Table of Contents
Advertisement
INSTALLING BATTERY CHARGER
INSTALLING BATTERY CHARGER
WARNING
WARNING
Install the battery charger in a dry, well-
Install the battery charger in a dry, well-
•
•
ventilated area.
ventilated area.
Do not
Do not
•
•
exposed to water including rain; otherwise
exposed to water including rain; otherwise
there is a danger of causing an electric shock
there is a danger of causing an electric shock
accident or a re.
accident or a re.
When a charging
When a charging
•
•
of hydrogen gas is released from the battery.
of hydrogen gas is released from the battery.
If the gas density increases, there is a danger
If the gas density increases, there is a danger
of an explosion. The battery charger should be
of an explosion. The battery charger should be
installed in a well-ventilated area.
installed in a well-ventilated area.
The input cable should be connected and
The input cable should be connected and
•
•
disconnected by qualified or authorized
disconnected by qualified or authorized
personnel.
personnel.
The input cable
The input cable
•
•
the MCBs are turned off. The ground lead must
the MCBs are turned off. The ground lead must
be grounded.
be grounded.
When carrying the battery charger, hold the bottom of
When carrying the battery charger, hold the bottom of
•
•
the chassis.
the chassis.
The battery charger generates heat during operation.
The battery charger generates heat during operation.
•
•
Make sure that adequate space is provided around
Make sure that adequate space is provided around
the battery charger, more than 10 cm at both sides
the battery charger, more than 10 cm at both sides
and rear side (A) and more than 30 cm above the top
and rear side (A) and more than 30 cm above the top
surface.
surface.
Working conditions:
Working conditions:
•
•
S
S
t
t
o
o
r
r
a
a
g
g
e
e
t
t
e
e
O
O
p
p
e
e
r
r
a
a
t
t
i
i
n
n
g
g
t
t
e
e
Humidity range
Humidity range
The battery charger should be provided separately
The battery charger should be provided separately
•
•
with a 3-phase, 200V AC ground-fault circuit breaker
with a 3-phase, 200V AC ground-fault circuit breaker
(MCB) at the input side.
(MCB) at the input side.
Selecting and switching over input taps:
Selecting and switching over input taps:
•
•
It is
It is
necessary to
necessary to
transformer according to the AC input voltage for
transformer according to the AC input voltage for
charging.
charging.
STA
STATIONARY
install the battery charger in a
install the battery charger in a
process reaches its end,
process reaches its end,
should be connected
should be connected
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
-
-
2
2
0
0
m
m
p
p
e
e
r
r
a
a
t
t
u
u
r
r
e
e
0
0
30% to 95% (No condensation of
30% to 95% (No condensation of
moisture allowed)
moisture allowed)
switch
switch
over the
over the
https://www.forkliftpdfmanuals.com/
TIONARY
BATTERY CHARGER
BATTERY CHARGER
place
place
a lot
a lot
after all
after all
°
°
C
C
t
t
o
o
6
6
0
0
°
°
C
C
°
°
C
C
t
t
o
o
4
4
0
0
°
°
C
C
taps of
taps of
the charging
the charging
3-19
3-19
Hide quick links:
Advertisement
Chapters
Table of Contents
