Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Edimax ECS1100 Series
Summary of Contents for Edimax ECS1100 Series
- Page 1 ECS1100 Series We b M a na ge m en t Gu id e Release v1.0.1.0 www.edge-core.com...
- Page 2 Web Management Guide ECS1100-5P L2 Gigabit Ethernet Web Managed PoE Switch with 4 1000BASE-T RJ-45 PoE+ (30W) Ports, and 1 1000BASE-T RJ-45 Port ECS1100-10HP L2 Gigabit Ethernet Web Managed PoE Switch with 4 1000BASE-T RJ-45 PoE++ (90W) Ports, 4 1000BASE-T RJ-45 PoE+ (30W) Ports, and 2 100/1000M SFP Ports E082023-CS-R01...
-
Page 3: How To Use This Guide
How to Use This Guide This guide includes detailed information on the switch software, including how to operate and use the management functions of the switch. To deploy this switch effectively and ensure trouble-free operation, you should first read the relevant sections in this guide so that you are familiar with all of its software features. - Page 4 How to Use This Guide Caution: Alerts you to a potential hazard that could cause loss of data, or damage the system or equipment. Warning: Alerts you to a potential hazard that could cause personal injury. Revision History This section summarizes the changes in each revision of this guide. August 2023 Revision This is the first version of this guide.
-
Page 5: Table Of Contents
Contents How to Use This Guide Contents Section I Getting Started 1 Using the Web Interface Connecting to the Web Interface Navigating the Web Browser Interface Dashboard Configuration Options Saving the Configuration Panel Display Main Menu Section II Web Configuration 2 System Management System Information IP Settings... - Page 6 Contents Port Speed Limit Port Trunk Port Statistics 4 VLAN Configuration Static VLAN VLAN Setting 5 QoS Configuration QoS Basic QoS Advanced Port-Based Priority 802.1p-Based Priority DSCP-Based Priority Priority Queue Mapping 6 PoE Configuration PoE Port Config PoE System Power PD Alive PoE Timer Rule PoE Timer Set...
- Page 7 Contents Section III Appendices A Troubleshooting Problems Accessing the Management Interface B License Information The GNU General Public License – 7 –...
-
Page 8: Section I
Section I Getting Started This section describes the basic settings required to access the management interface. This section includes these chapters: “Using the Web Interface” on page 9 – 8 –... -
Page 9: Using The Web Interface
Using the Web Interface This switch provides an embedded HTTP web management interface. Using a web browser you can configure the switch and view statistics to monitor network activity. The web management interface can be accessed by any computer on the network using a standard web browser. -
Page 10: Navigating The Web Browser Interface
Chapter 1 | Using the Web Interface Navigating the Web Browser Interface Navigating the Web Browser Interface To access the web-browser interface you must first enter a user name and password. The administrator has read/write access to all configuration parameters and statistics. -
Page 11: Saving The Configuration
Chapter 1 | Using the Web Interface Navigating the Web Browser Interface Table 1: Web Page Configuration Buttons (Continued) Button Action Refreshes screen information. Clears all current information. Adds or modifies a table entry. Ends the current web management session. Saving the The switch configuration settings are not automatically saved by the system for Configuration... -
Page 12: Main Menu
Chapter 1 | Using the Web Interface Navigating the Web Browser Interface Main Menu Using the web interface, you can define system parameters, manage and control the switch, and all its ports, or monitor network conditions. The main menu is organized as follows: System Management —... -
Page 13: Web Configuration
Section II Web Configuration This section describes switch configuration features, along with a description of how to configure each feature via a web browser. This section includes these chapters: “System Management” on page 14 “Port Configuration” on page 22 ... -
Page 14: System Management
System Management The system management pages are used to control IP settings, user names and passwords, system time, and display or configure a variety of other system information. This chapter describes the following topics: System Information — Displays basic switch information, including hardware ... -
Page 15: Ip Settings
Chapter 2 | System Management IP Settings Gateway — The default gateway address for destinations not found in local routing tables. (Default: None) Firmware Version — The version number of the runtime code. Firmware Date — The date of the runtime code. ... - Page 16 Chapter 2 | System Management IP Settings Parameters The following parameters are displayed: DHCP Setting — Specifies whether IP functionality is enabled via the Dynamic Host Configuration Protocol (DHCP). If DHCP is enabled, IP will not function until a reply has been received from the server. Requests will be broadcast periodically by the switch for an IP address.
