Install the SmarTrax Node ....................... 11 Mount the SmarTrax Node ....................11 Node Mounting Locations ....................14 Install the Phoenix 200 Antenna (If Applicable) ............... 15 Complete the SmarTrax System Installation ................15 Calibrate the SmarTrax System ....................16 Enable Switch ......................... 16 System Diagrams ........................
Page 4
Table of Contents Case IH Patriot 4420 - Steering Ready (2009 & Newer) SmarTrax™ Installation Manual...
Ensure SmarTrax is disabled prior to starting any maintenance work on SmarTrax or the machine. WARNING • When starting the machine for the first time after installing SmarTrax, be sure that all persons stand clear in case a hose has not been properly tightened. •...
CAUTION Hydraulic Safety • Raven Industries recommends that appropriate protective equipment be worn at all times when working on the hydraulic system. • Never attempt to open or work on a hydraulic system with the equipment running. Care should always be taken when opening a system that has been previously pressurized.
Preparing for Installation Before installing the SmarTrax system, park the machine where the ground is level, clean, and dry. Turn off the machine and leave it turned off for the duration of the installation process. Bleed pressure from the hydraulic system by loosening the hydraulic fittings slowly, where applicable.
Recommendations Raven Industries recommends the following best practices when installing or operating the SmarTrax system for the first time, at the start of the season, or when moving the SmarTrax system to another machine: • Install the GPS antenna in the recommended location. Refer to the following table for the machine-specific antenna mounting location.
This section contains a list of the components that are included in the SmarTrax kit. Before beginning the SmarTrax installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
Installation Prepare for Installation SmarTrax Node Mounting Location FIGURE 1. Identify the SmarTrax node mounting location under the instructional seat. Flip up the seat cushion of the instructional seat and remove the storage tub. Bolts to be Removed FIGURE 2.
Connect the Case steering control cables to the Case interface box (P/N 063-0173-038). Connect the round, 37-pin connector of the node harness (P/N 115-4001-127) to the 37-pin port of the Case interface box. Case IH Patriot 4420 - Steering Ready (2009 & Newer) SmarTrax™ Installation Manual...
Ensure the Case interface box will not interfere with the storage tub when it is reinstalled. Install the SmarTrax Node Mount the SmarTrax Node SmarTrax Node Installed FIGURE 6. Mount the SmarTrax node to the node mounting bracket (P/N 107-0172-084) using three 3/8”-16 nylon insert lock nuts (P/N 312-1001-164). Manual No. 016-5032-015 Rev. C...
Page 16
CAN Connector Installed on Machine’s DIAGNOSTIC Connector FIGURE 8. Connect the CAN extension cable (P/N 115-4001-150) to the machine’s existing DIAGNOSTIC connector bolted to the fuse panel as shown in Figure 8. Case IH Patriot 4420 - Steering Ready (2009 & Newer) SmarTrax™ Installation Manual...
Page 17
Cab Component Installation Route the opposite end of the cable out the fuse panel and around the back of the operator’s seat to the instructional seat compartment. Connect the CAN connector to the CAN connection on the node harness. DGPS OUT Connector Routed Under Operator’s Seat FIGURE 9.
Mounting Tabs When choosing the location for the SmarTrax node, consider the following points: • Mount the SmarTrax node inside the machine’s cab on a flat, level surface for proper performance and cable connection. • One of the six numbered direction arrows on the node must be oriented in the direction of forward vehicle travel, one arrow pointing straight up, and two of the arrows parallel to the ground.
Connect the CASE GPS connection and the DGPS IN connection from the node harness (P/N 115-4001- 127) cable together. Complete the SmarTrax System Installation Reinstall the back panel of the instructional seat compartment. Reinstall the fan assembly. Replace the storage tub.
Chapter 3 Calibrate the SmarTrax System Refer to the SmarTrax and SmartSteer Calibration & Operation Manual (P/N 016-0171-277) for instructions on calibrating the SmarTrax system, adjusting system settings, and system operation. Enable Switch Enable Switch. FIGURE 14. A factory-installed switch is installed on the floor of the machine’s cab. Use this enable switch to engage and disengage the SmarTrax system after installation and calibration of the system is complete.
Cab Component Installation System Diagrams Manual No. 016-5032-015 Rev. C...
Page 22
Chapter 3 Case IH Patriot 4420 - Steering Ready (2009 & Newer) SmarTrax™ Installation Manual...
Page 23
Index Cab Component Installation Calibrating the SmarTrax System 16 Enable Switch 16 Install the Phoenix 200 Antenna 15 Installing the Case Interface Box 10 Installing the SmarTrax Node 11 Mounting the SmarTrax Node 11 Node Mounting Locations 12, 14 Preparing for Installation 9...
Page 24
Index Case IH Patriot 4420 - Steering Ready (2009 & Newer) SmarTrax™ Installation Manual...
Page 25
Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
Page 26
How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.