Siemens LMV50 Series Manual page 321

Building Technologies
Digital inputs
X3-02 pin 1
X3-04 pin 1 / X3-03 pin 1
X4-01 pin 1 / pin 2
X4-01 pin 3
X4-01 pin 4
X4-03
X5-01 pin 2
X5-02 pin 2
X5-03 pin 1
X5-03 pin 2 / pin 3
X6-01 pin 1
X6-01 pin 3
X7-03 pin 2
X9-03 pin 2
X9-03 pin 3
X9-03 pin 4
digital outputs
Digital outputs
X3-01 pin 1
X3-01 pin 2
X4-02
X6-02
X8-01
X8-02, X8-03, X7-01, X7-02, X6-03 57
X9-01
dimensions
direct entry of O2 min values
direct ignition with heavy oil, modulating28
direct ignition with heavy oil, multistage
direct ignition with light oil, modulating
direct ignition with light oil, multistage26
direction of rotation
display and operating unit AZL5
display and settings
disposal notes
dual-fuel burner gas/heavy oil with gas
pilot ignition
dual-fuel burner gas/light oil with gas
pilot ignition
duties of the authorized inspector
E
eBus PC adapter
electrical connection of ionization probe
and flame detector
electrical connections and wiring
Electronic fuel-air ratio control
Activating / deactivating actuators 85
Actuator addresses
Approaching low-fire phase 50/54 89
Direction of rotation of actuator
Startpoint operation
Electronic ratio control
Traveling times
Electronic ratio control
Actuator speed in normal operation
Actuator speed outside normal
operation
Idle position
Ignition positions
Basic DocumentatiohnLMV5...
23 Index
43
Limitation of load range
48
Masking out load range
42
Multistage operation
44
Position check, safety time
44
Postpurge positions
43
Prepurge position
58
Program stop
53
Special features
54 Electronic ratio control
46 Shutdown behavior
Electronic ratio control
47
Overload protection
54
EMC
55
end of operating position
51
entry of password
environmental conditions
48
external setpoint changeover
53
external setpoints or predefined load via
50
digital
56
Extra functions
Extraneous light
56
Extra functions
56
Continuous fan
56
Forced intermittent operation
58
Gas shortage program
57
Low-fire shutdown
Normal / direct start
57
Phase 00 / phase 01
234, 302
Prepurging
282
Program stop function
Repetition counter
28
Safety shutdown
Start preventions
27
F
149
first submenu level
130
Flame signal display AZL5
139
extraneous light
19
flame signal input and flame detector
X10-01 and X10-03
31
fourth submenu level
fuel changeover
30
fuel meter
225
fuel meter input X71/X72
fuel meter readings
224 fuel train applications
fuel-air ratio control system
15 Fuel-air ration control
213 function principle of FGR
functioning principle of O2 trim control
84
G
gas direct ignition
gas pilot ignition 1
86
gas pilot ignition 2
88
gas valve proving
general
98
H
heating up the QGO20 after power-on
91
heavy oil direct ignition
heavy oil with gas pilot ignition
90
I
87
initializing the O2 trim controller
87
input 1, TEMP, Pt100 sensor X60
97
98
92
93
90
87
96
96
98
99
248
89
146
233
122
122
69
69
65
67
68
68
63
66
67
64
65
65
147
39
32
148
71
242
242
246
25
226
84
289
252
25, 73
25, 74
25, 75
61
20
257
77
79
259
118
321/327
CC1P7550en
22.05.2018