Related Manuals for Endless Pools Swim Spa
Summary of Contents for Endless Pools Swim Spa
- Page 1 O P E R A T I O N S A N D M A I N T E N A N C E E n d l e s s Po o l S w i m S p a...
- Page 2 If a con- crete pad is poured, this is the logical time to “plumb-in” your electrical conduit (refer to the diagram on page 7).
- Page 3 • For health reasons, make sure the spa water is properly • Test the water in your swim spa with a reliable test kit. Add cleaned and disinfected. the necessary chemicals according to the test results and the manufacturer’s instructions.
-
Page 4: Initial Start-Up
If the level is too high, the water can be The level of chlorine inside the swim spa, as long as it is not above prone to “scaling,” when minerals and metals dissolved in the... -
Page 5: Recommended Maintenance Schedule
The acceptable range of Every two months: bromine for your swim spa if 2.0 to 5.0 ppm. The easiest way to • Remove and clean the filter cartridge. After several uses, the introduce Bromine into your Swim Spa is by a floating feeder. A... - Page 6 5 ppm will help, as will maintaining the free chlo- (5) and the 2 bulb o-rings (6) are in place. Connect the new rine level in the swim spa at 3 ppm until the water is clear. bulb to the electrical connector, making sure that the pins in Test the chlorine level frequently during this time.
-
Page 7: Electrical Wiring
An Endless Pool Swim Spa may be used year round, even in cold- er climates. If you will not be using the swim spa during the win- Call an electrician if necessary. ter in an area where freezing is a problem, special consideration... - Page 8 (chlorine or at the swim spa 8" from the back and side of the swim spa bromine). Since the high-efficiency circulating pump is running (220V, 60Amp GFCI).
-
Page 9: Typical Settings
HEATER CONTROLLER Connections simply snap into appropriate color coded receptacles. TYPICAL SETTINGS Set Point : 59°F to 104°F / Factory set at 84°F Filter Cycle Duration: 0 to 24 hrs / Factory set at 24 hrs Jet Pump Run Time: 1 to 255 min. / Factory set at 30 min. Light Timeout: 1 to 255 min. -
Page 10: General Specifications
heat.wav ratings: in.k200 full-function keypad Voltage: 120/240VAC The Quick Reference Card provides a quick overview of your spa’s main functions and the operations accessible with your Current: 17A resistive (4 kW heater at 240V) digital control pad. Frequency: 50 / 60 Hz heat.wav heater flow rate: Spa Functions Minimum of 18 GPM is required... - Page 11 TROUBLESHOOTING SMART WINTER MODE Our Smart Winter Mode protects your system from the cold by An internal hardware error has been detected in turning pumps on several times a day to prevent water from freez- in.xe. Contact Customer Service. ing in pipes. The “Smart Winter Mode”...
- Page 12 Cover Care: The optional 4”-thick bi fold coordinating cover was in an Endless Pool, your workout is continuous and you will tire custom made for your Endless Pool Swim Spa with top of the line faster than when swimming laps in a traditional pool.
- Page 13 Not plugged in. Plug in cord. Light cord not connected. Connect cord. Water Leaks Swim Spa over filled or too many people in spa. Adjust swim spa water level. Couplings or unions loose. Tighten couplers. Incorrect water chemistry. Correct chemistry.
- Page 14 WIRING DIAGRAM: EP-1 CONTROLLER WITH SWIM SPA Line in on 60 amp Ground Fault Circuit Breaker...
- Page 15 All labor costs for removal and re-installation of the defective part and all freight charges shall be paid by the purchaser and will not be reimbursed by Endless Pools, Inc. This warranty is expressly in lieu of all other warranties...
- Page 16 Endless Pools, Inc. • 1601 Dutton Mill Rd • Aston, PA 19014-2931 800-910-2714 • 610-497-8693 fax • www.myendlesspool.com B31 5-09...
Need help?
Do you have a question about the Swim Spa and is the answer not in the manual?
Questions and answers