Panasonic PT-RQ13K Operating Instructions Manual page 57

Chapter 3 Basic Operations — Switching on/off the projector
Initial setting (operation setting)
Set the items for the operating method depending on the projector's application and duration of usage.
After completed the initial setting, you can change the settings of each item from the [PROJECTOR SETUP]
menu. If you change the settings while using the projector, the duration until the luminance of light source
decreases by half may shorten or the luminance may decrease.
By using this initial setting (operation setting), you can complete the settings at once when installing the projector,
if the operation method of the projector is determined in advance. If [ALL USER DATA] is executed from the
[PROJECTOR SETUP] menu → [INITIALIZE], do not change the initial setting (operation setting) and proceed to
next initial setting (installation setting) by pressing the <ENTER> button. If you need to change the setting, ask the
person responsible for this projector (such as a person in charge of equipment or operation).
Note
f The preceding initial setting screen is displayed when the projector is switched on for the first time after purchase. If [ALL USER DATA] is
executed from the [PROJECTOR SETUP] → [INITIALIZE], the settings before execution are displayed in [OPERATING MODE] and [MAX
LIGHT OUTPUT LEVEL].
f For the relationship between the luminance and the runtime, refer to "Interrelation of luminance and runtime" (x page 59).
f For details on each setting item, refer to the [PROJECTOR SETUP] menu → [OPERATION SETTING].
1) Press as to select [OPERATING MODE].
2) Press qw to switch the item.
f The items will switch each time you press the button.
f Set [OPERATING MODE] to anything other than [ECO], [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3]
when using the projector at an altitude of 2 700 m (8 858') or higher above sea level.
[NORMAL]
*1
[ECO]
*1
[LONG LIFE1]
*1
[LONG LIFE2]
*1
[LONG LIFE3]
*1
[USER1]
[USER2]
[USER3]
*1 The runtime is estimated when the [PICTURE] menu → [DYNAMIC CONTRAST] is set to [3].
f When [NORMAL], [ECO], [LONG LIFE1], [LONG LIFE2], or [LONG LIFE3] is selected, proceed to Step 5).
3) Press as to select [MAX LIGHT OUTPUT LEVEL].
4) Press qw to adjust.
Operation
Press w.
Press q.
5) Press as to select [LIGHT OUTPUT].
INITIAL SETTING
OPERATING MODE
MAX LIGHT OUTPUT LEVEL
LIGHT OUTPUT
BRIGHTNESS CONTROL SETUP
CONSTANT MODE
LINK
CALIBRATION TIME
CALIBRATION MESSAGE
Set the way to use the projector. For details, please
refer to the operating instructions "When the initial
setting screen is displayed".
MENU SELECT
SET
ENTER
Set this item when high luminance is required. The estimated runtime is approximately 20 000 hours.
Set this item to increase the life of the light source though it will lower the luminance than [NORMAL].
The estimated runtime is approximately 24 000 hours.
Set this item to increase the life of the light source though it will lower the luminance than [ECO]. The
estimated runtime is approximately 43 000 hours.
Set this item to increase the life of the light source though it will lower the luminance than [LONG
LIFE1]. The estimated runtime is approximately 61 000 hours.
Set this item to increase the life of the light source though it will lower the luminance than [LONG
LIFE2]. The estimated runtime is approximately 87 000 hours.
Set [MAX LIGHT OUTPUT LEVEL] and [LIGHT OUTPUT] individually.
Adjustment
Increases the maximum level of brightness correction.
Decreases the maximum level of brightness correction.
2/7
NORMAL
100%
100%
OFF
GROUP A
OFF
ON
CHANGE
Range of adjustment
8.0 % - 100.0 %
ENGLISH - 57