IEI Technology gKINO-R1000 User Manual
  1. Manuals
  2. Brands
  3. IEI Technology Manuals
  4. Single board computers
  5. gKINO-R1000 Series
  6. User manual

IEI Technology gKINO-R1000 User Manual

Mini-itx sbc
Hide thumbs Also See for gKINO-R1000:
Table of Contents

Advertisement

Quick Links

Download this manual
gKINO-V/R1000 SBC
MODEL:
MODEL:
gKINO-V/R1000
gKINO-V/R1000
Mini-ITX SBC supports AMD® Ryzen™ Embedded V1000/R1000
Series Onboard SoC, DDR4, Triple/Quadruple DP, Dual GbE, M.2,
SATA 6Gb/s, USB 3.2 Gen 1, COM, TPM 2.0, HD Audio and RoHS
Rev. 1.00 - September 1, 2020
gKINO-V/R1000 CPU Card
User Manual
Page I

Advertisement

Table of Contents
loading

Related Manuals for IEI Technology gKINO-R1000

Summary of Contents for IEI Technology gKINO-R1000

  • Page 1 gKINO-V/R1000 SBC gKINO-V/R1000 CPU Card MODEL: MODEL: gKINO-V/R1000 gKINO-V/R1000 Mini-ITX SBC supports AMD® Ryzen™ Embedded V1000/R1000 Series Onboard SoC, DDR4, Triple/Quadruple DP, Dual GbE, M.2, SATA 6Gb/s, USB 3.2 Gen 1, COM, TPM 2.0, HD Audio and RoHS User Manual Page I Rev.
  • Page 2 gKINO-V/R1000 SBC Revision Date Version Changes September 1, 2020 1.00 Initial release Page II...
  • Page 3 gKINO-V/R1000 SBC Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
  • Page 4 gKINO-V/R1000 SBC Manual Conventions WARNING Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. CAUTION Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product. NOTE These messages inform the reader of essential but non-critical information.

  • Page 5: Table Of Contents

    gKINO-V/R1000 SBC Table of Contents 1 INTRODUCTION ......................1 1.1 I ......................2 NTRODUCTION 1.2 M ....................3 ODEL ARIATIONS 1.3 F ........................3 EATURES 1.4 C ......................4 ONNECTORS 1.5 D ....................... 5 IMENSIONS 1.6 D ........................ 7 1.7 T ..................
  • Page 6 gKINO-V/R1000 SBC 3.2.11 I C Connector ....................29 3.2.12 LAN LED Connectors ..................30 3.2.13 M.2 Slot ......................31 3.2.14 PCIe x16 Slot ....................33 3.2.15 RS-232 Serial Port Connectors (COM3 ~ COM6) ........33 3.2.16 SATA 6Gb/s Drive Connector ................ 35 3.2.17 SATA Power Connector ..................
  • Page 7 gKINO-V/R1000 SBC 5 BIOS ..........................61 5.1 I ......................62 NTRODUCTION 5.1.1 Starting Setup ....................62 5.1.2 Using Setup ...................... 62 5.1.3 Getting Help ..................... 63 5.1.4 Unable to Reboot after Configuration Changes ..........63 5.1.5 BIOS Menu Bar ....................63 5.2 M ........................
  • Page 8 gKINO-V/R1000 SBC 5.6 B ........................90 5.7 S & E ......................92 A REGULATORY COMPLIANCE ................94 B PRODUCT DISPOSAL ....................96 C BIOS MENU OPTIONS ..................... 98 D DIGITAL I/O INTERFACE ..................101 E WATCHDOG TIMER ....................104 F ERROR BEEP CODE ....................107 F.1 PEI B ....................
  • Page 9 Figure 1-1: gKINO-V/R1000 ......................2 Figure 1-2: Connectors ........................4 Figure 1-3: gKINO-V1000 Dimensions (mm) ................5 Figure 1-4: gKINO-R1000 Dimensions (mm) ................6 Figure 1-5: Data Flow Diagram ...................... 7 Figure 3-1: Connector and Jumper Locations ................16 Figure 3-2: DC-IN Power Connector Location ................19 Figure 3-3: Audio Connector Location ..................20...
  • Page 10 gKINO-V/R1000 SBC Figure 3-27: DisplayPort Connector Pinout Locations .............45 Figure 3-28: Ethernet Connector ....................46 Figure 3-29: Ethernet Connector ....................47 Figure 3-30: Power Connector ....................48 Figure 3-31: Serial Port Pinouts ....................49 Figure 4-1: SO-DIMM Installation ....................53 Figure 4-2: Removing the M.2 Module Retention Screw ............54 Figure 4-3: Inserting the M.2 Module into the Slot at an Angle..........54 Figure 4-4: Securing the M.2 Module ..................55 Figure 4-5: AT/ATX Mode Select Switch Location ..............56...
  • Page 11 gKINO-V/R1000 SBC List of Tables Table 1-1: Model Variations ......................3 Table 1-2: Technical Specifications ....................10 Table 3-1: Peripheral Interface Connectors ................18 Table 3-2: Rear Panel Connectors ....................18 Table 3-3: DC-IN Power Connector Pinouts ................19 Table 3-4: Audio Connector Pinouts ..................20 Table 3-5: Audio Amplifier Connector Pinouts (SPK_L1) ............21 Table 3-6: Audio Amplifier Connector Pinouts (SPK_R1) ............21 Table 3-7: Battery Connector Pinouts ..................23...
  • Page 12 gKINO-V/R1000 SBC Table 3-30: LAN1 Ethernet Connector Pinouts .................47 Table 3-31: Connector LEDs ......................48 Table 3-32: USB 2.0 Port Pinouts ....................48 Table 3-33: Serial Port Pinouts ....................49 Table 4-1: AT/ATX Mode Select Switch Settings ...............55 Table 4-2: Clear BIOS Jumper Settings ..................56 Table 5-1: BIOS Navigation Keys ....................63 Page XII...
  • Page 13 gKINO-V/R1000 SBC List of BIOS Menus BIOS Menu 1: Main ........................64 BIOS Menu 2: Advanced ......................65 BIOS Menu 3: Trusted Computing ....................66 BIOS Menu 4: ACPI Settings .......................67 BIOS Menu 5: IDE Configuration ....................68 BIOS Menu 6: F81866 Super IO Configuration ................69 BIOS Menu 7: Serial Port n Configuration .................70 BIOS Menu 8: F81216 SEC Super IO Configuration ..............71 BIOS Menu 9: Serial Port n Configuration .................71...

