Table of Contents
Advertisement
Names and functions of the Interface Board (optional)
This projector is equipped with two SLOT NX-specification slots.
There are four SDI input terminals and one DIGITAL LINK input terminal equipped on this projector as the
standard video input terminals. The input for HDMI, DVI-D, and SDI can be added by installing the optional
Interface Board in the slot.
The terminal name of the optional Interface Board is described with different terminal name in this document when
it is installed in <SLOT 1> and when it is installed in <SLOT 2>. Refer to following information for details.
r Interface Board for HDMI 2 input (Model No.: ET-MDNHM10)
This board supports the HDMI signal.
1
<HDMI IN 1> terminal (when installed in <SLOT 1>), <HDMI
IN 3> terminal (when installed in <SLOT 2>)
This is a terminal to input HDMI signal.
Note
f When performing the simultaneous input of the 4K image (resolution of 3 840 x 2 160 or 4 096 x 2 160) using the Interface Board for HDMI
2 input (Model No.: ET-MDNHM10), it is necessary for the firmware version of the Interface Board for HDMI 2 input to be 2.00 or later. If the
version is earlier than 2.00, the simultaneous process is not performed even if corresponding signal is input. Consult your dealer regarding
the version update to the latest firmware.
For details on how to confirm the firmware version, refer to "How to confirm the firmware version of the Interface Board (optional)"
(x page 35).
r Interface Board for DVI-D 2 input (Model No.: ET-MDNDV10)
This board supports the DVI-D signal.
1
<DVI-D IN 1> terminal (when installed in <SLOT 1>), <DVI-D
IN 3> terminal (when installed in <SLOT 2>)
This is a terminal to input DVI-D signal.
r 3G-SDI Terminal Board with Audio (Model No.: TY-TBN03G)
This board supports the SD-SDI signal, HD-SDI signal, and 3G-SDI signal.
1
<3G-SDI 2 OUT> terminal (when installed in <SLOT 1>),
<3G-SDI 4 OUT> terminal (when installed in <SLOT 2>)
This is an active through terminal to output the SDI signal input
to the <3G-SDI 2 IN> terminal/<3G-SDI 4 IN> terminal of this
board.
2
<3G-SDI 2 IN> terminal (when installed in <SLOT 1>),
<3G-SDI 4 IN> terminal (when installed in <SLOT 2>)
This is a terminal to input SDI signal.
Chapter 1 Preparation — About your projector
3
1
3
1
1
2
2
3
2
<HDMI IN 2> terminal (when installed in <SLOT 1>), <HDMI
IN 4> terminal (when installed in <SLOT 2>)
This is a terminal to input HDMI signal.
3
Handle
2
3
2
<DVI-D IN 2> terminal (when installed in <SLOT 1>), <DVI-D
IN 4> terminal (when installed in <SLOT 2>)
This is a terminal to input DVI-D signal.
3
Handle
3
4
5
3
<3G-SDI 1 OUT> terminal (when installed in <SLOT 1>),
<3G-SDI 3 OUT> terminal (when installed in <SLOT 2>)
This is an active through terminal to output the SDI signal input
to the <3G-SDI 1 IN> terminal/<3G-SDI 3 IN> terminal of this
board.
4
<3G-SDI 1 IN> terminal (when installed in <SLOT 1>),
<3G-SDI 3 IN> terminal (when installed in <SLOT 2>)
This is a terminal to input SDI signal.
5
Handle
ENGLISH - 33
Advertisement
Chapters
Table of Contents
