Table of Contents
Advertisement
CITY SERIES
There are 4 optional stoppers included in the manual pack which provide
additional support to the glass barrier, if desired - install the stoppers prior to
installation of the barrier glass.
7. Slide the glass barrier stopper in as shown below.
8. Slide the side #5 outer panels between the wall and the barrier stopper
3RD ANGLE
PROJECTION
bracket. Repeat steps to install the remaining #5 outer panels using a barrier
stop where required.
DO NOT SCALE
DRAWING
B
UNITS IN INCHES
3RD ANGLE
PROJECTION
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
UNITS IN INCHES
ANGULAR = 1
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
9. Install additional glass stoppers at the end of the unit by sliding the stopper assembly between the unit and panel – the
stopper assembly will attach to the unit via a magnet, adjust position of glass stopper if required.
DETAIL A
SCALE 1 : 12
A
10. Clean the outer panels with a cloth before installing the safety outer barrier glass. To install the safety glass, see this
manual for instructions.
920-477
B
TOLERANCES UNLESS
FIREPLACE PRODUCTS
DETAIL B
OTHERWISE STATED
INTERNATIONAL
SCALE 1 : 4
DIMENSIONS
0.000 = 0.01 CRITICAL
1:24
SCALE:
0.000 = SPECIFIED TOLERANCE
0.000 = 0.031
DWN:
0.000 REF = REFERENCE ONLY
ANGULAR = 1
E.C.N.:
SIGN:
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
TOLERANCES UNLESS
FIREPLACE PRODUCTS
MAT'L :
OTHERWISE STATED
INTERNATIONAL
PROCESS :
1:24
SCALE:
PART :
11/24/2021
DATE:
DWN:
E.C.N.:
SIGN:
DATE:
C
C
3RD ANGLE
TOLERANCES UNLESS
PROJECTION
OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
3RD ANGLE
TOLERANCES UNLESS
FIREPLACE PRODUCTS
UNITS IN INCHES
ANGULAR = 1
PROJECTION
OTHERWISE STATED
INTERNATIONAL
DIMENSIONS
0.000 = 0.01 CRITICAL
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
1:24
SCALE:
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
DWN:
DATE:
0.000 REF = REFERENCE ONLY
UNITS IN INCHES
ANGULAR = 1
E.C.N.:
SIGN:
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
3RD ANGLE
TOLERANCES UNLESS
PROJECTION
OTHERWISE STATED
DIMENSIONS
0.000 = 0.01 CRITICAL
0.000 = SPECIFIED TOLERANCE
DO NOT SCALE
0.000 = 0.031
DRAWING
0.000 REF = REFERENCE ONLY
UNITS IN INCHES
ANGULAR = 1
THIS DRAWING IS THE PROPERTY OF FPI LTD., IT MAY NOT BE COPIED IN WHOLE OR IN PART, OR DISCLOSED TO A THIRD PARTY WITHOUT OUR PRIOR WRITTEN CONSENT.
installation-panels, barriers, faceplates
DETAIL B
SCALE 1 : 4
-
MAT'L :
SHEAR/ PUNCH/ FORM
PROCESS :
CP60 MAIN ASSEMBLY
PART :
11/24/2021
PART NO:
REV:
DATE:
457-500
-
DATE:
-
DETAIL C
SHEAR/ PUNCH/ FORM
SCALE 1 : 8
CP60 MAIN ASSEMBLY
PART NO:
REV:
457-500
-
DETAIL C
SCALE 1 : 8
FIREPLACE PRODUCTS
MAT'L :
INTERNATIONAL
PROCESS :
1:24
SCALE:
PART :
11/24/2021
DATE:
DWN:
-
MAT'L :
E.C.N.:
SIGN:
DATE:
SHEAR/ PUNCH/ FORM
PROCESS :
CP60 MAIN ASSEMBLY
PART :
11/24/2021
PART NO:
REV:
457-500
-
DATE:
SCALE 1 : 12
B
FIREPLACE PRODUCTS
INTERNATIONAL
1:24
2
SCALE:
DWN:
DATE:
E.C.N.:
SIGN:
-
SHEAR/ PUNCH/ FORM
CP60 MAIN ASSEMBLY
PART NO:
REV:
457-500
-
DETAIL B
-
MAT'L :
SHEAR/ PUNCH/ FORM
PROCESS :
CP60 MAIN ASSEMBLY
PART :
City Series CP60E |
11/24/2021
PART NO:
REV:
457-500
-
DATE:
12.02.21
77
Advertisement
Table of Contents