  • Page 15: Introduction

    gKINO-V/R1000 SBC Chapter Introduction Page 1...

  • Page 16: Introduction

    gKINO-V/R1000 SBC 1.1 Introduction Figure 1-1: gKINO-V/R1000 The gKINO-V/R1000 series is a Mini-ITX form factor single bard computer. It has an ® on-board AMD Ryzen™ Embedded V1000/R1000 series processor, and supports two 260-pin 2400 MHz dual-channel ECC DDR4 SO-DIMM slots with up to 64.0 GB of memory.

  • Page 17: Model Variations

    gKINO-V/R1000 SBC 1.2 Model Variations The model variations of the gKINO-V/R1000 series are listed below. Model No. DisplayPort # gKINO-V1605B AMD® Ryzen™ Embedded V1605B gKINO-V1202B AMD® Ryzen™ Embedded V1202B gKINO-R1606G AMD® Ryzen™ Embedded R1606G gKINO-R1505G AMD® Ryzen™ Embedded R1505G Table 1-1: Model Variations 1.3 Features Some of the gKINO-V/R1000 motherboard features are listed below: ®...

  • Page 18: Connectors

    gKINO-V/R1000 SBC 1.4 Connectors The connectors on the gKINO-V/R1000 are shown in the figures below. Figure 1-2: Connectors Page 4...

  • Page 19: Dimensions

    gKINO-V/R1000 SBC 1.5 Dimensions The dimensions of the two models are listed below: Figure 1-3: gKINO-V1000 Dimensions (mm) Page 5...

  • Page 20: Figure 1-4: Gkino-R1000 Dimensions (Mm)

    SBC Figure 1-4: gKINO-R1000 Dimensions (mm) Page 6...

  • Page 21: Data Flow

    gKINO-V/R1000 SBC 1.6 Data Flow Figure 1-5 shows the data flow between the system chipset, the CPU and other components installed on the motherboard. Figure 1-5: Data Flow Diagram Page 7...

  • Page 22: Technical Specifications

    (OpenGL 4.2 and future OpenGL 4.3 will be supported when the driver upgrade is available for AMD Gen 2 R processors) Display Output gKINO-V1000: 4 x DP (4K UHD, 3840x2160) gKINO-R1000: 3 x DP (4K UHD, 3840x2160) Dual Realtek RTL8119I PCIe GbE controller Ethernet Digital I/O...
  • Page 23 gKINO-V/R1000 SBC Specification gKINO-V/R1000 I/O Interface 1 x Digital output connector (S/PDIF) Audio Connector 2 x 6W audio amplifier connector (L+R) 2 x Audio jack (line-out and mic-in) 1 x Front audio connector by 10-pin (2x5) header Ethernet 2 x RJ-45 GbE port 2 x RS-232 by DB-9 on rear I/O Serial Ports 4 x RS-232 by 10-pin (2x5) header...

  • Page 24: Table 1-2: Technical Specifications

    gKINO-V/R1000 SBC Specification gKINO-V/R1000 Power Consumption 12 V @ 5.144 A (AMD Ryzen V1605B 2.0 GHz CPU with 32 GB 2666 MHz DDR4 memory) 12 V @ 5.146 A (AMD Ryzen R1606G 2.6 GHz CPU with 32 GB 2666 MHz DDR4 memory) Operating: 0°C ~ 60°C Temperature Storage: -10°C ~ 70°C...

  • Page 25: Unpacking

    gKINO-V/R1000 SBC Chapter Unpacking Page 11...

  • Page 26: Anti-Static Precautions

    gKINO-V/R1000 SBC 2.1 Anti-static Precautions WARNING! Static electricity can destroy certain electronics. Make sure to follow the ESD precautions to prevent damage to the product, and injury to the user. Make sure to adhere to the following guidelines:  Wear an anti-static wristband: Wearing an anti-static wristband can prevent electrostatic discharge.

  • Page 27: Packing List

    The gKINO-V/R1000 is shipped with the following components: Quantity Item and Part Number Image gKINO-V/R1000 single board computer SATA cable I/O shielding for gKINO-V1000 I/O shielding for gKINO-R1000 Quick Installation Guide Page 13...

  • Page 28: Optional Items

    gKINO-V/R1000 SBC 2.4 Optional Items The following are optional components which may be separately purchased: Item and Part Number Image Dual USB cable (with bracket), 300mm, P=2.0 (P/N: CB-USB02A-RS) RS-232 cable, 300mm, P=2.0 (P/N: 19800-000300-100-RS) Infineon TPM module, 20-pin, firmware v5.5 (P/N: TPM-IN02-R20) Page 14...

