USB connector will work. The lower is a dummy connector and won’t have any function) Insert the USB keypro/dongle dongle into internal USB connector and place the keypro bracket as shown in the picture. -
Page 31: Chassis Grounding
Manually adjust the bracket to perfectly fit the USB keypro/dongle. (Note: Due to the extremely compact space in the chassis, the length for USB keypro has to be limited to 45mm) 3.3 Chassis Grounding Please connect the chassis ground of UNO-1170 with "EARTH". Figure 3.1: Chassis Grounding Connection 3.4 Power Connection Connect the UNO-1170 to a 10 ~ 30 VDC power source. -
Page 32: Pc/104+ Card Installation (Uno-1170E)
3.5 PC/104+ Card Installation (UNO-1170E) The procedure for installing a PC/104+ card into the UNO-1170E is shown as following step. Remove the power. Unscrew six screws from UNO-1170E indicated below. UNO-1170 User Manual... - Page 33 Remove the rear cover. Find 2 metal spacer from accessory bag, and screw tight on the location indicated arrow in the below picture. (Note: There were spacers soldered on the daughter board already). Normally you will also get some hexagon spacer from your PCI-104 card packing. Use and screw those spacers on the location indicated black shown in below picture.
- Page 34 Stack the PC/104+ card and related cables. Screw the rear cover and the six screws. Now you are done with the PC/104+ card installation. Note You can use two PC/104+ cards at the same time while you don't use a hard drive. Using a hard drive will limit the number of PC/104+ you used to one UNO-1170 User Manual...
-
Page 35: Hard Drive Installation (Uno-1170E)
3.6 Hard Drive installation (UNO-1170E) The procedure for installing a hard drive into the UNO-1170E is shown as following step. Remove the power. Unscrew six screws from UNO-1170E indicated below. Remove the rear cover. Please refer to Section 3.1 & 3.2 for the instruction to open the cover. - Page 36 Turn the hard drive bracket and align with the screw hole on the rear cover. Use the four screws taken from step 4 and screw the bracket and the rear cover tight. Connect the other end of SATA cable on the board which the arrow indicated in below picture.
-
Page 37: Bios Setup And System Assignments
3.7 BIOS Setup and System Assignments UNO-1170 uses the Advantech SOM-4481 and SOM-4486 CPU module. For UNO-1170 BIOS setup and system assignments, you can refer to SOM-4481 and SOM-4486 Chapter 4 “Award BIOS Setup” and Appen- dix A “System Assignments”. The SOM-4481 & SOM-4486's user’s manual is in the “Manual”... -
Page 38: Wallmounting Setup
3.9 Wallmounting Setup Please follow the below steps to mount the UNO-1170 on the wall. Screw the provided Wall Mounting Kit on the rear side of UNO- 1170 as the diagram shown below. Mount the device on the wall by the 2 pairs hooking hole provided by the Wallmounting Kit. -
Page 39: Pin Assignments
System Settings and Pin Assignments •Board Connectors and Jumpers •RS-232 Serial Port (COM1~2) •RS-232/422/485 Serial Port (COM3) •Ethernet RJ-45 Connector •Power Screw Terminal •PS/2 Keyboard and Mouse Connector •USB Connector •VGA Display Connector •CompactFlash Master/Slave Jumper Setting •SATA DATA Connector... -
Page 40: Appendix A System Settings And Pin Assignments
Appendix A System Settings and Pin Assignments A.1 System I/O Address & Interrupt Assignments Table A.1: UNO-1170 System I/O Ports Address Range Device 000-01F DMA controller (slave) 020-03F Interrupt controller 1, (master) 040-05F 8254 timer/counter 060-06F 8042 (keyboard controller) 070-07F Real-time clock, non-maskable interrupt (NMI)mask 080-09F DMA page register,... - Page 41 Table A.2: UNO-1170 Interrupt Assignment Interrupt No. Interrupt Source Parity error detected IRQ 0 Interval timer IRQ 1 Keyboard IRQ 2 Interrupt from controller 2 (cascade) IRQ 3 COM2 IRQ 4 COM1 IRQ 5 Available IRQ 6 Diskette controller (FDC) IRQ 7 Available IRQ 8...
