Installation Space; Connecting The Power Cable; Installation Environment; Installation Procedure - MUTOH VJ-1624 Installation Manual

VJ-1624 INSTALLATION MANUAL
3. Peel off the tape, be careful not to come in contact
with T fence, and remove the Bearer collapse pre-
vention material and Bearer fix.
WARNING
Make sure not to damage T fence dur-
ing operation.
If T fence is damaged, it will affect
print results.
3 4
2
1
No. Name No.
1 Tape 2
3 Bearer protective material 4
4 Installation
Procedures and environment for installing this product
are explained.

4.1 Installation environment

Install this product to the appropriate place with refer-
ence to the following.
WARNING
Do not install the printer in the follow-
ing places where there is a possibility
that the printer may be damaged or
might fall or be fallen by chance.
On a shaky stand
Slanting location
Places where vibration of other machines
etc. is transmitted.
Do not stamp on the printer or do not
place heavy things on top of it. The
printer may be damaged or might fall
or be fallen by chance.
Cover the printer with blanket and cloth
like tablecloth and do not close the vent.
If the vent is closed, the printer could
accumulate heat inside and may cause
fire.
Do not install the printer in a location
that has high humidity or is dusty.
It could lead to electric shock and fire.
VJ1624E-I-00
4.1.1 Installation environmental condition
Select an installation location in accordance with the
table below.
Floor strength of
installation place
Power Power
Specifica- Supply
tion
Frequency
Range
Power
capacity
Environm-
Operative
ental
condition
conditions
Guaranteed
range of
printing
accuracy
Change
rate
NOTE
For temperature and humidity, avoid locations
such as the following. There is a possibility that
1
the print quality will be affected.
Places where temperature or humidity may
rapidly change, even though within the required
conditions.
Places that receive direct sunlight, increased illu-
mination or direct air, for example from an air
Name
conditioner.
T fence
To keep the temperature and humidity constant, in-
Bearer fix
stall this product in a location where the air condi-
tion is adjustable.
4.1.2

Installation space

Install on a level floor which meets the following condition.
It has enough strength to support the weight of the
printer and the stand.
NOTE
For the weight of the printer and the stand, refer to
the Operation Manual.
a
f
4.2

Installation procedure

Install this product to the installation place in accord-
ance with the list shown below.
NOTE
Please check that the butterfly bolts are not loose
before/after carrying this product.
When transferring or carrying outside, separate the
printer and the stand.
1. Check that the eight butterfly bolts attaching the
stand and the printer are not loose.
More than 2940 Pa (300 kg/m )
2
AC 90 V to 132 V / 198 V to 264 V
50/60Hz ± 1Hz
Main: 12A
Heater: 12A
Temperature: 20 °C to 32 °C
Humidity: 40 % to 60 %, No Condensation
Temperature: 22 °C to 30°C
Humidity: 40 % to 60 %
Temperature: within 2 °C per hour
Humidity: within 5 % per hour
a= 650 mm
b=1,000 mm
c=1,000 mm
d=1,000 mm
e=1,550 mm
f =3,800 mm
g=2,700 mm
e
d
c
b
g
4
2. Carry the printer to the installation place.
3. Turn the following adjusters in the direction as
shown below to prevent the printer from moving.
・Adjusters : 4 locations
1
1
No. Name No.
1 Adjuster 2
4. Confirm that the waste fluid valve is closed.
1
No. Name
1 Waste fluid valve
5. Check that the eight butterfly bolts (8 pieces) at-
taching the stand and the printer are not loose.

5 Connecting the power cable

This section explains how to connect the power cable.
Follow the steps below to connect the power cable.
WARNING
Be sure to use the specified power cable
(separately sold).
Using power cables other than the specified
can cause an electric shock or fire.
Use a power cord set which is compatible
with the safety standards, power supply
voltage, and plug shape used in the country
where this printer is used.
Use a power cord set which is equipped
with a protective earth, and securely con-
nect it to the outlet.
Do not use a damaged power cable.
It may cause an electric shock or fire.
1. Confirm that the product is turned OFF.
2
1
Name
Stand