Advertisement
Quick Links
Advertisement
Related Manuals for Assa Abloy PASSPORT 1000
Summary of Contents for Assa Abloy PASSPORT 1000
- Page 1 PASSPORT 1000 Mortise Lock Installation Instructions A8011H Copyright 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
-
Page 3: Table Of Contents
(2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée. SARGENT Mfg. Co. Passport 1000 locksets utilizing a door position switch (DPS) are not rated for, or intended for use in life safety applications. -
Page 4: General Description
Passport 1000 P2 Mortise Lock General Description An ANSI/BHMA Grade 1 lock using WiFi technology, the Passport 1000 P2 Mortise lock provides a cost-effective, future-proof solution for campuses. Featuring multiCLASS SE Technology from HID Global , it provides simultaneous support for multiple ®... -
Page 5: Parts Breakdown
Passport 1000 P2 Mortise Lock Parts Breakdown P2 WiFi Lock with Magnetic Card Swipe With or Without Keypad ITEM No. PART No. DESCRIPTION 52-3583-[finish] Outside Escutcheon Assemby, mag stripe 52-3582-[finish] Outside Escutcheon Assemby, mag stripe and Keypad (shown) 52-4244-[finish] Outside Escutcheon Assemby, Mag Swipe, Keypad, and HID 125 kHz Prox... -
Page 6: Tools Required
Passport 1000 P2 Mortise Lock Parts Breakdown (Continued) Tools Required: • #2 Phillips screwdriver • Flat head • T20 Torx driver ® • Security allen wrench ITEM PART No. DESCRIPTION See catalog #41 Cylinder (1-1/8" Minimum Length) Consult Factory Cylinder Rosette P1-82276-[finish]* Lock body with deadbolt &... -
Page 7: Installation Instructions
Passport 1000 P2 Mortise Lock Installation Instructions 1 Door Preparation A. Verify Hand and Bevel of Door Stand on outside of locked door when determining door hand. Left Hand Left Hand Right Hand Right Hand Hinges Left. Reverse Bevel Hinges Right. - Page 8 Passport 1000 P2 Mortise Lock 2 Prepare Lock Body 1. Reverse Lock Hand Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A): a. Position lock body with red surface Right Hand of locking piece visible.
- Page 9 Passport 1000 P2 Mortise Lock 3 Install Lock Body Note: Do not pull the lock into the pocket using the harness alone. Ensure that the wire harness is not pinched between the lock and the mortise pocket. 1. Feed the wire harness into the mortise pocket and through inside preparation hole as depicted in Figure 3.
- Page 10 Passport 1000 P2 Mortise Lock 4 Outside Cylinder Installation 1. Slide the spring and the rosette onto the cylinder. 2. Rotate the cylinder into cylinder hole with fingers. 3. Insert key 75% of the way and utilize the key to rotate the cylinder into the rest of the cylinder hole.
- Page 11 Passport 1000 P2 Mortise Lock 5 Assemble Outside Trim 1. With outside lever horizontal, insert the mounting posts through outside of door and lock body. Make certain the lever spindle is properly engaged inside the lock body (Fig 5A). 2. On the inside of the door, insert spindle into square hole of mortise lock (Fig 5B).
- Page 12 Passport 1000 P2 Mortise Lock 6 Install Inside Rose and Inside Lever Assembly 1. Place inside rose flush against door surface and rotate first counter-clockwise to seat the threads, then clockwise to securely tighten. 2. Slide lever onto spindle until fully seated. Be sure handle is horizontal and facing the hinge side of the door.
- Page 13 Passport 1000 P2 Mortise Lock 7 Install Thumb Turn 1. Insert thumb turn into preparation hole and engage slot in lock body. 2. Orient mounting plate so screw hole is vertical (aligned with preparation holes). 3. Secure plate with Phillips screw provided.
- Page 14 Passport 1000 P2 Mortise Lock 9 Mounting Plate Assembly 1. On the inside of the door, position the mounting plate over the indicated holes. Mounting Plate 2. Feed reader harness through central opening on mounting plate (Fig. 9A, B). 3. Route ground ring terminal from lock body through bottom of mounting plate and attach to bottom left corner using (1) #8-32 x 1-7/8”...
- Page 15 Passport 1000 P2 Mortise Lock Installation of Connectors CAUTION - Do not touch or allow debris to enter connector contacts. Secure the following connectors to their respective terminals (Fig. 10): A. Secure the 10-pin lock body assembly connector. IMPORTANT: Do not run wires through bottom hole in plate (Fig. 10) - it will damage wires and the controller connector.
- Page 16 Passport 1000 P2 Mortise Lock 11 Install Inside Module Component Assembly 1. Insert top tabs of controller into slots on mounting plate (Fig. 13). 2. Ensure proper alignment of board-to-board connectors while pivoting bottom of controller toward door until tab on bottom snaps securely into place on mounting plate.
- Page 17 Passport 1000 P2 Mortise Lock 12 Install Batteries Before installing batteries for the first time: Remove pull tab from its position beneath the coin cell by pulling on tab in direction of arrows printed on tab (Fig. 12). a. Place (6) “AA” alkaline batteries in the compartment, being careful to align polarity properly.
- Page 18 Passport 1000 P2 Mortise Lock 14 Attach Outside Front Plate Attach front plate with (2) #8-32 X 1/4” flat head screws (Fig. 14). Inside of Door (2) #8-32 x 1/4” Flat Head Screws Fig. 14 1-800-810-WIRE • www.sargentlock.com • A8011H...
-
Page 19: Operational Check
Passport 1000 P2 Mortise Lock Operational Check IMPORTANT: Be sure to test functions prior to closing door. In all cases, perform the following checks: 1. Ensure that inside lever retracts latch (and deadbolt for deadbolt functions). • For units with cylinders, the following checks apply: Insert key into cylinder and rotate: a. - Page 20 The company’s customer base includes commercial construction, institutional, and industrial markets. Copyright © 2016, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.