-
Page 17: Account Settings
Chapter 2 | System Management Account Settings Account Settings Use the System Management > Account Settings page to control management access to the switch based on a manually configured user name and password. Usage Guidelines The default administrator name is “admin” with the password “admin.” ... -
Page 18: System Time
Chapter 2 | System Management System Time System Time The Simple Network Time Protocol (SNTP) allows the switch to set its internal clock based on periodic updates from a time server. Maintaining an accurate time on the switch enables the system log to record meaningful dates and times for event entries. -
Page 19: Setting The Time Using Sntp
Chapter 2 | System Management System Time Setting the Time Use the System Management > System Time page to set the system time on the Using SNTP switch using SNTP. Parameters The following parameters are displayed: Time Mode Setting — Selects “manual” or “sntp” for setting the time. ... -
Page 20: Cloud Manage
Chapter 2 | System Management Cloud Manage Cloud Manage Use the System Management > Cloud Manage page to configure the cloud management agent on the switch for management through ecCLOUD. Edgecore ecCLOUD is a cloud-based network service available from anywhere through a web-browser interface. -
Page 21: Jumbo Frames
Chapter 2 | System Management Jumbo Frames Jumbo Frames Use the System Management > Jumbo Frames page to configure support for layer 2 jumbo frames. The switch provides more efficient throughput for large sequential data transfers by supporting jumbo frames up to 15K bytes. Compared to standard Ethernet frames that run only up to 1.5 KB, using jumbo frames significantly reduces the per-packet overhead required to process protocol encapsulation fields. -
Page 22: Port Configuration
Port Configuration The port configuration pages are used to display or set communication parameters for Ethernet ports, configure trunks, and set storm control or port speed limits. This chapter describes the following topics: Port Settings — Configures connection settings, including auto-negotiation, or ... - Page 23 Chapter 3 | Port Configuration Port Settings Flow Control — Enables flow control on the port. Flow control can eliminate frame loss by “blocking” traffic from end stations or segments connected directly to the switch when its buffers fill. (Default: Disabled) Nick Name —...
-
Page 24: Storm Control
Chapter 3 | Port Configuration Storm Control Storm Control Use the Port Configuration > Storm Control page to configure broadcast, multicast, and unknown unicast storm control thresholds. Traffic storms may occur when a device on your network is malfunctioning, or if application programs are not well designed or properly configured. -
Page 25: Port Speed Limit
Chapter 3 | Port Configuration Port Speed Limit Set the State for broadcast, unknown multicast, or unknown unicast to enable. Set the threshold level speed for each traffic type. Click Apply. Figure 12: Configuring Storm Control Port Speed Limit Use the Port Configuration > Port Speed Limit page to apply rate limiting to ingress or egress ports. -
Page 26: Port Trunk
Chapter 3 | Port Configuration Port Trunk Speed — Sets the rate limit level in 1000 bits per second. (Range: 1-1000000 kbps; Default: 1000000) Web Interface To configure port speed limits: Click Port Configuration, then Port Speed Limit. Select one or more port numbers. Set the State for ingress and/or egress to enable. - Page 27 Chapter 3 | Port Configuration Port Trunk You can create up to 2 trunks on the switch. The ports at both ends of a connection must be configured as trunk ports. The ports at both ends of a trunk must be configured in an identical manner, ...
-
Page 28: Port Statistics
Chapter 3 | Port Configuration Port Statistics Port Statistics Use the Port Configuration > Port Statistics page to display standard statistics on network traffic. Port statistics display errors on the traffic passing through each port. This information can be used to identify potential problems with the switch or network (such as a faulty port or unusually heavy loading). -
Page 29: Sfp
Chapter 3 | Port Configuration Use the Port Configuration > SFP page to display SFP transceiver information. This page applies only to the ECS1100-10HP switch. Parameters These parameters are displayed: sfpport — The SFP port number. Temperature — The transceiver working temperature. ... -
Page 30: Vlan Configuration
VLAN Configuration A VLAN is a group of ports that can be located anywhere in the network, but communicate as though they belong to the same physical segment. The VLAN pages in the web interface describe how to create VLAN groups, add port members, and specify how VLAN tagging is used. -
Page 31: Vlan Setting
Chapter 4 | VLAN Configuration VLAN Setting Untagged — A port is a member of the VLAN. All packets transmitted by the port will be untagged, that is, not carry a VLAN tag. Tagged — A port is a member of the VLAN. All packets transmitted by the port ... - Page 32 Chapter 4 | VLAN Configuration VLAN Setting Parameters These parameters are displayed: Management VLAN — The VLAN that allows access to the switch web interface. (Default: 1) Port — Lists the switch port numbers. PVID — The VLAN ID assigned to untagged frames received on the port. ...
