Table of Contents
Advertisement
2.
Turn the left, center, and right section switches
to the O
position.
N
3.
Turn the master section switch to the O
and look for the following:
•
Ensure that RV anti-freeze flows from the
disconnected end of the pressure-gauge
tube.
•
Spray out the nozzle until the RV anti-freeze
is visible.
4.
Turn the master section switch to the O
position.
5.
Turn the pump switch to the O
6.
Use the boom-section lift switches to raise the
outer boom sections.
Raise the boom sections until they have moved
completely into boom-transport cradle forming
the "X" transport position and the lift cylinders
are fully retracted.
Note:
Make sure that the lift cylinders are fully
retracted to prevent actuator rod damage.
7.
Shut off the engine.
8.
Drain the sprayer tank as completely as
possible.
Long-Term Storage
(Longer than 30 days)
Perform the following procedures found in
Storage (page
91):
1.
Cleaning the Exterior of the Machine (page 91)
2.
Preparing to Condition the Sprayer (page 91)
3.
Conditioning the Sprayer (page 91)
In addition, perform the procedures that follow:
1.
Servicing the Chassis (page 92)
2.
Service the Sprayer (page 92)
3.
Servicing the Engine (page 92)
4.
Servicing the Fuel System (page 92)
5.
Servicing the Battery (page 92)
6.
Protecting the Machine (page 93)
Servicing the Chassis
1.
Check the air pressure in the tires; refer to
Checking the Tire Air Pressure (page
2.
Check the brakes; refer to
(page
74).
3.
Check and tighten all bolts, nuts, and screws.
Note:
Repair or replace any parts that are worn
or damaged.
position
N
FF
position.
FF
Short-Term
25).
Adjusting the Brakes
4.
Paint all scratched or bare metal surfaces
(paint is available from your authorized Toro
distributor).
Service the Sprayer
1.
Clean the agitation valve and the 3 section
valves; refer to
Section Valves (page
2.
Grease the sprayer; refer to
Pump (page
55).
3.
Check the condition of all spray hoses.
Note:
Replace any hoses that are worn or
damaged.
4.
Tighten all hose clamps and fittings.
Servicing the Engine
1.
Service the air cleaner; refer to
Air Cleaner (page
2.
Change the engine-oil filter and oil; refer to
Changing the Engine Oil Filter (page 59)
Changing the Engine Oil (page
Servicing the Fuel System
1.
Drain the fuel tank; refer to
Tank (page
66).
2.
Prepare fuel with fuel stabilizer according to the
manufacturer's instructions, and add it to the
fuel tank.
3.
Start the engine and run it at idle speed for 5
minutes.
4.
Shut off the engine.
5.
Secure all the fuel-system fittings.
Servicing the Battery
1.
Move the machine in a clean, dry storage area.
2.
Remove the battery from the chassis; refer to
Removing the Battery (page
Note:
Do not connect the battery cables to the
battery posts during storage.
3.
Check the electrolyte level.
4.
Fully charge the battery; refer to
Battery (page
Important:
charged to prevent it from freezing and being
damaged at temperatures below 32°F (0°C).
A fully charged battery maintains its charge
for about 50 days at temperatures lower
than 4°C (40°F). If the temperatures will be
above 4°C (40°F), check the water level in the
battery and charge it every 30 days.
92
Cleaning the Agitation and
84).
Greasing the Spray
Checking the
57).
60).
Draining the Fuel
67).
Charging the
68).
The battery must be fully
and
Advertisement
Table of Contents
