Conair GB User Manual page 111

SPECIFICATIONS
C
MODELS
Performance characteristics
Batch size lbs {g}
Maximum throughput lbs/hr {kg/hr}*
Bin Capacity - Main Ingredient ft
Bin Capacity - Minor Capacity ft
Maximum number of materials
Number of discharge valves
Number of additive feeders
Control Software (# of components)
Dimensions inches {mm}
A - Height above mounting plate
B - Width †
C - Depth †
D - Controller height
E - Controller width
F - Controller depth
Weight lbs {kg}
Installed
Shipping
Voltage Running load amps‡
110V/1 phase/60hz (control)
220V/1 phase/60hz (mixer)
220V/1 phase/60hz (control)
220V/1 phase/60hz (mixer)
220V/1 phase/50hz (control)
220V/3 phase/50hz (mixer)
400V/3 phase/50hz (mixer)
Compressed air requirements
Discharge valves
Maximum loader sizes §
Number of 20 inch loaders
Number of 15 inch loaders
One Conair Drive Pittsburgh, PA 15202
Note: loader
configuration
same for all
models
CONTROL
WSB1840
39.7 {18000} 39.7 {18000}
4114 {1866} 3160 {1433}
3 {liter} 6.7 {189.7}
3 {liter} 3.8 {107.6}
8
4
up to 4
4 or 12
93 {2362.2}
56.25 {1428.8} 56.25 {1428.8}
34.4 {873.8} 34.4 {873.8}
11.25 {285.75} 11.25 {285.75}
12.25 {311.15} 12.25 {311.15}
8.19 {208.03} 8.19 {208.03}
730 {331}
850 {385.5}
0.3
8.2
0.2
8.2
0.2
4.4
2.2
80 psi @ 0.2 ft
1/4 in. NPT fitting
2
4
412-312-6000
GRAVIMETRIC BATCH BLENDERS
WSB 1840, 1850 and 1860 Models
B
WSB1850 WSB1860
39.7 {18000}
2566 {1164}
6.7 {189.7} 3.8 {107.6}
3.8 {107.6} 3.8 {107.6}
9 10
5 6
up to 4 up to 4
12 12
93 {2362.2} 93 {2362.2}
56.25 {1428.8}
34.4 {873.8}
11.25 {285.75}
12.25 {311.15}
8.19 {208.03}
730 {331} 730 {331}
850 {385.5} 850 {385.5}
0.3 0.3
8.2 8.2
0.2 0.2
8.2 8.2
0.2 0.2
4.4 4.4
2.2 2.2
3 /min {5.5 bars @ 0.09 liters/sec}
2 3
5 6
FAX 412-312-6227 www.conairnet.com
TPBS005/0700
C
A
0 0 0
0 0 0
0 0 0
MOUNTING INTERFACE
IB04
(4) 9/16 in. {14.3 mm}
diameter bolt holes
8 in. {203.2 mm}
4 in. {101.6 mm}
diameter square bolt pattern
through hole
14.5 in.
{368.3 mm}
15 in. {381 mm}
20 in. {508 mm}
SPECIFICATION NOTES:
* Maximum throughput rates are based
on using all dispense valves and 35
lb/ft 3 pelletized material. Use of feed-
ers will reduce this rate.
† Feeders will increase width and depth
dimensions. Please refer to feeder
specifications.
‡ Each auger feeder requires an addi-
tional 1 amp @ 120V or 0.5 amp @
240V.
§ Maximum loader sizes may be used
only when the loader is adjacent to
loaders of a smaller diameter.
APPENDIX B
16 in.
{406.4 mm}