Related Manuals for Regency City Series New York 40
Summary of Contents for Regency City Series New York 40
- Page 1 MUST READ BEFORE FRAMING IMPORTANT INFORMATION Regency City Series New York 40 CV40E-NG11 / CV40E-LP11 FRAMING DIMENSIONS SPECIFICATIONS HEAT RELEASE REQUIREMENTS QR LINK FOR PDF DIGITAL COPY OF SPECIFICATIONS:...
- Page 2 dimensions CV40E Dimensions Ø 6 3 4 " 21 7 8 " 171mm 556mm Ø 4" 102mm 2'' (51mm) 13'' 3-1/2'' (330mm) Gas Line Entry (89mm) " 18 11 16 " 1016mm 46 1 4 “ " 475mm 17 11 16 " 1175mm 449mm 43"...
-
Page 3: Ventilation Openings
Ventilation Openings Regency's patented Cool Wall system releases warmth at ceiling level. This system reduces excessive radiant heat in front of the fireplace so you can enjoy your fireplace more often. • Design your own chase vent solution to suit your home •... -
Page 4: Installer's Information
to accommodate the chase vent. The top of the chase vent opening must be 3” or less from the top of the chase enclosure. installer's information Chase Enclosure Min 42.25” (1073 mm) When choosing to install the ventilation openings from the front or both sides, The top of the ventilation opening cannot be any lower than 0-3" from the top of the chase enclosure for all installations. -
Page 5: Installation
installation Clearances The clearances listed below are minimum distances unless otherwise stated. A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this fireplace and vent system be installed only in accordance with these instructions. Flue Clearances to Combustibles Clearance: Single Sided Dimension... - Page 6 installation Clearances Floor to ceiling with top ventilation opening Low framing with ventilation opening in front/2 sides or top Full framing with low ventilation opening in front or 2 sides Full framing with ventilation opening in front or 2 sides Note: The ventilation opening may only be placed above, on both sides and in front as shown above.
- Page 7 installation Optional Flush Front Chase Vent Installation - Part #657-991 (White) C40 Chase Vent Framing Clearances This optional flush front chase vent grill is designed so that only the grills are exposed. The 4 flanges in front which secure the chase vent grill to the stud work is covered by the drywall to give a seamless look.
- Page 8 installation C40 Chase Vent Installation Example Frame opening for vent Screw Chase vent to Framing Use at least 3 sets of screws (See Vent Framing Clearances Page) to keep the vent at against framing Drywall Frame wall with nishing material If necessary, mark where the Cut hole in nishing material chase vent is located before...
- Page 9 installation Optional Front Grill Installation - Part #656-991 (Black) This optional grill meets the requirement of the 120 square inches required for the enclosure in all installations and is designed to keep the enclosure cool. In this application, both the flange and screws to secure the grills are exposed as this grill is designed to be installed after the finished facing has been placed on the wall.
-
Page 10: Mantel Leg Clearances
installation Mantel Clearances Combustible mantel clearances from top of front facing are shown in the diagram on the right. 1/2" (13 mm) Drywall, wood, wood panel, etc. 12" (305 mm) 9" (229 m) 5-1/8" (130 mm) Top of Bottomof Fireplace Fireplace Opening 15-1/16”... -
Page 11: Framing Dimensions
installation Framing Dimensions NOTE: Framing may be constructed of combustible material (ie. 2 x 4) and does not require steel studs. Framing Description CV40E Dimensions Framing Height 37-3/8” (949mm) Framing Width 46-3/4" (1187mm) Framing Depth 19" (483mm) Minimum Height to Combustibles 63"(1600mm) Corner Wall Depth 55"... - Page 12 installation Wall Board/Drywall Installation WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as specified. Finishing Instructions It is important to follow the framing and finishing instructions to ensure proper placement of fireplace into the surrounding framing/finishing materials. Wall board materials 1/2 in.
- Page 13 installation Framing and Finishing Inset Installations 1. Frame in the enclosure for the unit with framing material. Note: When constructing the framed opening ensure there is access to install the gas lines,electrical. Also the wiring harness must be wall mounted using the receptacle provided with the appliance.
-
Page 14: Maximum Tv Recess
installation TV Recessed into Wall CB40 Typical Installs CB40 Typical Installs Maximum TV Recess TV Flush with Hearth MAXIMUM TV RECESS FLUSH TV WITH HEARTH MAXIMUM TV RECESS FLUSH TV WITH HEARTH Max 3” (76 mm) Max 3” (76 mm) Max 3”... -
Page 15: City Series
installation CITY SERIES Clean Trim Faceplate Installation CLEAN TRIM FACEPLATE INSTALLATION 1. Frame in fireplace and install finishing material. (Clean Trim Faceplate can 4. Hand bend attachment tabs so they bend past the magnets to the metal accommodate finishing materials for 1/2 inch to 1 1/8".) wall inside the opening.