Raven VSN Installation Manual
  1. Manuals
  2. Brands
  3. Raven Manuals
  4. Farm Equipment
  5. VSN
  6. Installation manual

Raven VSN Installation Manual

Hide thumbs Also See for VSN:
Table of Contents

Advertisement

Quick Links

Download this manual
VSN® Installation Manual
for Case AFS Connect
Steiger and New Holland
PLM T9 (Model Year 2021
and Newer)
016-2022-025 Rev. A
3/2022
E40317
Copyright 2022

Advertisement

Table of Contents
loading

Related Manuals for Raven VSN

Summary of Contents for Raven VSN

  • Page 1 VSN® Installation Manual for Case AFS Connect Steiger and New Holland PLM T9 (Model Year 2021 and Newer) 016-2022-025 Rev. A 3/2022 E40317 Copyright 2022...
  • Page 2 Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services. Raven Industries accepts no responsibility for the use of any of these signals or services for other than the stated purpose.

  • Page 3: Table Of Contents

    ................................. 6 Point of Reference .................................. 6 Updates ...................................6 Kit Contents ................................... 7 Chapter 3 Installation ....................... 9 fabricate the vsn® unit bracket ..........................9 VSN® Specifications ..............................9 mounting ....................................9 System Diagram ................................ 13 Route the Cables ............................... 14 Install the (Optional) Analog Video Kit ......................
  • Page 4 Table of Contents ii VSN® Installation Manual for Case AFS Connect Steiger and New Holland PLM T9 (MY 2021 and Newer)

  • Page 5: Chapter 1 Important Information

    • Do not operate this Raven system or any agricultural equipment while under the influence of alcohol or an illegal substance. • Be alert and aware of surroundings and remain in the operator seat at all times when operating this Raven system.

  • Page 6: Electrical Safety

    • Avoid routing hoses in areas where damage may occur due to build up of material (e.g. dirt, mud, snow, ice, etc.). 2 VSN® Installation Manual for Case AFS Connect Steiger and New Holland PLM T9 (MY 2021 and Newer)

  • Page 7: Harness Routing

    The word “harness” is used to describe any electrical cables and leads, both bundled and unbundled. Use the following guidelines and recommendations when connecting and routing harnesses while installing or maintaining this Raven system: • Leave protective caps/covers over harness connectors until needed to avoid dirt and moisture from contaminating electrical circuits.
  • Page 8 CHAPTER 1 4 VSN® Installation Manual for Case AFS Connect Steiger and New Holland PLM T9 (MY 2021 and Newer)

  • Page 9: Chapter 2 Introduction

    C H A P T E R 2 The following instructions are designed to assist with the proper installation of the VSN® system. Refer to the VSN Calibration & Operation Manual (P/N 016-2020-001) for assistance with calibrating and using the VSN system.

  • Page 10: Recommendations

    We will not share your email or any information you provide with anyone else. Your feedback is valued and extremely important to us. Thank you for your time. 6 VSN® Installation Manual for Case AFS Connect Steiger and New Holland PLM T9 (MY 2021 and Newer)

  • Page 11: Kit Contents

    KIT CONTENTS This section contains a list of the components that are included in the VSN® unit kit. Before beginning the system installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
  • Page 12 CHAPTER 2 8 VSN® Installation Manual for Case AFS Connect Steiger and New Holland PLM T9 (MY 2021 and Newer)

  • Page 13: Chapter 3 Installation

    I NSTALLATION CHAPTER C H A P T E R 3 FABRICATE THE VSN® UNIT BRACKET 1. Assemble the VSN® Unit subassembly as pictured in Figure 1, “VSN® Unit Subassembly,” below. FIGURE 1. VSN® Unit Subassembly M8 Hardware (Bolt, Lock...
  • Page 14 • No more than ±1/16” (1.6mm) of camera movement, in any direction, throughout full engine RPM range • Ensure to account for the 23-pin connector and cable in the bracket design 10 VSN® Installation Manual for Case AFS Connect Steiger and New Holland PLM T9 (MY 2021 and Newer)
  • Page 15 Hardware must meet ≥750 hours salt fog rating, cannot be stainless steel or Zinc coated and should have an aluminum rich coating. NOTE: The left/right offset is not important for bracket design since it will be calibrated out. Ideally, the VSN should be mounted on the right of the tractor hood. Installation: VSN® Specifications...
  • Page 16 2. Secure the VSN® subassembly to the machine brackets with the included M8 hardware. FIGURE 7. Installed VSN® (Picture is for reference only) 12 VSN® Installation Manual for Case AFS Connect Steiger and New Holland PLM T9 (MY 2021 and Newer)

  • Page 17: System Diagram

    INSTALLATION SYSTEM DIAGRAM FIGURE 8. Case AFS Connect Steiger and New Holland PLM T9 (Model Year 2021 and Newer) VSN® System Diagram (P/N 054-2022-025) Installation: System Diagram...

  • Page 18: Route The Cables

    ROUTE THE CABLES 1. Route the VSN® connector on the Steiger/T9 VSN cable (P/N 115-2020-051) cable from the rear of the machine under the cab on the right hand side and follow lines under the hood to the front right side.
  • Page 19 INSTALLATION FIGURE 11. Cutout on Trim NOTE: Any excess cabling can be secured either under the cab or at the rear of the machine. 4. Connect the two 4-pin ISO connectors at the back of the IBBC connector on the rear of the machine. FIGURE 12.
  • Page 20 7. Route the analog video cable up to port 6 on the Viper®4 or connect on the 8-pin video adapter cable (P/N 115-0172-608) on the optional analog video display. FIGURE 14. Viper® 4 Connection 16 VSN® Installation Manual for Case AFS Connect Steiger and New Holland PLM T9 (MY 2021 and Newer)

  • Page 21: Install The (Optional) Analog Video Kit

    If a CR7™ is used in the machine, the analog video kit (P/N 117-2020-007) may be useful for viewing the video feed from VSN®. The CR7™ does not have an analog video input, so this auxiliary display is used. FIGURE 15. Standalone Height Sensor MOUNT THE ANALOG DISPLAY TO CR7™...

  • Page 22: Cabling

    If desired, more cameras may be purchased and plugged into the other camera inputs on this display. SYSTEM DIAGRAM The system diagram for the VSN® analog video system can be found on the next page. 18 VSN® Installation Manual for Case AFS Connect Steiger and New Holland PLM T9 (MY 2021 and Newer)
  • Page 23 INSTALLATION FIGURE 17. (Optional) VSN® Analog Video System Diagram (P/N 054-2020-003 Rev. A) Installation: Install the (Optional) Analog Video Kit...
  • Page 24 CHAPTER 3 20 VSN® Installation Manual for Case AFS Connect Steiger and New Holland PLM T9 (MY 2021 and Newer)
  • Page 25 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility.
  • Page 26 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility.
  • Page 27 WHAT IS NOT COVERED BY THE EXTENDED WARRANTY? Raven Industries will not assume any expense or liability for repairs outside our facility without written consent. Raven Industries is not responsible for damage to any associated equipment or products and will not be liable for loss of profit, labor, or other damages.

Table of Contents