Page 1
OWNER´S MANUAL Permolock C Locking System for Power Wheelchair in Vehicle...
Page 3
How to contact Permobil Head Office of the Permobil group...
Page 4
Permolock C Locking System for Power Wheelchair in Vehicle Produced and published by Permobil AB, Sweden Edition: 6, 2011-01 Order no.: 205014-US-0...
Owner´s Manual Permolock C Table of Contents Table of Contents Important information about user manual ..........6 Technical Support ................... 7 Spare Parts and Accessories ................7 Warranty and Service ..................7 Safety rules and regulations ..............8-9 Design & Function ..................10 Operation .......................
It is also possible to obtain information concerning our products from our home page on the Internet. You can find us at www.permobil.com. All information, pictures, illustrations and specifications are based upon the product information that was available at the time that these operating instruc- tions were printed.
Owner´s Manual Permolock C Technical support, warranty, etc. TECHNICAL SUPPORT In the event of technical problems, you should contact your dealer or Permobil Inc USA at 1-800-736-0925. Always state the serial number when contacting Permobil to ensure that the correct information is provided.
If the Permolock is involved in an accident of any kind, the locking base, plunger and manual release mechanism must be replaced. An accident can cause damage to the Permolock that you cannot see. WARNING Do not modify the Permolock or use any accessories or parts not specified by Permobil.
Page 9
WARNING To be checked before first use Before using your wheelchair with Permolock C, you must check that the chair has been suitably adjusted. Contact your supplier for information. Failure to properly install and use the Permolock increases the risk of serious injury or death in a sudden stop or crash.
Design & Function General Permolock C consist of two elements. One is a locking device mounted to the wheelchair chassis and operated by a control button on the front edge of the armrest. The second element, a locking plate, is mounted in the vehicle. This is operated by a control button mounted in the vehicle.
Operation Operation General Permolock C is designed to secure an occupied wheelchair in a moving vehicle and is suitable for either the driver or passengers. Permolock C must only be used together with Permobil electric wheelchairs approved for this purpose and with the chair base available as an accessory.
Owner´s Manual Permolock C Operation Operation Locking the wheelchair Permolock C consists of two elements. One is a locking device mounted on the wheelchair chassis and operated by a control button on the front edge of the armrest, see photo.
Page 13
If the lamp is not green, your wheelchair is not secured in the locking plate and could come loose in the event of a collision. 3. After you are correctly locked in the Permolock, fasten your vehicle mounted seat belt. Move the wheelchair in over Permolock C.
CAUTION Always reset the locking mechanism to the locked position after backing the wheelchair off the locking plate. If you do not reset the lock, it will not be ready for relocking. Backing the wheelchair out of Permolock C.
WARNING The user will need assistance in operating the manual emergency release, because in most cases the user will not be able to reach it. Mount the handle and press to the left. Backing the wheelchair out of Permolock C.
Maintenance & Technical specifications Maintenance Cleaning The following is general advice recommended by Permobil. For severe soiling or damage to surface finish, contact Permobil for information. For normal cleaning proceed carefully with a soft cloth/sponge, hot water and a mild detergent. Wipe down carefully with a cloth and water, and dry off.
Owner´s Manual Permolock C Technical specification Technical specifications DATA General Name ................Permolock C Dimensions and weight Length................20” (500 mm.) Width ................17” (425 mm.) Height ................3 1/4 (83 mm.) Weight ................29 Ibs. Electrical system Voltage Permolock ............12V / Car...
Owner´s Manual Permolock C Installation Installation Installation of locking device on the wheelchair chassis (C400, C500) Read through the instructions before starting installation. 1. Remove the wheelchair chassis cover, the right-hand battery and, on Pilot+ models, the main fuse. For a detailed description, see the appropri- ate chassis service manual.
Page 21
Owner´s Manual Permolock C Installation 4. Install the locking device from under- neath the chassis. Use the accom- panying tool to keep the locking device in place, see photo. 5. Install spring, washer and screw from the upper side of the chassis.
Owner´s Manual Permolock C Installation Installation of control electronics on the wheelchair chassis (C400, C500) Read through the instructions before starting installation. 1. Install the control electronics for the locking device in the wheelchair chassis. Guide the electronics box down on the right side of the lock- ing device, see photo.
Page 23
Owner´s Manual Permolock C Installation 6. Chassis with Pilot+ Connect the control electronics to the +24V outlet on the SLS card. If the wheel- chair seat is equipped with an electric actuator, remove the contact for this from the SLS card and instead connect it to the +24V outlet on the cabling for the control electronics, see photo.
Owner´s Manual Permolock C Installation Installation of locking plate in the vehicle General Read through the instructions before starting installation. CAUTION To ensure that the wheelchair locking device ends in the correct position for locking, it is important that the locking plate is mounted correctly in relation to the wheelchair wheels. When mounting on a sloping surface, the locking plate may be raised using spacers to ensure satisfactory engagement and locking.
Owner´s Manual Permolock C Installation Installation of locking plate with standard bracket Read through the instructions before starting installation. 1. Install the four brackets in the standard position (the central hole configuration) on the lock plate, see photo. 2. Position the lock plate correctly in the vehicle.
Page 27
Owner´s Manual Permolock C Installation 6. Position the locking plate correctly on top of the mounting plates. It can be installed in three different positions, ”Standard” or + or - 30 mm. The front hole is not used with the standard bracket.
Owner´s Manual Permolock C Installation Installation of manual release lever in a vehicle Read through the instructions before starting installation. The manual release lever must be installed so that the user can easily operate it when necessary. The lever is intended for cases where the vehicle electrical system is not functioning optimally.
Page 29
Owner´s Manual Permolock C Installation = Position of the stop screws Correct installation Direction of travel Prohibited installation Installation of release lever.
Owner´s Manual Permolock C Installation Installation of quick anchoring set Order no:1820549 List of parts that should be in the set 1. 4 pcs. Lock nuts M10 fzb 5. 1 pc. Tool clamp 2. 4 pcs. Washer BRB 10.5x20x2 fzb 6.
Page 31
Owner´s Manual Permolock C Installation 1. Check that the cc distance between FORWARDS the keyholes is L= 350 mm. and B= 368 mm. Mark the hole configu- ration of the plates on the vehicle floor, see photo. WARNING The locking plate must always be installed with 368 mm.
Page 32
Owner´s Manual Permolock C Installation 6. Screw the keyhole bolts in place in the hole configuration that best suits the user (choice of 4). Use the supplied 10.5x20x2 shim and locknut M10. CAUTION It is important that the lock plate be fitted in a straight line in relation to the wheelchair wheels.
Permolock together with suggested rem- edies. Note that this guide cannot describe all the problems and events which could occur and you should always contact your service contact or Permobil in case of doubt.
Page 43
Owner´s Manual Permolock C Troubleshooting Troubleshooting guide EVENT POSSIBLE CAUSE REMEDY You have forgotten to press Reverse the wheelchair off the The wheelchair is not the locking device control locking plate. Press the locking locked in position in button before moving the device control button so the Permolock.
Permits use of original car seat in Permolock C. Order no:1820550 Quick anchoring set Used to anchor the Permolock C in a vehicle and permits easy transfer of the lock between different positions in the vehicle. The set also includes two installa- tion spacers for installing of the quick anchoring set on a sloping surface.