Table of Contents
Advertisement
Quick Links
Installation Instructions
Passport 1000 PG
Mortise Lock
WARNING
This product can expose you to
lead which is known to the state of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65warnings.ca.gov.
1-800-727-5477 • www.sargentlock.com
Copyright © 2012, 2022 SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express
written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
WARNING
Attention Installer: Improper
installation may result in dam-
age to the product and void the
factory warranty.
A7807D 12/22
Advertisement
Table of Contents
Related Manuals for Assa Abloy Sargent Passport 1000 PG
Summary of Contents for Assa Abloy Sargent Passport 1000 PG
- Page 1 Installation Instructions Passport 1000 PG Mortise Lock WARNING WARNING This product can expose you to Attention Installer: Improper lead which is known to the state of installation may result in dam- California to cause cancer and birth age to the product and void the defects or other reproductive harm.
-
Page 2: Table Of Contents
Passport 1000 PG Mortise Lock Warning ......................3 General Description . -
Page 3: Warning
(2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. General Description Designed specifi cally for the campus market, the SARGENT Passport 1000 PG Mortise Lock (powered by PERSONA) provides offl ine card/PIN access control, as well as detailed audit capabilities. •... -
Page 4: Hardware Specifi Cations
Passport 1000 PG Mortise Lock Hardware Specifi cations • Stand alone, battery-operated • Complete lockset with on-board memory • Available with or without keypad (magstripe only) • ADA compliant • Easily retrofi ts existing PERSONA door preps (mortise) • Latch - Stainless steel •... -
Page 5: Parts Breakdown
Passport 1000 PG Mortise Lock Parts Breakdown PG Standalone With Card Insert and/or Keypad ITEM PART NO. DESCRIPTION 52-0757 Lens (Cliplite) 52-0736 Outside Passport Escutcheon (With Keypad) 52-0737 Outside Passport Escutcheon (Without Keypad) 52-3593 Slim Style Keypad Assembly (KP-PG Only) 52-0760 Light Pipe (Cliplite) 01-9299... - Page 6 Passport 1000 PG Mortise Lock Parts Breakdown 8200 Series Mortise Lock ITEM PART NO. DESCRIPTION See catalog Cylinder & Key Assembly 13-0140 Compression Spring See catalog Blocking Ring See catalog Cylinder Rosette See catalog Mortise Lock body 77-2591 Tab Turn Lever Assembly See catalog Inside Lever Handle See catalog...
-
Page 7: Installation Instructions - Door Preparation
Passport 1000 PG Mortise Lock Installation Instructions - Door Preparation Verify Hand and Bevel of Door Stand on outside/locked side of door when determining the door hand. LHRB RHRB Left Hand Left Hand Right Hand Right Hand Hinges Left Reverse Bevel Hinges Right Reverse Bevel Open Inward... -
Page 8: Installation Instructions - Change Hand Of Lock Body
Passport 1000 PG Mortise Lock Installation Instructions - Door Preparation Prepare Lock Body NOTE: Lock body is shipped with a removable perforated sticker covering the retaining ring on the non-cylinder side (inside of door) of the lock body. Perforated Cables and connectors are coiled inside the retaining ring. Sticker •... - Page 9 Passport 1000 PG Mortise Lock Installation Instructions - Change Hand of Lock Body, continued Reverse Lock Hand Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Figure 7B): 1. Position lock body with red surface of locking piece visible. 2.
