Panasonic WJ-HD309A Operating Instructions Manual page 120

MAN. (MANUAL): The recording duration will be as follows
depending on the event type.
• At a motion detection: For 8 seconds
• At a video loss occurrence: During a video loss occur-
rence
• At a terminal alarm occurrence: During the supply of a
signal
• At a command alarm: For 8 seconds
CON. (CONTINUE): Recording will be performed continu-
ously until the ALARM RESET button is pressed.
Notes:
• When "MAN." is selected for the recording duration,
recording will be performed for 8 seconds at least at an
event occurrence as long as the alarm is not canceled.
• Available recording duration for pre-event recording will
differ depending on the settings of "Resolution" and
"Recording Rate and Quality" for pre-event recording as
below:
Recording FRAME 3D ON
rate FRAME 3D OFF
0.1 5 min
0.2 2 min
0.3 1 min
0.4 1 min
0.5 1 min
1 30 s
2 10 s
3 10 s
5 7 s
6 6 s
7.5 4 s
10 3 s
15 2 s
30 1 s
60 -
• When a pre-recording area is created in an optional
extension unit (WJ-HDE300 series), it is possible to per-
form pre-event recording for up to 60 minutes accord-
ing to the resolution, recording rate and disk space for
pre-event recording. Refer to page 147 for descriptions
of how to create the pre-recording area.
• Pre-event recording for the camera channel that has the
pre-recording area in the extension unit will always be
performed on the pre-recording area.
• When a value that is impossible to be applied is set for
the pre-event recording, the relevant value will turn red,
and it will be impossible to close the recording program
window. In this case, lower the recording rate that has
turned red.
Recording Program 1
120
FIELD SIF
10 min 20 min
5 min 10 min
3 min 6 min
2 min 5 min
2 min 4 min
1 min 2 min
30 s 1 min
20 s 30 s
10 s 20 s
10 s 20 s
9 s 10 s
7 s 10 s
4 s 9 s
2 s 4 s
1 s -
I
Resolution FIELD
I
Recording Table 60 ips
I
Total REC Rate 48 ips
MANUAL SCHEDULE PRE EVENT POST EVENT
RATE QUALITY RATE QUALITY RATE QUALITY TIME RATE QUALITY TIME
CAM1 3ips FQB OFF FQB OFF FQB 10s 1ips FQB 30s
CAM2 OFF OFF 1ips
3ips FQB FQB FQB 10s FQB 30s
CAM3
3ips FQB OFF FQB OFF FQB 10s 1ips FQB 30s
CAM4 3ips FQB OFF FQB OFF FQB 10s 1ips FQB 30s
CAM5 3ips FQB OFF FQB OFF FQB 1ips FQB 30s
10s
CAM6 1ips
3ips FQB OFF FQB OFF FQB 10s FQB 30s
CAM7
3ips FQB OFF FQB OFF FQB 10s 1ips FQB 30s
CAM8 3ips FQB OFF FQB OFF FQB 10s 1ips FQB 30s
CAM9 3ips FQB OFF FQB OFF FQB 1ips FQB 30s
10s
CAM10 1ips
3ips FQB OFF FQB OFF FQB 10s FQB 30s
CAM11
3ips FQB OFF FQB OFF FQB 10s 1ips FQB 30s
CAM12 3ips FQB OFF FQB OFF FQB 10s 1ips FQB 30s
CAM13 OFF OFF 1ips
3ips FQB FQB FQB 10s FQB 30s
CAM14
3ips FQB OFF FQB OFF FQB 10s 1ips FQB 30s
CAM15 3ips FQB OFF FQB OFF FQB 10s 1ips FQB 30s
CAM16 3ips OFF FQB OFF FQB 1ips FQB 30s
FQB 10s
O K CANCEL
• When the recording rate is low, images may be record-
ed for a longer duration than the set pre-event record-
ing duration.
• Pre-event recording will not be performed for a camera
channel whose post-event recording rate is OFF.
• Audio will be recorded up to for 16 seconds before the
event occurrence. However, audio will not be recorded
during pre-event recording that is being performed in
the HDD pre-recording area.
• In case that the pre-event recording is to be performed,
when two or more events occur continuously in a
moment, the start time of the post-event recording of
the second event and later will be delayed respectively.
(The actual time and date of the event occurrences will
be recorded on the event log.) In this case, the start
time of the pre-event recording will be delayed auto-
matically.
When performing the pre-event recording in an environ-
ment where two or more events may occur at short
times frequently, it is recommended to set the pre-
recording duration longer.
Important:
Pre-event recording image only just recorded will be delet-
ed in the following cases:
• When the SETUP MENU is closed after changing the
settings
• When post-event recording is newly performed
• When the time zone of a schedule switched and record-
ing had just started
• When the date has been changed
G [Event Program] Create event programs for
an event occurrence
Perform the settings of event action for each event type
(motion detection, video loss, terminal/command alarm) or
of auto copy.
SETUP MENU
System Recording
Advanced
Switcher Display
I
Event Program 1
Time Table
I
Event Program 2
REC Program
I
Event Program 3
I
Event Program
Event Program 4
Special Days
Quick Menu
SETUP MENU
System Recording
Advanced
Switcher Display
I
Event Program 1
Time Table
I
Event Program 2
REC Program
I
Event Program 3
I
Event Program Event Action 4
Event Program 1
I
VMD
Special Days
I
Video Loss
I
Terminal/Command Alarm
Quick Menu
Event Schedule
LIVE
Comm Maintenance
SETUP
SETUP
SETUP
SETUP
Event Schedule
LIVE
Comm Maintenance
SETUP
SETUP
SETUP
SETUP
SETUP
SETUP
SETUP
O K CANCEL