  • Page 29: Connectors

    gKINO-V/R1000 SBC Chapter Connectors Page 15...

  • Page 30: Peripheral Interface Connectors

    gKINO-V/R1000 SBC 3.1 Peripheral Interface Connectors This chapter details all the jumpers and connectors. 3.1.1 gKINO-V/R1000 Layout The figures below show all the connectors and jumpers. Figure 3-1: Connector and Jumper Locations Page 16...

  • Page 31: Peripheral Interface Connectors

    gKINO-V/R1000 SBC 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board. Connector Type Label 12 V DC-IN power connector 4-pin Molex CPU12V1 Audio connector 10-pin header AUDIO2 SPK_L1, Audio amplifier connectors 2-pin wafer SPK_R1 Battery connector 2-pin wafer BAT1 ccTalk connectors...

  • Page 32: External Interface Panel Connectors

    gKINO-V/R1000 SBC SPI flash connector, EC 6-pin wafer JSPI_EC1 TPM connector 20-pin header TPM1 USB 2.0 connector 8-pin header USB_CON1 Table 3-1: Peripheral Interface Connectors 3.1.3 External Interface Panel Connectors The table below lists the connectors on the external I/O panel. Connector Type Label...

  • Page 33: Internal Peripheral Connectors

    gKINO-V/R1000 SBC 3.2 Internal Peripheral Connectors The section describes all of the connectors on the gKINO-V/R1000. 3.2.1 12 V DC-IN Power Connector CN Label: CPU12V1 4-pin Molex, p=4.2 mm CN Type: CN Location: See Figure 3-2 CN Pinouts: See Table 3-3 The connector supports the 12 V power supply.

  • Page 34: Audio Connector

    gKINO-V/R1000 SBC 3.2.2 Audio Connector CN Label: AUDIO2 CN Type: 10-pin header, p=2.54 mm CN Location: See Figure 3-3 CN Pinouts: See Table 3-4 The audio connector supporting High-Definition Audio is connected to external audio devices including speakers and microphones for the input and output of audio signals to and from the system.

  • Page 35: Audio Amplifier Connectors

    gKINO-V/R1000 SBC 3.2.3 Audio Amplifier Connectors CN Label: SPK_L1, SPK_R1 CN Type: 2-pin wafer, p=2.00 mm CN Location: See Figure 3-4 CN Pinouts: See Table 3-5 and Table 3-6 These connectors support 6 W Class-D audio amplifiers (L+R). Figure 3-4: Audio Amplifier Connector Locations Description SPK_L+ SPK_L-...

  • Page 36: Battery Connector

    gKINO-V/R1000 SBC 3.2.4 Battery Connector CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. NOTE: It is recommended to attach the RTC battery onto the system chassis in which the gKINO-V/R1000 is installed.

  • Page 37: Cctalk Connectors

    gKINO-V/R1000 SBC Description RTC Battery+ Table 3-7: Battery Connector Pinouts 3.2.5 ccTalk Connectors CN Label: COM7, COM8 CN Type: 4-pin wafer, p=2.5 mm CN Location: See Figure 3-6 CN Pinouts: See Table 3-8 The connectors provide ccTalk connections. Figure 3-6: ccTalk Connector Locations Description +12V ccTalk DATA...

  • Page 38: Chassis Intrusion Connector

    gKINO-V/R1000 SBC 3.2.6 Chassis Intrusion Connector CN Label: CHASSIS1 CN Type: 2-pin header, p=2.54 mm CN Location: See Figure 3-7 CN Pinouts: See Table 3-9 The chassis intrusion connector is for a chassis intrusion detection sensor or switch that detects if a chassis component is removed or replaced. Figure 3-7: Chassis Intrusion Connector Location Description CHASSIS OPEN#...

  • Page 39: Digital I/O Connector

    gKINO-V/R1000 SBC 3.2.7 Digital I/O Connector CN Label: DIO1 CN Type: 10-pin header, p=2.00 mm CN Location: See Figure 3-8 CN Pinouts: See Table 3-10 The 8-bit digital I/O connector provides programmable input and output for external devices. Figure 3-8: Digital I/O Connector Location Description Description Output 3...

  • Page 40: Ec Debug Connector

    gKINO-V/R1000 SBC 3.2.8 EC Debug Connector CN Label: CN Type: 20-pin FPC, p=0.5 mm CN Location: See Figure 3-9 CN Pinouts: See Table 3-11 The EC debug connector is used for EC debug. Figure 3-9: EC Debug Connector Location Description Description KSI0 KSO0...

  • Page 41: Fan Connectors

    gKINO-V/R1000 SBC 3.2.9 Fan Connectors CN Label: CPU_FAN1, SYS_FAN1 CN Type: 4-pin wafer, p=2.54 mm CN Location: See Figure 3-10 CN Pinouts: See Table 3-12 The fan connector attaches to a cooling fan. Figure 3-10: Fan Connector Locations Description FAN_IO Table 3-12: Fan Connector Pinouts Page 27...

  • Page 42: Front Panel Connector

    gKINO-V/R1000 SBC 3.2.10 Front Panel Connector CN Label: F_PANEL1 CN Type: 14-pin header, p=2.54 mm CN Location: See Figure 3-11 CN Pinouts: See Table 3-13 The front panel connector connects to the indicator LEDs and buttons on the system front panel.

