Table Of Contents - Trane Symbio 800 Control Upgrade Kit Installation Instructions Manual

Table of Contents

Other Required Manuals
Required Tools
. . . . . . . . . . . . . . . . . . . . . . . . 3
Field-Provided Material
General Information
About This Manual
Unit Model Number
Model Number Descriptions
Getting Started
. . . . . . . . . . . . . . . . . . . . . . . . . . 7
Nameplate
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Symbio 800 AdaptiView Display Upgrade Kit
Contents
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Running the IPC Bus . . . . . . . . . . . . . . . . . 8
Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Check the Configuration and Set-Points in the
DynaView Display . . . . . . . . . . . . . . . . . . 10
Save the DynaView Configuration and Set-
Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Remove the Existing Control Panel Door
Install New Control Panel Door and Symbio
800 Controller
. . . . . . . . . . . . . . . . . . . . . . . . 11
Choosing Display Arm Mounting Location
Alternative mounting location: . . . . . . . . 13
Mounting Display Arm
Adjusting the Tracer AdaptiView Display Arm
14
Install Power Supplies and Hardware
Install 1A2 Power Supply-CH530 If Not Al-
ready Present . . . . . . . . . . . . . . . . . . . . . . 15
Install 1A2 Power Supply - CH531 Prebuilt
Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Install Quad Relay Output LLID-CH530 If Us-
ing Chiller Control Sequence 1 . . . . . . . . 16
Install Communication Cable Between 1A1
and 1A2 Power Supplies . . . . . . . . . . . . . 16
Connect Input Power Wiring to 1A2 Power
Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Routing New Wire Into and Out of the Control
Panel Enclosure . . . . . . . . . . . . . . . . . . . . 17
Wiring Connections to the Display and Sym-
bio 800 Controller . . . . . . . . . . . . . . . . . . . 17
Solid State Oil Heater Relay Installation
Mounting Location . . . . . . . . . . . . . . . . . . 20
4
. . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . 6
. 11
. . . . . . . . . . . . . . . . 13
. . . 15
. 20
Installation . . . . . . . . . . . . . . . . . . . . . . . . .21
Install Options
LON Option Installation . . . . . . . . . . . . . . .22
Communication Option . . . . . . . . . . . . . . .22
Communication Device Mounting . . . . . .23
Water Flow Measurement Options . . . . . .24
Energy Meter Option Installation . . . . . . .25
Expansion Module Option . . . . . . . . . . . . .26
Before Restoring System Power . . . . . . . .27
Restoring System Power . . . . . . . . . . . . . .27
Programming
Programming the Symbio 800 AdaptiView
Start-Up
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Wiring Diagrams
12
. . . . . . . . . . . . . . . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . . . . . . .28
. . . . . . . . . . . . . . . . . . . . . . . .32
CDUB-SVN001B-EN
28