Fastlane Pool Equipment Hutch Assembly; Installing An Antenna Extension; Remote Control Transmitter - Endless Pools Fastlane Installation Manual And User's Manual

A #8AWG bare copper wire is required for all bonding connec-
tions. Connect this wire to your power unit and heater-controller
(if purchased). This wire should then connect to the bonding lug
that was connected to the vertical strut at the front of the pool
(see step 20 of the section called, "Fastlane Swim Unit
Assembly").
FASTLANE POOL EQUIPMENT
HUTCH ASSEMBLY
4
1
Panel 4
Panel 2
Fig. 39
1. Begin by attaching the PVC support (B) to the underside of the
lid (A). Two supports have been provided and are labeled. One
support will be for a 60hz power supply and one support will
be for a 50hz power supply. Choose the support that is appro-
priate for your application. If you are unsure which power sup-
ply you have, refer to the specification plate on the motor.
2. Next, assemble the four vertical panels. The textured side of
the panels will be facing out and each panel will be labeled
on the inside face. Panels 1 and 2 have no tabs on the verti-
cal edges while panels 3 and 4 do. Position the panels so that
1 is opposite 2 and 3 is opposite 4. Align the holes in panels
1 and 2 with the tabs of 3 and 4. Use the shorter screws to
attach the 4 panels together (Fig 39).
3. The underside of the lid will have 1-4 engraved on each side.
Line up the numbers on the underside of the lid with the cor-
responding vertical panel. Use the longer screws to attach the
lid to the vertical face. Make sure that there is a cylindrical
space between the lid and the vertical face at each screw.
4. If optional heater has been ordered then remove the mounting
bracket and adhesive protective film of the heater controller
keypad. Feed the keypad cord into the oval hole in panel 4. Press
the keypad firmly against the panel. Feed the mounting bracket
back over the keypad cord and tighten it against panel 4.
5. Once the Water Quality System is fully assembled, place the
equipment hutch over the entire power unit so that the open-
ing in panel 2 is seated around the power unit controller.
6. Align the 3 holes in the bottom of panel 1 with the holes in
the water quality base. Use the short screws to attach the
17
A 2
3
B
Panel 1
Panel 3
equipment hutch to the base (Fig 40).
Fig. 34

INSTALLING AN ANTENNA EXTENSION

The Fastlane wireless controller transmits radio waves, similar
to a garage door opener. Should the Hydraulic Power Unit
(HPU) be placed too far away from the Fastlane Pool, the wire-
less controller may not be able to perform its functions. To oper-
ate the Fastlane more effectively, it may be helpful to install the
antenna closer to the pool than the HPU, so there is less of a
chance of interference occurring. A longer length of coaxial
cable can be used if needed to move the antenna even closer to
the pool.
Parts List
• Length of coaxial antenna cable
\
• Coaxial grounding block (antenna mount)
Instructions
• If the antenna is already installed, detach it from the upper left
hand side of the Controller Box mounted on the HPU.
• Attach and finger-tighten the antenna cable.
• Attach the coaxial grounding block (antenna mount) within
25ft of the pool.
• The antenna can be placed even closer to the pool by purchas-
ing antenna cable from a local supplier.
• Attach and finger-tighten the antenna to the upper end of the
coaxial grounding block (antenna mount).

REMOTE CONTROL TRANSMITTER

The remote control transmitter has three buttons. Press and hold
the On/Off button to turn the swim current on. Press and hold the
Up or Down button to adjust the current to the desired speed. Press
and hold the On/Off button while the current is on to turn off.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation. WARNING:
Changes or modifications not expressly approved by the
party responsible for compliance could void the user's author-
ity to operate the equipment.