  • Page 43: I 2 C Connector

    gKINO-V/R1000 SBC 3.2.11 I C Connector CN Label: I2C1 CN Type: 4-pin wafer, p=1.25 mm CN Location: See Figure 3-12 CN Pinouts: See Table 3-14 The I C connector is used to connect I C-bus devices to the mainboard. Figure 3-12: I C Connector Location Description I2C_DAT...

  • Page 44: Lan Led Connectors

    gKINO-V/R1000 SBC 3.2.12 LAN LED Connectors CN Label: LED_LAN1, LED_LAN2 CN Type: 2-pin header, p=2.54 mm CN Location: See Figure 3-13 CN Pinouts: See Table 3-15 The LAN LED connectors connect to the LAN link LEDs on the system. Figure 3-13: LAN LED Connector Locations Description +3.3V LAN_LED_LNK#_ACT...

  • Page 45: Slot

    gKINO-V/R1000 SBC 3.2.13 M.2 Slot CN Label: M2_M2 CN Type: M.2 M-key slot CN Location: See Figure 3-14 CN Pinouts: See Table 3-16 The M.2 slot is keyed in the M position. The M.2 slot supports SATA and PCIe 3.0 x2 signals.

  • Page 46: Table 3-16: M.2 M-Key Slot Pinouts

    gKINO-V/R1000 SBC Description Description PCIE_RXN1 PCIE_RXP1 PCIE_TXN1 PCIE_TXP1 DEVSLP PCIE_RXN0 PCIE_RXP0 PCIE_TXN0 PCIE_TXP0 PERST# CLKREQ# REFCLKN PEWAKE REFCLKP Module Key Module Key Module Key Module Key Module Key Module Key Module Key Module Key SUSCLK PEDET +3.3V +3.3V +3.3V Table 3-16: M.2 M-Key Slot Pinouts Page 32...

  • Page 47: Pcie X16 Slot

    gKINO-V/R1000 SBC 3.2.14 PCIe x16 Slot CN Label: PCIEX16 CN Type: PCIe x16 slot CN Location: See Figure 3-15 The PCIe x16 slot supports PCIe x8 expansion cards. Figure 3-15: PCIe x16 Slot Location 3.2.15 RS-232 Serial Port Connectors (COM3 ~ COM6) CN Label: COM3, COM4, COM5, COM6 CN Type:...

  • Page 48: Figure 3-16: Rs-232 Serial Port Connector Locations

    gKINO-V/R1000 SBC Figure 3-16: RS-232 Serial Port Connector Locations Description Description Table 3-17: RS-232 Serial Port Connector Pinouts Page 34...

  • Page 49: Sata 6Gb/S Drive Connector

    gKINO-V/R1000 SBC 3.2.16 SATA 6Gb/s Drive Connector CN Label: S_ATA1 CN Type: 7-pin SATA connector CN Location: See Figure 3-17 CN Pinouts: See Table 3-18 The SATA 6Gb/s drive connector is connected to a SATA 6Gb/s drive. The SATA 6Gb/s drive transfers data at speeds as high as 6Gb/s.

  • Page 50: Sata Power Connector

    gKINO-V/R1000 SBC 3.2.17 SATA Power Connector CN Label: SATA_PWR1 CN Type: 4-pin wafer, p=2.5 mm CN Location: See Figure 3-18 CN Pinouts: See Table 3-19 The SATA power connector provides +5 V and +12 V power output to the SATA connector.

  • Page 51: Smbus Connector

    gKINO-V/R1000 SBC 3.2.18 SMBus Connector CN Label: SMB1 CN Type: 4-pin wafer, p=1.25 mm CN Location: See Figure 3-19 CN Pinouts: See Table 3-20 The SMBus (System Management Bus) connector provides low-speed system management communications. Figure 3-19: SMBus Connector Location Description SMB_DATA SMB_CLK...

  • Page 52: S/Pdif Connector

    gKINO-V/R1000 SBC 3.2.19 S/PDIF Connector CN Label: SPDIF1 CN Type: 5-pin header, p=2.54 mm CN Location: See Figure 3-20 CN Pinouts: See Table 3-21 Use the S/PDIF connector to connect digital audio devices to the system. Figure 3-20: S/PDIF Connector Location Description SPDIF OUT SPDIF IN...

  • Page 53: Spi Flash Connector, Bios

    gKINO-V/R1000 SBC 3.2.20 SPI Flash Connector, BIOS CN Label: JSPI_BIOS_1 CN Type: 6-pin wafer, p=1.25 mm CN Location: See Figure 3-21 CN Pinouts: See Table 3-22 The 6-pin SPI Flash connector is used to flash the BIOS. Figure 3-21: BIOS SPI Flash Connector Location Description +3.3V SPI_CS#...

  • Page 54: Spi Flash Connector, Ec

    gKINO-V/R1000 SBC 3.2.21 SPI Flash Connector, EC CN Label: JSPI_EC1 CN Type: 6-pin wafer, p=1.25 mm CN Location: See Figure 3-22 CN Pinouts: See Table 3-23 The 6-pin SPI Flash connector is used to flash the EC. Figure 3-22: EC SPI Flash Connector Location Description +3.3V SPI_CS#...

  • Page 55: Tpm Connector

    gKINO-V/R1000 SBC 3.2.22 TPM Connector CN Label: TPM1 CN Type: 20-pin header, p=2.54 mm CN Location: See Figure 3-23 CN Pinouts: See Table 3-24 The Trusted Platform Module (TPM) connector secures the system on bootup. Figure 3-23: TPM Connector Location Description Description LCLK...