-
Page 10: Installation Instructions - Installation Of Lock Body
Passport 1000 PG Mortise Lock Installation Instructions - Installation of Lock Body 1. Insert lock body into mortised cutout (Figure 8). 2. Connector and wires must be coiled within retaining ring in cylinder hole. 3. Push cable and connector through perforated sticker* on non-cylinder side of hole. -
Page 11: Installation Instructions - Installation Of Cylinder
Passport 1000 PG Mortise Lock Installation Instructions - Installation of Cylinder Note: For proper cylinder/parts orientation see Figure 10A. Slide cylinder through the spring and rosette/ collar and screw into lockbody, rotating the cylinder clockwise. Cylinder should be fl ush with rosette/collar. Note: SARGENT logo must be horizontal and on the Rosette must be oriented as... -
Page 12: Installation Instructions - Gasket Installation (Optional)
Passport 1000 PG Mortise Lock Installation Instructions - Gasket Installation (Optional) Note: Optional, for non-fi re rated doors only. For non-fi re rated door applications, an optional gasket (Figure 12) may be used as a weather seal between the escutcheon and the outside door surface. Peel off adhesive backing and attach to (outside) escutcheon... -
Page 13: Installation Instructions - Installation Of Inside Component Assembly
Passport 1000 PG Mortise Lock Installation Instructions - Installation of Outside Escutcheon and Mounting Plate Assembly, continued Cable from lock body feeds thru bottom (Figure 13A and 13B). 3. Attach grounding lug to bottom right screw and note upright positioning of lug as shown (Figure 13B). 4. -
Page 14: Installation Instructions - Installation Of Connectors
Passport 1000 PG Mortise Lock Installation Instructions - Installation of Connectors Secure the following connectors onto the circuit board (Figure 15 and Detail): Note: Connectors go on only From outside trim one way. Do not force and do (ground) not offset connectors. Be sure they are completely seated (fl... -
Page 15: Installation Instructions - Installation Of Inside Escutcheon
Passport 1000 PG Mortise Lock Installation Instructions - Installation of Inside Escutcheon 1. Position inside escutcheon. 2. Insert screws, top and bottom, and tighten securely. DO NOT OVERTIGHTEN. Note: All wires should be placed inside to avoid being pinched. 3. Straighten escutcheon and tighten securely. Installation Instructions - Application of Front Plate Attach front plate with (2) #8-32 X 1/4"... -
Page 16: Setting Up The Locklink™ And Contact Card For First Use
Passport 1000 PG Mortise Lock Setting up the LockLink™ and Contact Card for First Use* *NOTE: The following steps in this section are only performed one time. Once Bluetooth pairing is complete, these steps do not need to be repeated to program locks (Section 8 ”Lockset Programming”) Pairing the Pocket PC with the Contact Card 1. -
Page 17: Lockset Programming
Passport 1000 PG Mortise Lock Setting up the LockLink™ and Contact Card for First Use, continued Confi guring the LockLink™ Software 1. When the list entry appears, highlight it and tap ‘Next’. 2. Enter “1234” when prompted for ‘Passcode.’ 3. Tap the ‘COM Ports’ tab at the bottom of the screen. - Page 18 Passport 1000 PG Mortise Lock LockSet Programming, continued Start the PERSONA LockLink™ Software 1. Tap on the Pocket PC Screen. 2. If visible, select PERSONA LockLink™ to launch the program; otherwise, tap Start and Programs to launch the Programs list and then select the PERSONA LockLink™...
- Page 19 Passport 1000 PG Mortise Lock LockSet Programming, continued Upload Full Program, continued 4. Follow the directions on the screen. NOTE: You will be prompted to insert the Contact Card into the lock three times. 5. When the data has fi nished loading, you are notifi ed to remove the Contact Card from the lock. 6.
- Page 20 Passport 1000 PG Mortise Lock LockSet Programming, continued Upload Full Program, continued 7. Program initializes and directs you to remove the Contact Card. 8. Follow the on-screen directions and reinsert the Contact Card a third time. 9. Remove the Contact Card. 10.
- Page 21 Passport 1000 PG Mortise Lock LockSet Programming, continued Upload Full Program, continued 11. After programming the new lockset, verify operation by performing the Operational Check (refer to Section 22). 12. Repeat this procedure for each lock to be programmed with lock data. NOTE: With a successful upload, the time and date that the lock was programmed will appear beside each lock name.
-
Page 22: Operational Check
Passport 1000 PG Mortise Lock Operational Check IMPORTANT: Be sure to test functions prior to closing door. In all cases, perform the following checks: 1. Ensure that inside lever retracts latch (and deadbolt for deadbolt functions). • For devices with cylinders, the following checks apply: Insert key into cylinder and rotate: a. - Page 23 Passport 1000 PG Mortise Lock A7807D 12/22 1-800-727-5477 • www.sargentlock.com Copyright © 2012, 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
- Page 24 A7807D 12/22...