Understanding Reverse Speeds; Understanding Displayed Traction Speeds; Understanding The Power Match System; During Operation - Toro Reelmaster 5010-H Operator's Manual

2. Drive the machine at the maximum transport
speed of 16 km/h (10 mph) and remove your
foot at the start of the 3.7 m (12 ft).
3. Check if the machine stops within 0.6 m (2 ft) of
the end mark (3.7 m or 12 ft).
4. Contact your Toro distributor if the stopping
distance of the machine is not within 0.6 m (2
ft) of this distance.
Understanding Reverse
Speeds
Transport Reverse Speed
•
If the maximum transport speed set by the
supervisor is above 8.0 km/h (5.0 mph), the
maximum reverse speed is 8.0 km/h (5.0 mph).
•
If the maximum transport speed set by the
supervisor is at or below 8.0 km/h (5.0 mph),
maximum reverse speed is equal to the transport
speed set by the supervisor.
Mowing Reverse Speed
•
If the maximum mow speed set by the supervisor
is above 6.4 km/h (4.0 mph), the maximum reverse
speed is 6.4 km/h (4.0 mph).
•
If the maximum mow speed set by the supervisor
is at or below 6.4 km/h (4.0 mph), maximum
reverse speed is equal to the transport speed set
by the supervisor.
Understanding Displayed
Traction Speeds
This machine displays estimated traction speeds in
kilometers per hour (km/h) or miles per hour (mph).
•
The instantaneous speed is displayed in the upper
left-hand corner of the cruise control and virtual
pedal stop screens.
•
The traction speeds are estimated, and calibrated
to be most accurate at 8.0 km/h (5.0 mph) while
mowing. Displayed speeds are accurate when it
is 0.8 km/h (0.5 mph) above or below the display
speed while driving on dry, flat pavement.
•
Contact your authorized Toro distributor if the
machine's observed speeds deviate more than 2.4
km/h (1.5 mph) from the displayed speeds.
Understanding the Power
Match System
Additional horsepower is supplied on-demand from
the 48-VDC battery pack and is managed by the
PowerMatch ™ system. This additional battery power is
intended for short periods of time—not for continuous
or sustained periods at maximum horsepower.
PowerMatch is made up of 2 different processes:
Understanding Shed Mode
When the horsepower requirement is greater than the
24.8 hp of the engine, the generator will gradually
reduce charge to the batteries and the 48-VDC battery
pack will start driving the reels. This is transparent
to the operator. The generator is shedding its power
requirement from the engine, and the available engine
horsepower can go to the traction hydraulics.
Note:
Toro recommends leaving Shed Mode O
during most operating conditions. To turn off Shed
Mode, use the protected menus in the InfoCenter.
Understanding Boost Mode
When the traction power demand continues to
increase (e.g., driving on steeper hills) the 48-VDC
battery pack powers the generator as an electric
motor to assist the diesel engine, and the 48-VDC
battery pack will also drive the cutting-unit reels.
Note:
Toro recommends leaving Boost Mode O
during most operating conditions. To turn off Boost
Mode, use the protected menus in the InfoCenter.

During Operation

During Operation Safety

General Safety
•
The owner/operator can prevent and is responsible
for accidents that may cause personal injury or
property damage.
•
Wear appropriate clothing, including eye
protection; long pants; substantial, slip-resistant
footwear; and hearing protection. Tie back long
hair and do not wear loose clothing or loose
jewelry.
•
Do not operate the machine while ill, tired, or
under the influence of alcohol or drugs.
•
Use your full attention while operating the
machine. Do not engage in any activity that
causes distractions; otherwise, injury or property
damage may occur.
•
Before you start the engine, ensure that all drives
are in neutral, the parking brake is engaged, and
you are in the operating position.
•
Do not carry passengers on the machine and keep
bystanders and children out of the operating area.
33
N
N