  • Page 56: Usb 2.0 Connector

    gKINO-V/R1000 SBC 3.2.23 USB 2.0 Connector CN Label: USB_CON1 CN Type: 8-pin header, p=2.00 mm CN Location: See Figure 3-24 CN Pinouts: See Table 3-25 The USB connector provides two USB 2.0 ports by dual-port USB cable. Figure 3-24: USB Connector Location Description Description DATA-...

  • Page 57: External Peripheral Interface Connector Panel

    gKINO-V/R1000 SBC 3.3 External Peripheral Interface Connector Panel Figure 3-25 shows the gKINO-V/R1000 external peripheral interface connector (EPIC) panel. The EPIC panel consists of the following:  2 x Audio jack (AUDIO1)  1 x DC-in power jack (PWR_IN1)  DisplayPort connectors (DP0_1, DP2_3) ...

  • Page 58: Audio Jacks

    gKINO-V/R1000 SBC 3.3.1 Audio Jacks CN Label: AUDIO1 CN Type: Audio jack CN Location: See Figure 3-25 The audio jacks connect to external audio devices.  Line Out port (Lime): Connects to a headphone or a speaker. With multi-channel configurations, this port can also connect to front speakers. ...

  • Page 59: Displayport Connectors

    gKINO-V/R1000 SBC 3.3.2 DisplayPort Connectors CN Label: DP0_1, DP2_3 CN Type: DisplayPort connector CN Location: See Figure 3-25 CN Pinouts: See Table 3-26 and Figure 3-27 Each DisplayPort connector can connect to a DisplayPort device. Description Description DATA_0P DATA_3N DATA_0N CONFIG1 DATA_1P CONFIG2...

  • Page 60: Lan And Usb 3.2 Gen 1 Combo Connector

    gKINO-V/R1000 SBC 3.3.3 LAN and USB 3.2 Gen 1 Combo Connector CN Label: LAN1_USB1, LAN2_USB2 CN Type: RJ-45 and USB 3.2 Type A combo CN Location: See Figure 3-25 CN Pinouts: See Table 3-27 and Table 3-29 A 10/100/1000 Mb/s connection can be made to a Local Area Network. Description Description MDIA0+...

  • Page 61: Lan And Usb 2.0 Combo Connector

    gKINO-V/R1000 SBC Description Description USB_DATA+ USB_ DATA+ USB3_RX- USB3_RX- USB3_RX+ USB3_ RX+ USB3_TX- USB3_TX- USB3_TX+ USB3_TX+ Table 3-29: USB 3.2 Gen 1 Port Pinouts 3.3.4 LAN and USB 2.0 Combo Connector CN Label: LAN2_USB2 CN Type: RJ-45 and USB 2.0 Type A combo CN Location: See Figure 3-25 CN Pinouts:...

  • Page 62: Power Connector

    gKINO-V/R1000 SBC Description Description on: linked off: 10 Mb/s blinking: data is being sent/received green: 100 Mb/s orange: 1000 Mb/s Table 3-31: Connector LEDs The USB 2.0 connector can be connected to a USB device. Description Description USB_DATA- USB_DATA- USB_DATA+ USB_ DATA+ Table 3-32: USB 2.0 Port Pinouts 3.3.5 Power Connector...

  • Page 63: Serial Port Connectors (Com1, Com2)

    gKINO-V/R1000 SBC 3.3.6 Serial Port Connectors (COM1, COM2) CN Label: COM1_2 CN Type: DB-9 connectors CN Location: See Figure 3-25 CN Pinouts: See Table 3-33 and Figure 3-31 The serial port connects to a RS-232 serial communications device. Description Description Table 3-33: Serial Port Pinouts Figure 3-31: Serial Port Pinouts Page 49...

  • Page 64: Installation

    gKINO-V/R1000 SBC Chapter Installation Page 50...

  • Page 65: Anti-Static Precautions

    gKINO-V/R1000 SBC 4.1 Anti-static Precautions WARNING: Failure to take ESD precautions during the installation of the gKINO-V/R1000 result permanent damage gKINO-V/R1000 and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the gKINO-V/R1000. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the gKINO-V/R1000, or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
  • Page 66 gKINO-V/R1000 SBC WARNING: The installation instructions described in this manual should be carefully followed in order to prevent damage to the components and injury to the user. Before and during the installation please DO the following:  Read the user manual: The user manual provides a complete description of the gKINO-V/R1000 installation instructions and configuration options.

  • Page 67: So-Dimm Installation

    gKINO-V/R1000 SBC 4.3 SO-DIMM Installation To install an SO-DIMM, please follow the steps below and refer to Figure 4-1. Figure 4-1: SO-DIMM Installation Step 1: Locate the SO-DIMM socket. Place the board on an anti-static mat. Step 2: Align the SO-DIMM with the socket. Align the notch on the memory with the notch on the memory socket.

  • Page 68: Module Installation

    gKINO-V/R1000 SBC 4.4 M.2 Module Installation The M.2 slot is keyed in the M position and provides mounting screw position for 2280-size or 2242-sizze M.2 module. To install an M.2 module, follow the steps below. Step 1: Locate the M.2 module slot. See Chapter 3. Step 2: Remove the on-board retention screw Figure 4-2.

  • Page 69: System Configuration

    gKINO-V/R1000 SBC Step 4: Push the M.2 module down and secure it with the previously removed retention screw (Figure 4-4). Figure 4-4: Securing the M.2 Module 4.5 System Configuration The system configuration is controlled by buttons, jumpers and switches. The system configuration should be performed before installation.

