Connecting The Gas Cylinder To The Appliance; Leak Testing; Installation - Masport MB Owner's Manual

While using the rotisserie, adjust the counter weight to balance
the food being cooked
CONNECTING THE GAS CYLINDER TO
THE APPLIANCE
This appliance is only suitable for use with low-pressure butane,
propane or their mixture gas and fitted with the appropriate low-
pressure regulator via a flexible hose. The barbecue is set to
operate
28-30 mbar regulator with butane gas @ category I3+
37mbar regulator with propane gas @ category I3+
37 mbar regulator with butane, propane or their mixtures @
category I3B/P(37)
30 mbar and 50mbar regulator with butane, propane or their
mixtures @ category I3B/P(30) or category I3B/P(50) respectively
CAUTION!
Only the gas type and Gas Category listed in the rating label
on the barbecue could be used on your barbecue.
GAS REGULATOR
This BBQ is designed to operate using a 5kg LPG gas bottle and
the pressure regulator should correspond to the pressure and
gas category of the appliance. Your nearest Gas Retailer can
advise of the correct gas pressure. The regulator should comply
with EN16436 Or EN16129 with current version and national
regulation.
For operating this BBQ, use one of the following Regulators (if
you are not sure, please see your nearest gas Retailer),
28-30/37 mbar regulator for I3+
28-30mbar regulator for I3B/P(30)
50 mbar regulator for I3B/P(50)
Always use the gas bottle in the upright position.
The life expectancy of the regulator is estimated as 10 years. It is
recommended that the regulator is changed within 10 years of the
date of manufacture or the national conditions require it.
GAS HOSE
The type of replaceable hose should meet the standard of
EN1763-1-Class 3. The hose used must conform to the relevant
standard for the country of use. The length of the hose must
be 0.7 meters (minimum) and 1.5 meters (maximum). Worn or
damaged hose must be replaced. Ensure that the hose is not
obstructed, kinked, or in contact with any part of the barbecue
other than at its connection. It is recommended that the hose is
changed within 1 year of the date of manufacture or the national
conditions require it.

LEAK TESTING

When to Test: The BBQ gas bottle, regulator & hose assembly
should be checked for leaks, using the soapy water leak test,
every time you reconnect your regulator to the BBQ gas bottle.
50
546001.A.6 - July 17, 2019
You should also test after any long period of non-use, such as at
the beginning of BBQ season.
What to use: You will need a soapy water solution to check for
any leaks. Mixing liquid hand soap with water will work fine (do
not use any other household cleaning products).
How to Test: Put some soapy water in a spray bottle or a
dish. Turn on the gas bottle but do not turn on the BBQ. Next,
spray the entire valve, regulator and hose assembly with the
soapy water including where the hose connects to the BBQ.
Alternatively, you can apply the soapy water with a paint brush,
basting brush.
Bubbles will form if there is a gas leak and you may also smell the
gas. If you find a leak, turn off the gas bottle immediately!
Do not turn back on or attempt to use the BBQ if a gas leak has
been detected, contact your local BBQ Dealer for repair.

INSTALLATION

This barbecue is for outdoor use only and should be placed in
a well-ventilated area. Take care to ensure that the minimum
clearances guidelines are followed.
MINIMUM CLEARANCES:
We strongly recommend minimum clearances from combustible
to be:
• Rear - 450mm
• Sides - 250 mm
• Top - 1000 mm
250mm
Keep this barbecue away from any flammable materials! This
appliance shall only be used in an above ground open-air
situation with natural ventilation, without stagnant areas, where
gas leakage and products of combustion are rapidly dispersed by
wind and natural convection. This barbecue is not designed for
marine use.
ANY ENCLOSURE IN WHICH THE APPLIANCE IS USED
SHALL COMPLY WITH ONE OF THE FOLLOWING:
1. An enclosure with walls on all sides, but at least one
permanent opening at ground level and no overhead cover.
2. Within a partial enclosure that includes an overhead cover and
no more than two walls.
3. Within a partial enclosure that includes an overhead cover and
more than two walls, the following shall apply:
1000mm
450mm
250mm