Hisense 65WR60AE Manual page 21

Ｏｎ
ＰＣ ｔｏ
ｄｅｖｉｃｅ
Ｏｎ
Ｄｅｖｉｃｅ ｔｏ
Switch on/
ＰＣ
off
Ｏｆｆ
ＰＣ ｔｏ
ｄｅｖｉｃｅ
Ｏｆｆ
Ｄｅｖｉｃｅ ｔｏ
ＰＣ
ＰＣ ｔｏ
ｄｅｖｉｃｅ
Ｄｅｖｉｃｅ ｔｏ
Volume
ＰＣ
Control
Ｒｅｍａｒｋ
ＰＣ ｔｏ
ｄｅｖｉｃｅ
Bright- Ｄｅｖｉｃｅ ｔｏ
ＰＣ
ness
Control
Ｒｅｍａｒｋ
NOTE
• Verify is the exclusive OR of Length, Command code, ID and Data.
• All data are hexadecimal values.
• For all commands received by the device, the protocol header needs to be changed to AB AB and the
protocol tail needs to be changed to CD CD when returning to the PC.
• Precautions for control terminal programming: For the power-on command, AB AB 01 04 A1 00 00 00
CD CD are returned after the power-on action is executed; if the command is not received, the power-on
command needs to be sent again. After the TV is turned on, the PC will receive AB AB 01 04 A1 00 00 00
CD CD again, and then the PC can send a control command to the device. If the correct command is not
returned after any command is sent, the command should be sent again at least after 500ms.
• In standby state, the device only supports startup commands.
Serial Protocol
Protocol
ID
header
ＤＤ ＦＦ ０１
ＡＢ ＡＢ ０１
ＤＤ ＦＦ ０１
ＡＢ ＡＢ ０１
ＤＤ ＦＦ ０１
ＡＢ ＡＢ ０１
ＸＸ ｉｓ ｔｈｅ ｖｏｌｕｍｅ ｖａｌｕｅ．
ＤＤ ＦＦ ０１
ＡＢ ＡＢ ０１
ＸＸ ｉｓ ｔｈｅ ｂｒｉｇｈｔｎｅｓｓ ｖａｌｕｅ．
Length Command code
０４ Ａ１ ００
０４ Ａ１ ００
０４ Ａ１ ０１
０４ Ａ１ ０１
０４ Ａ１ ０７
０４ Ａ１ ０７
０４ Ａ１ ０８
０４ Ａ１ ０８
15
Protocol tail
００ ００ ＢＢ
００ ００ ＣＤ
００ ００ ＢＢ
００ ００ ＣＤ
００ ＸＸ ＢＢ
００ ＸＸ ＣＤ
００ ＸＸ ＢＢ
００ ＸＸ ＣＤ
ＣＣ
ＣＤ
ＣＣ
ＣＤ
ＣＣ
ＣＤ
ＣＣ
ＣＤ