Conair GB User Manual page 104

SPECIFICATIONS
GB920
C
D
FEEDER LOCATIONS
NOTE: Any one of the
feeders (A,B,C or D)can be
C
2 1
designated position 5 or 6.
B
A
B
D GB940
C
4
A
C
2
1
3
B
A
B
D C
GB960
8 7 4
C
1 2 3
A
B
B
MODELS
Performance characteristics
Batch size lbs {g}
Maximum throughput lbs/hr {kg/hr}*
Bin capacity - main ingredient
Bin capacity - minor ingredient
Maximum number of materials
Number of discharge valves
Number of additive feeders
Control software (# of components)
Dimensions inches {mm}
A - Height above mounting plate
‡
B - Width
‡
C - Depth
D - Controller height
E - Controller width
F - Controller depth
Weight lbs {kg}
Installed
Shipping
§
Voltage Running load amps
120V/1 phase/60 hz (control and mixer)
220V/1 phase/60 hz (control and mixer)
220V/1 phase/50 hz (control)
220V/3 phase/50 hz (mixer)
400V/3 phase/50 hz (mixer)
Compressed air requirements
Discharge valves
Compressed air feeder
Maximum loader sizes **
Number of 20 inch loaders
Number of 15 inch loaders
One Conair Drive Pittsburgh, PA 15202
B
FRONT VIEW
GB920
GB920 GB940
19.8 {9000} 19.8 {9000}
5200 {2359} 3300 {1497}
ft 3 {liter} 8.5 {240.7} 6.7 {189.7}
NA 3.6 {107.6}
ft 3 {liter}
6
2
up to 4 up to 4
4 or 12 4 or 12
†
74 {1880.7} 74 {1880.7}
56 {1421.4} 56 {1421.4}
34 {863.6} 34 {863.6}
11.25 {285.75} 11.25 {285.75}
12.25 {311.15} 12.25 {311.15}
8.19 {208.03} 8.19 {208.03}
480 {218} 480 {218}
600 {272.2} 600 {272.2}
8.5
4.25 4.25
0.15 0.15
2.2
1.1
80 psi @ 0.2 ft 3 /min {5.5 bars @ 0.09 liters/sec}; 1/4 in. NPT fitting
40 psi @ 2.0 ft 3 /min {2.8 bars @ 0.94 liters/sec}; 1/4 in. NPT fitting
2
2
412-312-6000
GRAVIMETRIC BATCH BLENDERS
AutoWeigh GB900 Series Models
C
A
SIDE VIEW
GB920/GB940
CONTROL
GB960
19.8 {9000}
2124 {965}
3.6 {102.9}
3.6 {107.6}
8 10
4 6
MOUNTING INTERFACE
up to 4
12
74 {1880.7}
56 {1421.4}
34 {863.6}
11.25 {285.75}
12.25 {311.15}
8.19 {208.03}
480 {218}
SPECIFICATION NOTES:
600 {272.2}
* Maximum throughput rates are based on 35 lbft
8.5 8.5
4.25
0.15
† The optional flow control valve will add 6.5 in. {165
2.2 2.2
1.1 1.1
‡ Feeders will increase depth dimensions. Please
§ Each auger feeder requires an additional 1 amp @
2 3
** Maximum loader sizes may be used only when the
4 6
FAX 412-312-6227 www.conairnet.com
B
FRONT VIEW
GB940/GB960
IBO4
pelletized material and using all dispense valves.
Use of feeders for minor ingredients will reduce
this rate. Refer to the selection guide for more
specific throughput information.
mm} to the total height. We recommend using the
flow control valve when mounting the blender to a
stand, surge bin or hopper.
refer to feeder specification.
120V or 0.5 amp @ 240V.
loader is adjacent to loaders of a smaller diameter.
APPENDIX B
TPBS013/1199
C
SIDE VIEW
GB960
3