  • Page 70: Clear Cmos

    gKINO-V/R1000 SBC Figure 4-5: AT/ATX Mode Select Switch Location 4.5.2 Clear CMOS To reset the BIOS, move the jumper to the "Clear BIOS" position for 3 seconds or more, then move back to the default position. Setting Description Keep current BIOS setup Clear BIOS Table 4-2: Clear BIOS Jumper Settings The location of the clear CMOS button (JP1) is shown in Figure 4-6...

  • Page 71: Chassis Installation

    gKINO-V/R1000 SBC 4.6 Chassis Installation 4.6.1 Airflow WARNING: Airflow is critical for keeping components within recommended operating temperatures. The chassis should have fans and vents as necessary to keep things cool. The gKINO-V/R1000 must be installed in a chassis with ventilation holes on the sides allowing airflow to travel through the heat sink surface.

  • Page 72: Figure 4-7: Sata Drive Cable Connection

    gKINO-V/R1000 SBC Figure 4-7: SATA Drive Cable Connection Step 3: Connect the cable to the SATA disk. Connect the connector on the other end of the cable to the connector at the back of the SATA drive. See Figure 4-7. Step 4: To remove the SATA cable from the SATA connector, press the clip on the connector at the end of the cable.

  • Page 73: Available Drivers

    gKINO-V/R1000 SBC 4.8 Available Drivers All the drivers for the gKINO-V/R1000 are available on IEI Resource Download Center (https://download.ieiworld.com). Type gKINO-V/R1000 and press Enter to find all the relevant software, utilities, and documentation. Figure 4-8: IEI Resource Download Center 4.8.1 Driver Download To download drivers from IEI Resource Download Center, follow the steps below.
  • Page 74 gKINO-V/R1000 SBC Step 3: Click the driver file name on the page and you will be prompted with the  following window. You can download the entire ISO file ( ), or double click an  individual item to find its driver file and click the file name to download ( NOTE: To install software from the downloaded ISO image file in Windows 10, double-click the ISO file to mount it as a virtual drive to view its content.

  • Page 75: Bios

    gKINO-V/R1000 SBC Chapter BIOS Page 61...

  • Page 76: Introduction

    gKINO-V/R1000 SBC 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.

  • Page 77: Getting Help

    gKINO-V/R1000 SBC Function Decrease the numeric value or make changes F1 key General help, only for Status Page Setup Menu and Option Page Setup Menu F2 key Load previous values. F3 key Load optimized defaults F4 key Save changes and Exit BIOS Esc key Main Menu –...

  • Page 78: Main

    gKINO-V/R1000 SBC The following sections completely describe the configuration options found in the menu items at the top of the BIOS screen and listed above. 5.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information.

  • Page 79: Advanced

    gKINO-V/R1000 SBC 5.3 Advanced Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus: WARNING! Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.

  • Page 80: Trusted Computing

    gKINO-V/R1000 SBC 5.3.1 Trusted Computing Use the Trusted Computing menu (BIOS Menu 3) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM). Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced Configuration Enables or Disables BIOS Security Device Support [Disable] support for security...

  • Page 81: Acpi Settings

    gKINO-V/R1000 SBC 5.3.2 ACPI Settings The ACPI Settings menu (BIOS Menu 4) configures the Advanced Configuration and Power Interface (ACPI) options. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced ACPI Settings Select the highest ACPI sleep state the system ACPI Sleep State [S3 (Suspend to RAM] will enter when the...

  • Page 82: Ide Configuration

    gKINO-V/R1000 SBC 5.3.3 IDE Configuration Use the IDE Configuration menu (BIOS Menu 5) to change and/or set the configuration of the SATA devices installed in the system. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced IDE Configuration SATA Port 0 Not Present ---------------------...

  • Page 83: F81866 Super Io Configuration

    gKINO-V/R1000 SBC 5.3.4 F81866 Super IO Configuration Use the F81866 Super IO Configuration menu (BIOS Menu 6) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced F81866 Super IO Configuration Set Parameters of Serial Port 1 (COMA) Super IO Chip...

  • Page 84: Serial Port N Configuration

    gKINO-V/R1000 SBC 5.3.4.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 7) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced Serial Port 1 Configuration Enable or Disable Serial Port (COM) Serial Port [Enabled]...

  • Page 85: F81216 Sec. Super Io Configuration

    gKINO-V/R1000 SBC 5.3.5 F81216 Sec. Super IO Configuration Use the F81216 Sec. Super IO Configuration menu (BIOS Menu 8) to set or change the configurations for the serial ports. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced F81216SEC Super IO Configuration Set Parameters of Serial Port 1 (COMG)

  • Page 86: Iwdd H/W Monitor

    gKINO-V/R1000 SBC  Serial Port [Enabled] Use the Serial Port option to enable or disable the serial port.  Disable the serial port Disabled  Enabled Enable the serial port EFAULT 5.3.6 iWDD H/W Monitor The iWDD H/W Monitor menu (BIOS Menu 10) contains the fan configuration submenus and displays operating temperature, fan speeds and system voltages.