-
Page 42: Board Connectors And Jumpers
A.2 Board Connectors and Jumpers There are connectors and jumpers on the UNO-1170 board. The follow- ing sections tell you how to configure the UNO-1170 hardware setting. Figure A-1 and figure A-2 show the locations of UNO-1170 connectors and jumpers. Figure A.1: Connector &... - Page 43 Table A.3: Connectors & Jumpers Lithium battery for BIOS Lithium battery for Backup SRAM Power Screw Terminal Clear COMS Jumper USB connector VGA DB15 display connector/ COM3 RS-232/422/485 PS/2 keyboard and mouse connector Internal USB dongle connector Internal CompactFlash card slot COM1 RS-232 serial port / COM2 RS-232 serial port CN10 Ethernet port 1 / Ethernet port 2...
-
Page 44: Figure A.2:Connector & Jumpers (Uno-1170E)
Figure A.2: Connector & Jumpers (UNO-1170E) Table A.4: Connectors & Jumpers (UNO-1170E) CN3-B,CN3-C PC/104 card connector CN3-A PCI-104 card connector Mini PCI card connector Jumper of PCI-104 card voltage selection (+3.3V or +5V) UNO-1170 User Manual... -
Page 45: Rs-232 Serial Port (Com1~Com2)
A.3 RS-232 Serial Port (COM1~COM2) Table A.5: RS-232 Serial Port Pin Assignments Signal Name... -
Page 46: Rs-232/422/485 Serial Port (Com3)
A.4 RS-232/422/485 Serial Port (COM3) Table A.6: RS-232/422/485 Serial Ports RS-232 RS-422 RS-485 DATA- DATA+ A.5 Ethernet RJ-45 Connector (LAN1~LAN2) Table A.7: Ethernet RJ-45 Connector Pin Assigns 10/100Base-T Signal Name XMT+ XMT- RCV+ RCV- UNO-1170 User Manual... -
Page 47: Power Screw Terminal (Cn8)
A.6 Power Screw Terminal (CN8) Table A.8: Phoenix Power Connector Pin Assigns Signal Name VIN ( 10 ~ 36 VDC ) Field Ground A.7 PS/2 Keyboard and Mouse Connector (CN10) Table A.9: Table A.10: Keyboard & Mouse Connector Pin Assigns Signal Name KB DATA MS DATA... -
Page 48: Usb Connector (Cn13)
A.8 USB Connector (CN13) Table A.11: USB Connector Pin Assignments Signal Name Cable Color DATA- White DATA+ Green Black A.9 VGA Display Connector (CN15) Table A.12: VGA Adaptor Cable Pin Assignments Signal Name Signal Name EDID Power GREEN BLUE H-SYNC V-SYNC Display Memory With 64MB share memory, the VGA controller can drive CRT displays or... -
Page 49: Sata Data Connector (Cn17)
A.10 SATA Data Connector (CN17) Table A.13: SATA DATA Connectors (CN17) Signal Name... - Page 50 UNO-1170 User Manual...
- Page 51 Programming the Watchdog Timer...
-
Page 52: Appendix B Programming The Watchdog Timer
Appendix B Programming the Watchdog Timer Below are samples of code for controlling the Watchdog Timer function. ----------------------------------------------------------------------------------- Enter the extended function mode, interruptible double-write | ----------------------------------------------------------------------------------- MOV DX,2EH MOV AL,87H OUT DX,AL OUT DX,AL ----------------------------------------------------------------------------- Configured logical device 8, configuration register CRF6 | ----------------------------------------------------------------------------- MOV DX,2EH MOV AL,2BH OUT DX,AL MOV DX,2FH IN AL,DX...