Names And Functions Of The Interface Board (Optional) - Panasonic PT-RQ13K Operating Instructions Manual

Names and functions of the Interface Board (optional)

This projector is equipped with two SLOT NX-specification slots.
There are four SDI input terminals and one DIGITAL LINK input terminal equipped on this projector as the
standard video input terminals. The input for HDMI, DVI-D, and SDI can be added by installing the optional
Interface Board in the slot.
The terminal name of the optional Interface Board is described with different terminal name in this document when
it is installed in <SLOT 1> and when it is installed in <SLOT 2>. Refer to following information for details.
r Interface Board for HDMI 2 input (Model No.: ET-MDNHM10)
This board supports the HDMI signal.
1 <HDMI IN 1> terminal (when installed in <SLOT 1>), <HDMI
IN 3> terminal (when installed in <SLOT 2>)
This is a terminal to input the HDMI signal.
r Interface Board for DVI-D 2 input (Model No.: ET-MDNDV10)
This board supports the DVI-D signal.
1 <DVI-D IN 1> terminal (when installed in <SLOT 1>), <DVI-D
IN 3> terminal (when installed in <SLOT 2>)
This is a terminal to input the DVI-D signal.
r 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G)
This board supports the SD-SDI signal, HD-SDI signal, and 3G-SDI signal.
1 <3G-SDI 2 OUT> terminal (when installed in <SLOT 1>),
<3G-SDI 4 OUT> terminal (when installed in <SLOT 2>)
This is an active through terminal to output the SDI signal input
to the <3G-SDI 2 IN> terminal/<3G-SDI 4 IN> terminal of this
board.
2 <3G-SDI 2 IN> terminal (when installed in <SLOT 1>),
<3G-SDI 4 IN> terminal (when installed in <SLOT 2>)
This is a terminal to input the SDI signal.
Note
f This projector does not support audio output because it is not equipped with audio function. However, when SDI signal with audio is input to
the <3G-SDI 1 IN>/<3G-SDI 2 IN>/<3G-SDI 3 IN>/<3G-SDI 4 IN> terminal, a signal with audio is output from the <3G-SDI 1 OUT>/<3G-SDI
2 OUT>/<3G-SDI 3 OUT>/<3G-SDI 4 OUT> terminal.
f To use the 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G), it is necessary for the firmware version of the 3G-SDI Terminal
Board with Audio to be 2.00 or later. Confirm the firmware version of the 3G-SDI Terminal Board with Audio when it does not operate after
installing to the projector.
Consult your dealer regarding the version update to the latest firmware if the version is earlier than 2.00.
For details on how to confirm the firmware version, refer to "How to confirm the firmware version of the 3G-SDI Terminal Board with Audio"
(x page 31).
30 - ENGLISH
Chapter 1 Preparation — About your projector
3 1
3 1
1 2
2 3
2 <HDMI IN 2> terminal (when installed in <SLOT 1>), <HDMI
IN 4> terminal (when installed in <SLOT 2>)
This is a terminal to input the HDMI signal.
3 Handle
2 3
2 <DVI-D IN 2> terminal (when installed in <SLOT 1>), <DVI-D
IN 4> terminal (when installed in <SLOT 2>)
This is a terminal to input the DVI-D signal.
3 Handle
3 4 5
3 <3G-SDI 1 OUT> terminal (when installed in <SLOT 1>),
<3G-SDI 3 OUT> terminal (when installed in <SLOT 2>)
This is an active through terminal to output the SDI signal input
to the <3G-SDI 1 IN> terminal/<3G-SDI 3 IN> terminal of this
board.
4 <3G-SDI 1 IN> terminal (when installed in <SLOT 1>),
<3G-SDI 3 IN> terminal (when installed in <SLOT 2>)
This is a terminal to input the SDI signal.
5 Handle