Table of Contents
Advertisement
VJ-2638X/1938X/1638X/1938WX/1638WX INSTALLATION MANUAL
4. Peel off the tape, be careful not to come in contact
with T fence, and remove the Bearer collapse
prevention material and Bearer fix.
WARNING
Make sure not to damage T fence during
operation. If T fence is damaged, it will
affect print results.
3
4
2
1
No.
Name
No.
1
Tape
3
Bearer protective material
2
T fence
4
4 Installation
Procedures and environment for installing this product
are explained.
4.1
Installation environment
Install this product to the appropriate place with
reference to the following.
WARNING
Do not install the printer in the following
places where there is a possibility that the
printer may be damaged or might fall or be
fallen by chance.
On a shaky stand
Slanting location
Places where vibration of other
machines etc. is transmitted.
Do not stamp on the printer or do not place
heavy things on top of it. The printer may
be damaged or might fall or be fallen by
chance.
Do not block the vent when covering the
printer with cloths, such as a blanket or
tablecloth.
If the vent is blocked, heat may accumulate
inside the printer and may cause a fire.
Do not install the printer in a location that
has high humidity or is dusty.
It could lead to electric shock and fire.
4.1.1 Installation environmental condition
Select an installation location in accordance with the
table below.
Floor strength of
More than 2940 Pa (300 kg/m
installation place
Rated
VJ-2638X:
voltage
(Main) AC100-240V; 10A-5A
and
(Heater 1/2) AC100-240V; 10A-5A
Consump-
VJ-1938X:
tion
(Main) AC100-240V; 12A-6.5A
Current
(Heater 1/2) AC100-240V; 9A-4.5A
VJ-1638X:
(Main) AC100-240V; 9A-6A
(Heater) AC100-240V; 10A-5A
VJ-1938WX:
AC100-240V; 2.5A-1.0A
VJ-1638WX:
AC100-240V; 2.5A-1A
Rated
50/60Hz
Frequency
Operative
Temperature: 20 °C to 32 °C
condition
Humidity: 40% to 60%, No Condensation
Guaranteed
Temperature: 22 °C to 30 °C
range of
Humidity: 40% to 60%
printing
accuracy
Change
Temperature: within 2 °C per hour
rate
Humidity: within 5% per hour
VJx638xE-I-05
NOTE
For temperature and humidity, avoid locations
such as the following. There is a possibility that
the print quality will be affected.
Places where temperature or humidity may
rapidly change, even though within the required
conditions.
Places that receive direct sunlight, increased illu-
mination or direct air, for example from an air
conditioner.
To keep the temperature and humidity constant,
install this product in a location where the air
condition is adjustable.
4.1.2 Installation space
NOTE
For the weight of the printer and the stand, refer to
1
the Operation Manual.
Install on a level floor which meets the following condition.
It has enough strength to support the weight of the
Name
printer and the stand.
Minimum height:1,550mm
Bearer fix
650mm
VJ-2638X : 3,708mm
VJ-1938X/1938WX : 2,983mm
VJ-1638X/1638WX : 2,698mm
VJ-2638X : 5,400mm
VJ-1938X/1938WX : 4,633mm
VJ-1638X/1638WX : 4,400mm
4.2 Installation procedure
Install this product to the installation place in
accordance with the list shown below.
NOTE
Please check that the butterfly bolts are not loose
before/after carrying this product.
When transferring or carrying outside, separate the
printer and the stand.
1. Check that the eight butterfly bolts attaching the
stand and the printer are not loose.
2. Carry the printer to the installation place.
3. Turn the following adjusters in the direction as
shown below to prevent the printer from moving.
・Adjusters : 4 locations
2
)
No.
1
4. Confirm that the waste fluid valve is closed.
1
No.
1
Waste fluid valve
1,000mm
1
1
Name
No.
Name
Adjuster
2
Stand
Name
4
5. Check that the eight butterfly screws (8 pieces)
attaching the stand and the printer are not loose.
5 Connecting the power cable
This section explains how to connect the power cable.
Follow the steps below to connect the power cable.
WARNING
Be sure to use the specified power cable
(separately sold).
Using power cables other than the
specified can cause an electric shock or
fire.
Use a power cord set which is compati-
ble with the safety standards, power
supply voltage, and plug shape used in
the country where this printer is used.
Use a power cord set which is equipped
with a protective earth, and securely
connect it to the outlet.
Do not use a damaged power cable.
It may cause an electric shock or fire.
1. Confirm that the product is turned OFF.
2. Connect the power cables to the AC inlets on the
rear of the product.
VJ-2638X/1938X : 3 locations
VJ-1638X
VJ-1938WX/1638WX : 1 location
VJ-1638X
No.
Name
1
AC inlet
3. Correctly insert the power cable plug into the power
socket.
NOTE
To use the two power cables plugged in
the inlets, total capacity described below is
2
required. If the power source cannot supply
the required capacity, plug the two or more
power cables in the different power sources
1
respectively.
VJ-2638X: at "EcoMode" : 26A or more
at "Powerful" : 30A or more
VJ-1938X
VJ-1638X
VJ-1938WX/1638WX
1
No.
1
Power cable
VJ-2638X/
1
1938X
: 2 locations
1
2
1
VJ-1938WX
VJ-1638WX
2
2
No.
Name
2
Power cable
: 30A or more
: 19A or more
: 2.5A or more
Name
Advertisement
Table of Contents