  • Page 87: Smart Fan Mode Configuration

    gKINO-V/R1000 SBC CPU Fan Speed System Fan Speed  Voltages CPU_CORE +DDR +5VSB +3.3V +3.3VSB 5.3.6.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 11) to configure fan temperature and speed settings. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced Smart Fan Mode Configuration Smart Fan Mode Select...
  • Page 88 gKINO-V/R1000 SBC  The fan adjusts its speed using these Auto Mode EFAULT settings: Auto mode fan start temperature Auto mode fan off temperature Auto mode fan start PWM Auto mode fan slope PWM  Auto mode fan start temperature WARNING: Setting this value too high may cause the fan to rotate at full speed only when the CPU is at a very high temperature and therefore cause the...
  • Page 89 gKINO-V/R1000 SBC lowest. To set a value, select the Auto mode fan off temperature option and enter a decimal number between 1 and 100.  Auto mode fan start PWM The Auto mode fan start PWM option can only be set if the CPU_FAN1/SYS_FAN1 Smart Fan control option is set to Auto Mode.

  • Page 90: Rtc Wake Settings

    gKINO-V/R1000 SBC 5.3.7 RTC Wake Settings The RTC Wake Settings menu (BIOS Menu 12) configures RTC wake event. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event. When enabled, System will wake on the date::hr::min::sec...

  • Page 91: Power Saving Configuration

    gKINO-V/R1000 SBC Wake up second After setting the alarm, the computer turns itself on from a suspend state when the alarm goes off. 5.3.8 Power Saving Configuration Use the Power Saving Configuration menu (BIOS Menu 13) to configure power saving function and USB power.

  • Page 92: Cpu Configuration

    gKINO-V/R1000 SBC 5.3.9 CPU Configuration Use the CPU Configuration menu (BIOS Menu 14) to view detailed CPU specifications and configure the CPU. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced CPU Configuration Enable/disable No-execute page Module Version: PiccasoCpu 10 protection Function AGESA Version: PiccasoPI 1005 NX Mode...

  • Page 93: Node 0 Information

    gKINO-V/R1000 SBC 5.3.9.1 Node 0 Information Use the Node 0 Information menu (BIOS Menu 15) to view memory information related to Node 0. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced Socket0 : AMD Ryzen Embedded R1606G with Radeon Vega Gfx 2 Core(s) Running @ 2630 MHz 1218 mV Processor Family: 17h Processor Model: 10h-1Fh...

  • Page 94: Usb Configuration

    gKINO-V/R1000 SBC 5.3.10 USB Configuration Use the USB Configuration menu (BIOS Menu 16) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced USB Configuration Enables Legacy USB support. AUTO option USB Module Version disables legacy support if no USB devices are...

  • Page 95: Nvme Configuration

    gKINO-V/R1000 SBC 5.3.11 NVMe Configuration Use the NVMe Configuration menu (BIOS Menu 17) to change and/or set the configuration of the NVMe devices installed in the system. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced NVMe Configuration No NVME Device Found --------------------- : Select Screen...

  • Page 96: Amd Cbs

    gKINO-V/R1000 SBC 5.3.12 AMD CBS The AMD CBS menu (BIOS Menu 18) configures CPU-related information. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced AMD CBS NBIO Common Options > NBIO Common Options ---------------------- > FCH Common Options : Select Screen ↑...

  • Page 97: Gfx Configuration

    gKINO-V/R1000 SBC  Audio IOs [ENABLE AUDIO IOs] Use the Audio IOs option to enable or disable the audio IO interfaces.  The audio IO interfaces are enabled ENABLE EFAULT AUDIO  DISABLE The audio IO interfaces are disabled AUDIO 5.3.12.1.1 GFX Configuration Use the GFX Configuration menu (BIOS Menu 20) to configure the graphics controller.

  • Page 98: Fch Common Options

    gKINO-V/R1000 SBC  The integrated graphics controller is disabled Disabled  Forces Forces the use of the integrated graphics controller  Auto integrated graphics controller detected EFAULT automatically and enabled  NB Azalia [Enabled] Use the NB Azalia option to enable or disable the High Definition Audio controller. ...

  • Page 99: Sata Configuration Options

    gKINO-V/R1000 SBC 5.3.12.2.1 SATA Configuration Options Use the SATA Configuration Options menu (BIOS Menu 22) to configure Serial ATA. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced SATA Configuration Options Disable or enable OnChip SATA controller SATA Controller [Enabled] SATA Mode [AHCI]...

  • Page 100: Amd Pbs

    gKINO-V/R1000 SBC 5.3.13 AMD PBS The AMD CBS menu (BIOS Menu 23) configures CPU-related information. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Advanced > AMD Firmware Version Show all of AMD Firmware Version ---------------------- : Select Screen ↑...

  • Page 101: South Bridge

    gKINO-V/R1000 SBC Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit > South Bridge South Bridge Parameters > GFX Configuration > North Bridge --------------------- : Select Screen ↑ ↓: Select Item Enter Select +/-: Change Opt.

  • Page 102: North Bridge

    gKINO-V/R1000 SBC  The system remains turned off Power Off  Power On The system turns on  Last State The system returns to its previous state. If it was on, it EFAULT turns itself on. If it was off, it remains off. 5.4.2 North Bridge Use the North Bridge menu (BIOS Menu 26) to configure the memory settings.

  • Page 103: Security

    gKINO-V/R1000 SBC 5.5 Security Use the Security menu (BIOS Menu 27) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Password Description Set Administrator Password If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup...

  • Page 104: Boot

    gKINO-V/R1000 SBC 5.6 Boot Use the Boot menu (BIOS Menu 28) to configure system boot options. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Boot Configuration Select the keyboard Bootup NumLock State [On] NumLock state Quiet Boot...
  • Page 105 gKINO-V/R1000 SBC  Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots.  Normal POST messages displayed Disabled  Enabled OEM Logo displayed instead of POST messages EFAULT  Launch PXE OpROM [Disabled] Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices.

