Load Handling; Pick-Up; Stacking Stacking - UniCarriers FRSB14-8 Operation & Maintenance Manual

PICK-UP

PICK-UP
1) The fork spread should be as wide as possible 1) The fork spread should be as wide as possible
to maintain the balance of the load. to maintain the balance of the load.
2) Place the truck right in front of the load to be 2) Place the truck right in front of the load to be
handled. handled.
3) 3) The pallet should be positioned parall The pallet should be positioned
forks. forks.
4) 4) Insert the forks as far as Insert the forks as far as
Raise the load 5 to 10 cm off the upper surface of Raise the load 5 to 10 cm off the upper surface of
5) 5)
the outriggers. To raise the load from the ground: the outriggers. To raise the load from the ground:
First First lift lift the forks the forks
oor surface, and make sure the load is properly oor surface, and make sure the load is properly
positioned across both forks. positioned across both forks.
6) If you find the load on the forks is off center, 6) If you find the load on the forks is off center,
raise the load to a height of 5 to 10 cm above raise the load to a height of 5 to 10 cm above
the outriggers and side-shift the forks properly the outriggers and side-shift the forks properly
to align the load's center of gravity with the to align the load's center of gravity with the
centerline of the truck. centerline of the truck.
WARNING WARNING
When handling loads with the side-shifter, When handling loads with the side-shifter,
follow these precautions; otherwise there is follow these precautions; otherwise there is
a danger of tipping the truck over to the side a danger of tipping the truck over to the side
because of losing lateral balance. because of losing lateral balance.
Do not Do not t travel with an off- ravel with an
• •
forks. Never lift an uneven load. forks. Never lift an uneven load.
Do not Do not o operate the side-shifter perate the side-shifter
• •
a load. a load.
Do not Do not operate the side-shifte operate the side-shifte
• •
forks raised quite high (150 cm or higher), forks raised quite high (150 cm or higher),
except when the load can be stabilized, as except when the load can be stabilized, as
it is over a shelf. it is over a shelf.
Do not operate the side-shifter while Do not operate the side-shifter while
• •
traveling. Do not jerk traveling. Do not jerk
CAUTION CAUTION
A A sid side-s e-shif hiftin ting g
with the forks raised 5 to 10 cm above the top with the forks raised 5 to 10 cm above the top
surface of the outriggers. surface of the outriggers.
Do not try to side-shift the load with the bottoms of Do not try to side-shift the load with the bottoms of
the forks in contact with the ground or oor surface; the forks in contact with the ground or oor surface;
otherwise the side-shifter might be otherwise the side-shifter might be
7) Tilt back the forks fully and retract the mast 7) Tilt back the forks fully and retract the mast
completely. Start completely . Start
8) When handling a bulky load that restricts your 8) When handling a bulky load that restricts your
vision, drive the truck forward. vision, drive the truck forward.
parallel with both el with both
possible into the pallet. possible into the pallet.
5 5 to to 10 10 cm cm off off the ground the ground
off-center load on t center load on
while lifting while lifting
r with r with
the side-shifter. the side-shifter.
operat ope ration ion sho should uld be be perfor per
damaged. damaged.
traveling. traveling.
https://www.forkliftpdfmanuals.com/

LOAD HANDLING

LOAD HANDLING
STACKING STACKING
WARNING WARNING
Never tilt the mast Never tilt the mast
• •
raised except when the forks are over the raised except when the forks are over the
rack or a stack. rack or a stack.
Do not Do not
• •
1) 1) When When approaching approaching
your truck. your truck.
2) 2) Stop the Stop the
or or
is to be deposited. is to be deposited.
3) 3) Conrm Conrm
4) 4) Tilt Tilt the forks the forks
the load is not correctly positioned for stacking, the load is not correctly positioned for stacking,
carefully operate the side-shift lever to position carefully operate the side-shift lever to position
the load correctly. Raise the load until the the load correctly. Raise the load until the
bottom of the load is a little higher than the bottom of the load is a little higher than the
position where you want to place it. position where you want to place it.
5) 5) Move forward Move forward
front of the correct position, and stop the truck. front of the correct position, and stop the truck.
6) 6) Using the Using the
place the load over the correct position. place the load over the correct position.
7) 7) Make sure Make sure
the he
Slowly lower the load into position. Make sure Slowly lower the load into position. Make sure
the load is securely placed or stacked. the load is securely placed or stacked.
* * If the pallet or If the pallet or
use the following procedure: use the following procedure:
the the
Pull about Pull about
retracting the forks and raise the forks 5 to retracting the forks and raise the forks 5 to
10 10 cm. cm.
deposit position and slowly lower the load deposit position and slowly lower the load
into position. into position.
8) 8) Fully retract Fully retract
the pallet or load with forks. Make sure there the pallet or load with forks. Make sure there
is no one or obstacle in front of the truck and is no one or obstacle in front of the truck and
formed med
move forward. move forward.
9) 9) After making After making
or load, lower the forks to the basic traveling or load, lower the forks to the basic traveling
position (30 cm off the ground or oor surface). position (30 cm off the ground or oor surface).
10) Tilt back the forks. 10) Tilt back the forks.
3-8 3-8
forward with the forward with the
leave the truck leave the truck with the load with the load
the the deposit deposit area, area,
truck before truck before the area the area where where y
the the safety safety of of the the deposit deposit
forward until forward until they are they are
slowly to slowly to place the place the
reach lever, reach lever, advance the mast advance the mast
the load the load is j is just above ust above
load is not load is not placed prope placed
1/4 of 1/4 of the forks the forks
Advan Advan ce ce the forks the forks
the mast the mast using caution using caution
sure the sure the fork tips fork tips
load load
raised. raised.
slow slow down down
your load our load
position. position.
horizontal. If horizontal. If
truck just truck just in in
to to
the right the right place. place.
properly, rly,
off off the load the load by by
to to the correct the correct
not to not to hit hit
leave the leave the pallet pallet