-
Page 33: Qos Configuration
QoS Configuration Quality of Service (QoS) allows you to specify which data packets have greater precedence when traffic is buffered in the switch due to congestion. This switch supports QoS with eight priority queues for each port. Data packets in a port’s high-priority queue will be transmitted before those in the lower-priority queues. - Page 34 Chapter 5 | QoS Configuration QoS Basic Parameters These parameters are displayed: Queue ID — The ID of the priority queue. (Range: 0-7) Strict — Services the egress queues in sequential order, transmitting all traffic in the higher priority queues before servicing lower priority queues. This ensures that the highest priority packets are always serviced first, ahead of all other traffic.
-
Page 35: Qos Advanced
Chapter 5 | QoS Configuration QoS Advanced QoS Advanced Use the QoS > QoS Advanced page to select between using port-based, 802.1p- based, or DSCP-based priority QoS modes, as well as mapping QoS priorities to port priority queues. The default QoS mode is 802.1p-based priority. Port-Based Priority Use the Port-Based QoS Mode page to specify the default port priority for each port on the switch. -
Page 36: 802.1P-Based Priority
Chapter 5 | QoS Configuration QoS Advanced Figure 20: Configuring Port-Based Priority 802.1p-Based Use the 802.1p-Based QoS Mode page to show the mapping of 802.1p priority Priority values of incoming frames to internal priorities on the switch. The priority levels recommended in the IEEE 802.1p standard for various network applications are shown in Table 2. -
Page 37: Dscp-Based Priority
Chapter 5 | QoS Configuration QoS Advanced Select 802.1p Based for the QoS Mode. Click Apply. Figure 21: Configuring 802.1p-Based Priority DSCP-Based Priority Use the DSCP-Based QoS Mode page to map DSCP values in incoming frames to QoS values for internal priority processing. The switch supports a common method of prioritizing layer 3/4 traffic to meet application requirements. -
Page 38: Priority Queue Mapping
Chapter 5 | QoS Configuration QoS Advanced Click Apply. Figure 22: Configuring DSCP-Based Priority Priority Queue Use the QoS > QoS Advanced page to map QoS values in packets to switch port Mapping priority queues. Parameters These parameters are displayed: Priority —... - Page 39 Chapter 5 | QoS Configuration QoS Advanced Figure 23: Configuring Priority Queue Mapping – 39 –...
-
Page 40: Poe Configuration
PoE Configuration The switch can provide DC power to a wide range of connected devices, eliminating the need for an additional power source and cutting down on the amount of cables attached to each device. Once configured to supply power, an automatic detection process is initialized by the switch that is authenticated by a PoE signature from the connected device. - Page 41 Chapter 6 | PoE Configuration PoE Port Config The total PoE power delivered by all ports cannot exceed the maximum power budget of the switch. The maximum number of ports that can supply power simultaneously at the specified levels are shown in the following table. Table 3: Maximum Number of Ports Providing Simultaneous Power Maximum Port Power ECS1100-5P Max Ports...
-
Page 42: Poe System Power
Chapter 6 | PoE Configuration PoE System Power Select one or more ports in the Port list. Set the Control to enable or disable. Click Apply. Figure 24: Configuring Port PoE PoE System Power Use the PoE > PoE System Power page to view the current status of PoE power usage on the switch. -
Page 43: Pd Alive
Chapter 6 | PoE Configuration PD Alive Figure 25: Displaying PoE System Power PD Alive Use the PoE > PD Alive page to configure periodic checking of connected PoE powered devices. Parameters These parameters are displayed: Port — Selects a port number. ... -
Page 44: Poe Timer Rule
Chapter 6 | PoE Configuration PoE Timer Rule Figure 26: Configuring PD Alive Management PoE Timer Rule Use the PoE > PoE Timer Rule page to configure daily time limits during which PoE power is available on ports. Usage Guidelines PoE timer rules can be configured only after setting the system time. -
Page 45: Poe Timer Set
Chapter 6 | PoE Configuration PoE Timer Set Figure 27: Configuring PoE Timer Rules PoE Timer Set Use the PoE > PoE Timer Set page to assign configured timer rules to specific ports. Usage Guidelines PoE timer rules can only take effect after setting the system time. ... -
Page 46: Poe Extend Mode
Chapter 6 | PoE Configuration Poe Extend Mode Click Apply. Figure 28: Assigning PoE Timer Rules to Ports Poe Extend Mode Use the PoE > PoE Extend Mode page to configure ports for a long-reach mode of operation where the transmission distance can be extended up to 250 meters. Usage Guidelines When PoE Extend Mode is enabled on a port, the transmission distance can be ... - Page 47 Chapter 6 | PoE Configuration Poe Extend Mode Select one or more ports from the Port list. Set Extend Mode to enabled. Click Apply. Figure 29: Assigning PoE Timer Rules to Ports – 47 –...
