Table of Contents
Advertisement
OPERATION
Preparations:
Before setup, fill in the date of first use on the "(Check records)" label
①
on the inner surface of the front panel.
:ﺍﻻﺳﺗﻌﺩﺍﺩﺍﺕ
.ﻗﺑﻝ ﺍﻹﻋﺩﺍﺩ، ﺍﻣﻸ ﺗﺎﺭﻳﺦ ﺃﻭﻝ ﺍﺳﺗﺧﺩﺍﻡ ﻋﻠﻰ ﻣﻠﺻﻖ ")ﺍﻟﺗﺣﻘﻖ ﻣﻥ ﺍﻟﺳﺟﻼﺕ(" ﻋﻠﻰ ﺍﻟﺳﻁﺢ ﺍﻟﺩﺍﺧﻠﻲ ﻟﻠﻭﺣﺔ ﺍﻷﻣﺎﻣﻳﺔ
Insert the power plug into the power outlet.
②
Supply/drain water. (→"Water supply/drainage method" on Page 13 ~ 15)
③
1
Start to operate.
.ﺑﺩء ﺍﻟﺗﺷﻐﻳﻝ
(The operation
indicator lights on)
)ﻋﻧﺩﻣﺎ ﻳﺿﻲء ﻣﺅﺷﺭ
(ﺍﻟﺗﺻﺭﻳﻑ ﺍﻟﺗﺷﻐﻳﻝ
2
Select the
operation mode.
.ﺣﺩﺩ ﻭﺿﻊ ﺍﻟﺗﺷﻐﻳﻝ
Press this button to
switch level by level.
ﺍﺿﻐﻁ ﻋﻠﻰ ﻫﺫﺍ ﺍﻟﺯﺭ ﻟﺗﺑﺩﻳﻝ ﺑﻳﻥ
.ﺍﻟﻣﺳﺗﻭﻯ ﻭﺍﻵﺧﺭ
(The indicator lights on)
()ﻋﻧﺩﻣﺎ ﻳﺿﻲء ﺍﻟﻣﺅﺷﺭ
.ﺿﻊ ﻣﻧﻔﺫ ﺍﻟﺗﻳﺎﺭ ﻓﻲ ﻣﻧﻔﺫ ﺍﻟﺗﻳﺎﺭ
(15~13 ﺗﻭﺭﻳﺩ / ﺗﺻﺭﻳﻑ ﺍﻟﻣﻳﺎﻩ. )←"ﺍﻹﻣﺩﺍﺩ ﺑﺎﻟﻣﻳﺎﻩ/ﻁﺭﻳﻘﺔ ﺍﻟﺗﺻﺭﻳﻑ" ﻓﻲ ﺻﻔﺣﺔ
The product enters preparatory operation in about
●
20 seconds after the button is pressed. (When the
brightness switch is turned on, the status indicator
starts blinking on both ends at the same time.)
ﻳﺩﺧﻝ ﺍﻟﻣﻧﺗﺞ ﺍﻟﻌﻣﻠﻳﺔ ﺍﻟﺗﺣﺿﻳﺭﻳﺔ ﻓﻲ ﺣﻭﺍﻟﻲ 02 ﺛﺎﻧﻳﺔ ﺑﻌﺩ ﺍﻟﺿﻐﻁ ﻋﻠﻰ ﺍﻟﺯﺭ. )ﻋﻧﺩ ﺗﺷﻐﻳﻝ
(.ﻣﻔﺗﺎﺡ ﺍﻟﺳﻁﻭﻉ، ﻳﺑﺩﺃ ﻣﺅﺷﺭ ﺍﻟﺣﺎﻟﺔ ﻓﻲ ﺍﻟﻭﻣﻳﺽ ﻋﻠﻰ ﻛﻼ ﺍﻟﻁﺭﻓﻳﻥ ﻓﻲ ﻧﻔﺱ ﺍﻟﻭﻗﺕ
The product does not blow out air during preparatory
●
operation.
After the preparatory operation is completed, the
●
product starts to operate.
The air volume can be set in 3 levels.
●
Low
ﻣﻧﺧﻔﺽ
The factory setting is "High" mode.
●
It can be set during preparatory operation.
●
Replacement of anti-fungus assembly
●Approx. once every five years
(When operating 12 hours a day)
Part No.
JDJPL7000023
Date installed:
Replacement of dust filter
●Approx. once every two years
(When operating 12 hours a day)
Part No.
JDJPL7000012
Date installed:
Replacement of sterilization filter
●Approx. once every five years
(When operating 12 hours a day)
Part No.
JDJPL7000020
Date installed:
Replacement of electrode unit
●When the electrode unit replacement indicator
blinks (Approx. once every five years)
Part No.
JDJPL7000016
Date installed:
.ﻻ ﻳﺧﺭﺝ ﺍﻟﻣﻧﺗﺞ ﻫﻭﺍ ء ً ﺃﺛﻧﺎء ﺍﻟﺗﺷﻐﻳﻝ ﺍﻟﺗﺣﺿﻳﺭﻱ
.ﺑﻌﺩ ﺍﻛﺗﻣﺎﻝ ﺍﻟﻌﻣﻠﻳﺔ ﺍﻟﺗﺣﺿﻳﺭﻳﺔ، ﻳﺑﺩﺃ ﺍﻟﻣﻧﺗﺞ ﻓﻲ ﺍﻟﻌﻣﻝ
.ﻳﻣﻛﻥ ﺿﺑﻁ ﺣﺟﻡ ﺍﻟﻬﻭﺍء ﻋﻠﻰ 3 ﻣﺳﺗﻭﻳﺎﺕ
Med
High
ﻣﺗﻭﺳﻁ
ﻋﺎﻟﻲ
."ﺇﻋﺩﺍﺩ ﺍﻟﻣﺻﻧﻊ ﻋﻠﻰ ﺍﻟﻭﺿﻊ "ﻋﺎﻟﻲ
.ﻳﻣﻛﻥ ﺿﺑﻁﻪ ﺃﺛﻧﺎء ﺍﻟﻌﻣﻠﻳﺔ ﺍﻟﺗﺣﺿﻳﺭﻳﺔ
ﺍﻟﺗﺷﻐﻳﻝ
11
Advertisement
Table of Contents
