Product Warnings - Copley Controls Accelnet Plus AEV-090-14 User Manual

Accelnet Plus Micro Modules User Guide
P
RODUCT
DANGER: HAZARDOUS VOLTAGES.
!
Exercise caution when installing and adjusting. Persons responsible for installing and commissioning
Accelnet Plus Micro Module servo drives must be experienced in all aspects of electrical equipment
installations.
DANGER
FAILURE TO HEED THIS WARNING CAN CAUSE EQUIPMENT DAMAGE, INJURY, OR DEATH.
RISK OF ELECTRIC SHOCK.
!
DC Supplies used to power Accelnet Plus Micro Module drives must be transformer-isolated and
provide reinforced insulation from AC mains power.
DANGER
FAILURE TO HEED THIS WARNING CAN CAUSE EQUIPMENT DAMAGE, INJURY, OR DEATH.
RISK OF UNEXPECTED MOTION WITH NON-LATCHED FAULTS.
After the cause of a non-latched fault is corrected, the drive re-enables the PWM output stage
without operator intervention. In this case, motion may re-start unexpectedly. Configure faults as
!
latched unless a specific situation calls for non-latched behavior. When using non-latched faults, be
sure to safeguard against unexpected motion.
DANGER
FAILURE TO HEED THIS WARNING CAN CAUSE EQUIPMENT DAMAGE, INJURY, OR DEATH.
USING CME OR SERIAL COMMANDS MAY AFFECT OR SUSPEND CAN OR ETHERCAT
OPERATIONS.
When operating the drive as a CAN or EtherCAT node over a network, the use of CME or ASCII
!
serial commands may affect network operations in progress. Using such commands to initiate
motion may cause network operations to suspend. Network operations may restart unexpectedly
DANGER
when the commanded motion is stopped.
FAILURE TO HEED THIS WARNING CAN CAUSE EQUIPMENT DAMAGE, INJURY, OR DEATH.
LATCHING AN OUTPUT DOES NOT ELIMINATE THE RISK OF UNEXPECTED MOTION
WITH NON-LATCHED FAULTS.
!
Associating a fault with a latched, custom-configured output does not latch the fault itself. After the
cause of a non-latched fault is corrected, the drive re-enables without operator intervention. In this
DANGER
case, motion may re-start unexpectedly.
FAILURE TO HEED THIS WARNING CAN CAUSE EQUIPMENT DAMAGE, INJURY, OR DEATH.
USE EQUIPMENT AS DESCRIBED.
!
Operate drives within the specifications provided in this manual.
FAILURE TO HEED THIS WARNING CAN CAUSE EQUIPMENT DAMAGE, INJURY, OR DEATH.
DANGER
REFER TO SECTIONS 5, 6, & 7 OF THIS DOCUMENT
!
The information provided in these sections of this document must be considered
for any application using the STO feature.
DANGER
FAILURE TO HEED THIS WARNING CAN CAUSE EQUIPMENT DAMAGE, INJURY, OR DEATH.
DO NOT PLUG OR UNPLUG CONNECTORS WITH POWER APPLIED.
!
The connecting or disconnecting of cables while the drive has VLOGIC and/or +HV power applied is
not recommended.
WARNING
FAILURE TO HEED THIS WARNING MAY CAUSE EQUIPMENT DAMAGE.
REFER TO THE INFORMATION IN SECTION 6 OF THIS USER MANUAL REGARDING STO
!
AND FUNCTIONAL SAFETY.
The information provided within must be considered for any application using the STO feature
DANGER
FAILURE TO HEED THIS WARNING MAY CAUSE EQUIPMENT DAMAGE, INJURY OR DEATH
Models AEV-EZ-090, AEV-EZ-180, APV-EZ-090 and the APV-EZ-180 EZ boards are not compatible
with and must not be used with the AEV-090-50, AEV-090-50-C, APV-090-50 or APV-090-50-C
!
Accelnet Micro Modules.
Refer to models AEZ-090-50, AEZ-090-50-C, APZ-090-50 and APZ-090-50-C instead.
WARNING
Failure to heed this warning may cause equipment damage or injury.
Observe all relevant state, regional and local safety regulations when installing and using this product. Be
sure that all wiring complies with the National Electrical Code (NEC) or its national equivalent, and all
prevailing local codes. There are no user serviceable parts in the Accelnet Plus Micro Module servo drives.
Copley Controls
W
ARNINGS
16-01687 Rev 03
Page 8 of 139