-
Page 48: Igmp Configuration
IGMP Configuration This switch can use Internet Group Management Protocol (IGMP) to filter multicast traffic. IGMP Snooping can be used to passively monitor or “snoop” on exchanges between attached hosts and an IGMP-enabled device, most commonly a multicast router. In this way, the switch can discover the ports that want to join a multicast group, and set its filters accordingly. -
Page 49: Router Port
Chapter 7 | IGMP Configuration Router Port VLAN ID for IGMP Snooping — Selects the VLAN which is to propagate all multicast traffic coming from the attached multicast router. Web Interface To enable or disable IGMP: Click IGMP, then IGMP Snooping. Set the IGMP Snooping Setting to Enable. - Page 50 Chapter 7 | IGMP Configuration Router Port VLANs — Selects the VLAN that is to propagate all multicast traffic coming from the attached multicast router. (Range: 1-4094) Static Router Port — Lists the VLAN, Port, and Type (static or dynamic) for ...
-
Page 51: Group Address
Chapter 7 | IGMP Configuration Group Address Group Address Use the IGMP > Group Address page to statically assign a multicast service to a port on the switch. Usage Guidelines Multicast filtering can be dynamically configured using IGMP Snooping, but in ... - Page 52 Chapter 7 | IGMP Configuration Group Address Figure 32: Configuring Static Multicast Group Addresses – 52 –...
-
Page 53: Tools
Tools The switch provides tools for upgrading the system software, backing up and restoring the configuration, resetting the switch to factory defaults, and restarting the switch. This chapter describes the following topics: System Upgrade — Upgrades the switch operating software. ... -
Page 54: Backup Restore
Chapter 8 | Tools Backup Restore Click the Select File button and locate the upgrade file. Click the Upload button. When the upgrade is complete, reboot the switch. Figure 33: Upgrading the System Software Backup Restore Use the Tools > Backup Restore page to save the current switch configuration, backup the configuration file, and restore a previously saved configuration. - Page 55 Chapter 8 | Tools Backup Restore Select File — Selects a previously saved configuration file stored on the management station. Configuration Restore — Uploads a configuration file and replaces the current switch configuration. Web Interface To backup a switch configuration: Click Tools, then Backup Restore.
-
Page 56: System Reset
Chapter 8 | Tools System Reset System Reset Use the Tools > System Reset page to reset the switch configuration to factory defaults and restart the system. Usage Guidelines The reset operation resets the entire switch system. It can take a few minutes to reset the switch. Do not try to perform other ... - Page 57 Chapter 8 | Tools System Reboot Parameters These parameters are displayed: Reboot — Restarts the system immediately. Web Interface To restart the switch: Click Tools, then System Reboot. Click Reboot to restart the system. When prompted, confirm that you want to reboot the switch. When prompted, confirm that you want save the current switch configuration.
-
Page 58: Appendices
Section III Appendices This section provides additional information and includes these items: “Troubleshooting” on page 59 “License Information” on page 60 – 58 –... -
Page 59: A Troubleshooting
Troubleshooting Problems Accessing the Management Interface Table 4: Troubleshooting Chart Symptom Action Cannot connect using a Be sure the device is powered up. web browser Check that you have a valid network connection to the switch and that the port you are using has not been disabled. Be sure you have configured the management VLAN through which ... -
Page 60: B License Information
License Information This product includes copyrighted third-party software subject to the terms of the GNU General Public License (GPL), GNU Lesser General Public License (LGPL), or other related free software licenses. The GPL code used in this product is distributed WITHOUT ANY WARRANTY and is subject to the copyrights of one or more authors. - Page 61 Chapter B | License Information The GNU General Public License GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The "Program", below, refers to any such program or work, and a "work based on the Program"...
- Page 62 Chapter B | License Information The GNU General Public License Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange;...
- Page 63 Chapter B | License Information The GNU General Public License If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded.