Installation Environment; Installation Space; Installation Procedure; Connecting The Power Cable - MUTOH VJ-1204 Installation Manual

VJ-1204 INSTALLATION MANUAL
4 Installation
Procedures and environment for installing this product
are explained.

4.1 Installation environment

Install this product to the appropriate place with refer-
ence to the following.
WARNING
Do not install the printer in the follow-
ing places where there is a possibility
that the printer may be damaged or
might fall or be fallen by chance.
On a shaky stand
Slanting location
Places where vibration of other machines
etc. is transmitted.
Do not stamp on the printer or do not
place heavy things on top of it. The
printer may be damaged or might fall
or be fallen by chance.
Cover the printer with blanket and
cloth like tablecloth and do not close
the vent. If the vent is closed, the print-
er could accumulate heat inside and
may cause fire.
Do not install the printer in a location
that has high humidity or is dusty.
It could lead to electric shock and fire.
4.1.1 Installation environmental condition
Select an installation location in accordance with the
table below.
Floor strength of More than 2940 Pa (300 kg/m
installation place
Power Power AC90V - 132V/198V - 264V
Specifica- Supply
tion
Frequency
50/60Hz ± 1Hz
Range
Power
More than 10 A
capacity
Environm-
Operative Temperature:20 °C to 32 °C
ental
condition Humidity: 40 % to 60 %, No Condensation
conditions
Guaranteed
Temperature:22 °C to 30°C
range of
Humidity: 40 % to 60 %
printing
accuracy
Change Temperature: within 2 °C per hour
rate Humidity: within 5 % per hour
Archiving Temperature:-20° C to 60 °C
environment Humidity: 5 % to 85 % ,
No Condensation (Ink unfilled)
NOTE
For temperature and humidity, avoid locations
such as the following. There is a possibility that
the print quality will be affected.
Places where temperature or humidity may
rapidly change, even though within the required
conditions.
Places that receive direct sunlight, increased illu
mination or direct air, for example from an air
conditioner.
To keep the temperature and humidity constant, in-
stall this product in a location where the air condi-
tion is adjustable.
VJ1204E-I-00
4.1.2

Installation space

Install on a level floor which meets the following con-
dition.
It has enough strength to support the weight of the
printer and the stand.
NOTE
For the weight of the printer and the stand, refer to
the Operation Manual.
a=180mm
b=450mm
c=480mm
d=300mm
e=1198mm
a
4.1.3

Installation procedure

Install this product to the installation place in accord-
ance with the list shown below.
NOTE
Please check that the butterfly bolts are not loose
before/after carrying this product.
When transferring or carrying outside, separate the
printer and the stand.
1. Check that the two butterfly bolts attaching the
stand and the printer are not loose.
2. Carry the plotter to the installation place.
3. Lock two casters on the front side.
)
2
No. Name
1 Casters
4. Check that the two butterfly bolts attaching the
stand and the printer are not loose.
e
d
c
b
1
2
No. Name
2 Caster locks
4

5 Connecting the power cable

This section explains how to connect the power cable.
WARNING
Make sure that the included power ca-
ble is used.
If other power cables are used, it may
cause an electric shock or fire.
Do not use a damaged power cable. It
may cause an electric shock or fire.
Follow the steps below to connect the power cable.
1. Confirm that the product is turned OFF.
NOTE
If the [Power] key is pressed, the product is turned
ON. Press the key again, and turn OFF the power.
No. Name
1 AC inlet
2. Connect the power cable to the AC inlet on the
back of the product.
1
No. Name
1 Power cable
3. Correctly insert the power cable plug into the pow-
er socket.
1
2