  • Page 106: Save & Exit

    gKINO-V/R1000 SBC 5.7 Save & Exit Use the Save & Exit menu (BIOS Menu 29) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2020 American Megatrends, Inc. Main Advanced Chipset Security Boot...
  • Page 107 gKINO-V/R1000 SBC  Save as User Defaults Use the Save as User Defaults option to save the changes done so far as user defaults.  Restore User Defaults Use the Restore User Defaults option to restore the user defaults to all the setup options. Page 93...

  • Page 108: A Regulatory Compliance

    gKINO-V/R1000 SBC Appendix Regulatory Compliance Page 94...
  • Page 109 gKINO-V/R1000 SBC DECLARATION OF CONFORMITY This equipment has been tested and found to comply with specifications for CE marking. If the user modifies and/or installs other devices in the equipment, the CE conformity declaration may no longer apply. FCC WARNING This equipment complies with Part 15 of the FCC Rules.

  • Page 110: B Product Disposal

    gKINO-V/R1000 SBC Appendix Product Disposal Page 96...
  • Page 111 gKINO-V/R1000 SBC CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations.  Outside the European Union–If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.

  • Page 112: Cbios Menu Options

    gKINO-V/R1000 SBC Appendix BIOS Menu Options Page 98...
  • Page 113 gKINO-V/R1000 SBC System Date [xx/xx/xx] ......................64 System Time [xx:xx:xx] .......................64 Security Device Support [Disable] ..................66 ACPI Sleep State [S3 (Suspend to RAM)] ................67 Case Open Beep [Disabled] ....................69 Serial Port [Enabled] ......................70 Serial Port [Enabled] ......................72 PC Health Status ........................72 CPU_FAN1/SYS_FAN1 Smart Fan Control [Auto Mode] ..........73 Auto mode fan start temperature ..................74 Auto mode fan off temperature ..................74...
  • Page 114 gKINO-V/R1000 SBC Discard Changes and Reset ....................92 Restore Defaults ........................92 Save as User Defaults ......................93 Restore User Defaults ......................93 Page 100...

  • Page 115: D Digital I/O Interface

    gKINO-V/R1000 SBC Appendix Digital I/O Interface Page 101...
  • Page 116 gKINO-V/R1000 SBC The DIO connector on the gKINO-V/R1000 is interfaced to GPIO ports on the Super I/O chipset. The DIO has both 8-bit digital inputs and 8-bit digital outputs. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices.
  • Page 117 gKINO-V/R1000 SBC AH – 6FH Sub-function: AL – 9 :Set the digital port as OUTPUT :Digital I/O output value Assembly Language Sample 2 AX, 6F09H ;setting the digital port as output BL, 09H ;digital value is 09H Digital Output is 1001b Page 103...

  • Page 118: E Watchdog Timer

    gKINO-V/R1000 SBC Appendix Watchdog Timer Page 104...
  • Page 119 gKINO-V/R1000 SBC NOTE: The following discussion applies to DOS. Contact IEI support or visit the IEI website for drivers for other operating systems. The Watchdog Timer is a hardware-based timer that attempts to restart the system when it stops working. The system may stop working because of external EMI or software bugs. The Watchdog Timer ensures that standalone systems like ATMs will automatically attempt to restart in the case of system problems.
  • Page 120 gKINO-V/R1000 SBC NOTE: The Watchdog Timer is activated through software. The software application that activates the Watchdog Timer must also deactivate it when closed. If the Watchdog Timer is not deactivated, the system will automatically restart after the Timer has finished its countdown. EXAMPLE PROGRAM: ;...

  • Page 121: F Error Beep Code

    gKINO-V/R1000 SBC Appendix Error Beep Code Page 107...

  • Page 122: Pei Beep Codes

    gKINO-V/R1000 SBC F.1 PEI Beep Codes Number of Beeps Description Memory not Installed Memory was installed twice (InstallPeiMemory routine in PEI Core called twice) Recovery started DXEIPL was not found DXE Core Firmware Volume was not found Recovery failed S3 Resume failed Reset PPI is not available F.2 DXE Beep Codes Number of Beeps...

  • Page 123: G Hazardous Materials Disclosure

    gKINO-V/R1000 SBC Appendix Hazardous Materials Disclosure Page 109...

  • Page 124: Rohs Ii Directive (2015/863/Eu)

    gKINO-V/R1000 SBC G.1 RoHS II Directive (2015/863/EU) The details provided in this appendix are to ensure that the product is compliant with the RoHS II Directive (2015/863/EU). The table below acknowledges the presences of small quantities of certain substances in the product, and is applicable to RoHS II Directive (2015/863/EU).

  • Page 125: China Rohs

    gKINO-V/R1000 SBC G.2 China RoHS 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符 合中国 RoHS 标准规定的限量要求。 本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的 年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些 元件将会单独标示出来。 部件名称 有毒有害物质或元素 壳体 印刷电路板 金属螺帽 电缆组装 风扇组装 电力供应组装 电池 O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11364-2014 與 GB/T26572-2011 标准规定的限量要求以下。 X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11364-2014 與 GB/T26572-2011 标准规定的限量要求。 Page 111...

This manual is also suitable for:

Gkino-v1000Gkino-v1605bGkino-v1202bGkino-r1606gGkino-r1505gGkino-v1202b-r10 ... Show all

Table of Contents